Table of Contents
Advertisement
Available languages
Available languages
− Damaged or illegible safety warning labels should be
replaced immediately.
Repairs to other parts of the machine must be carried out
by the manufacturer or one of his customer service
points.
Use only original spare parts, accessories and special
accessory parts. Accidents can arise for the user through
the use of other spare parts. The manufacturer is not li-
able for any damage or injury resulting from such action.
D
e
s
c
r
i
p
t
i
o
n
D
e
s
c
r
i
p
t
i
o
n
Pos.
Denomination
1
Cutting head
2
Protective hood
3
Plant protection bow
4
Clamping knob
5
Screw
6
Front handle
7
Clamping screw
8
Wheel set
9
Charging unit
10
Transformer unit
11
Battery
12
Trip switch
13
ON-OFF switch
14
Clamping nut
15
Cutting thread
16
Thread knife
17
Spool cover
18
Thread spool cpl.
19
Spring
20
Lawn trimmer – lower part
21
Lawn trimmer – upper part
22
Safety label
A
s
A
s
Always start the machine when it is completely assem-
bled.
Attaching the protective hood
Remove both screws (A) and washers from the cutting
head (1).
Slide the protective hood (2) over the cutting head (1)
Fasten the protective hood (2) to the cutting head (1)
using the screws and washers (A).
Attaching the plant protection bow
Plug both ends of the plant protection bow (3) in the
openings of the cutting head provided for them.
17
o
f
d
e
v
i
c
e
/
s
p
a
r
e
p
o
f
d
e
v
i
c
e
/
s
p
a
r
e
p
Order-No.
380830
380893
380844
380837
380832
364151
364150
380841
380842
380835
380829
380896
380895
380890
380828
s
e
m
b
l
i
n
g
s
e
m
b
l
i
n
g
Attaching the front handle
Remove the clamping knob (4) and pull out the screw (5)
out of the handle.
Put the handle (6) on the holder on the product.
Put the screw (5) through the handle (6) and holder and
secure it using the clamping knob (4).
Before tightening the clamping knob (4) you can adjust
the front handle (6) as desired. Then, tighten the clamp-
ing knob (4).
Attaching the wheel set
a
r
t
s
a
r
t
s
Unscrew the clamping screw (7) out of the wheel set (8).
Slide the wheel set (8) on the holder on the cutting
head (1).
Firmly tighten the clamping screw (7).
---
C
h
a
r
g
i
n
g
C
h
a
r
g
i
n
g
---
Always use the supplied charger to charge the
lithium ion battery supplied with the machine.
Mains connection
Compare the voltage given on the machine model plate e.g.
230 V with the mains voltage and connect the device to the
relevant and properly earthed plug.
Fully charge the lithium ion batteries before first use or
after a longer storage period of the machine.
The rechargeable battery will reach its full capacity only
---
after several charge-discharge cycles.
Connect the transformer unit (9) to the charging unit (10).
Plug the transformer unit (9) in the mains socket. The
LED (A) lights
---
Slide the battery (11) in the charging unit.
---
The charging indicator LED (A) will light up red.
Charging is in progress.
During the charging process, the charger is heated
and a low humming noise can be heard. This is normal.
The charging process is completed after approx. 3 hours.
The LED (A) lights green.
After completed charging, remove the battery (11) and dis-
connect the charger from the mains.
S
w
i
t
c
h
i
n
g
S
w
i
t
c
h
i
n
g
S
w
i
t
c
S
w
i
t
c
The lawn trimmer has a protective shut-down which pre-
vents an unintended switching on.
Insert the battery (11) in the machine.
Make sure to slide the battery fully in until it engages
with a click.
B
e
f
o
r
e
t
h
e
f
i
r
s
t
s
B
e
f
o
r
e
t
h
e
f
i
r
s
t
s
t
h
e
r
e
c
h
a
r
g
e
a
b
l
e
b
a
t
t
e
r
t
h
e
r
e
c
h
a
r
g
e
a
b
l
e
b
a
t
t
e
r
ready for operation.
S
t
a
r
t
-
u
p
S
t
a
r
t
-
u
p
o
n
/
o
f
f
o
n
/
o
f
f
h
o
n
h
o
n
t
a
r
t
-
u
p
t
a
r
t
-
u
p
y
y
Advertisement
Chapters
Table of Contents
