Philips 221TE2LB/00 Service Manual

21.5 inch fhd tft lcd colour monitor(tv)

Hide thumbs Also See for 221TE2LB/00:

User manual (33 pages)

Quick manual (3 pages)

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

Table of Contents

Quick Links

Troubleshooting

Summary of Contents for Philips 221TE2LB/00

Page 1: Table Of Contents
AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING ELECTRONIC EQUIPMENT CONTAINING HIGH VOL TAGES. CAUTION: USE A SEPARATE ISOLATION TRANSFORMER FOR THIS UNIT WHEN SERVICING. REFER TO BACK COVER FOR IMPOR T ANT SAFETY GUIDELINES Published by Philips Consumer Lifestyle Copyright reserved Subject to modification JDec 09 2010...
Page 2: Important Safety Notice
SERVICE MANUAL. recommended by Philips must f irst sati sfy himself thoroughly that neither his safety nor the saf e operation of the equipment will be jeopardized by the service method sel ected.
Page 3: Technical Data
221TE2L LCD Technical Data D-SUB PIN No. SIGNAL PIN No. SIGNAL DDC +3.3V or +5V Type NR. : AUO M215HW01 V7 Green/ SOG Logic GND Resolution : 1920x1080 Blue Sense (GND) Outside dimensions : 495.6(H) x 292.2(V) x 11(D) Typ Sense (GND) Bi-directional data Pitch (mm)
Page 4: Technical Data
221TE2L LCD Technical Data D-SUB PIN No. SIGNAL PIN No. SIGNAL DDC +3.3V or +5V Type NR. : CPT CLAA215FA 03S Green/ SOG Logic GND Resolution : 1920x1080 Blue Sense (GND) Outside dimensions : 495.6(H) x 292.2(V) x 11.4(D) Typ Sense (GND) Bi-directional data Pitch (mm)
Page 5: Installation
221TE2L LCD Installation Front View Product Description Rear View...
Page 6 221TE2L LCD Installation...
Page 7 221TE2L LCD Installation...
Page 8 221TE2L LCD Installation...
Page 9 221TE2L LCD Installation...
Page 10 221TE2L LCD Installation...
Page 11: Troubleshooting
221TE2L LCD Troubleshooting...
Page 12: Troubleshooting
221TE2L LCD Troubleshooting...
Page 13: On Screen Display
What is the On-Screen Display? On-Screen Display (OSD) is a feature in all Philips LCD monitors. It allows an end user to adjust screen performance or select functions of the monitors directly through an on-screen instruction window. A user friendly on screen display...
Page 14: On Screen Display
221TE2L LCD On-Screen Display Supported display resolutions...
Page 15: Lock/Unlock, Aging,Factory Mode
221TE2L LCD To lock/unlock OSD FUNCTION(User Mode) Step 2 : By pressing " UP" and " DOWN " key to Burning Icon. Press "MENU then press " UP" and "DOWN " key to turn on Aging Mode. The OSD function can be locked by pressing"OK"button(1) for more than 10 seconds, the screen shows following windows for 4 seconds.
Page 16: Philips Pixel Defect Policy
Pixel Defect Tolerances In order to qualify for repair or replacement due to pixel defects during the warranty period, a TFT LCD panel in a Philips flat panel monitor must have Pixels and Sub pixels pixel or sub pixel defects exceeding the tolerances listed in the following A pixel, or picture element, is composed of three sub pixels in the primary tables.
Page 17: Mechanical Instructions
221TE2L LCD Mechanical Instruction Preparation before disassemble 1.Clean the room for disassemble 2.Identify the area for monitor 3.Check the position that the monitors be placed and the quantity of the monitor ;prepare the area for material flow; according to the actual condition plan the disassemble layout 4.Prepare the implement, equipments, materials as bellow: 1) Press-fixture 2) working table...
Page 18: Mechanical Instruction
221TE2L LCD Mechanical Instruction Disassemble the CVR Tear off the LVDS cable Please carefully use from the Panel two hands (one hand And the PCBA connect presses the locking-latch of LVDS cable’s housing, and at the same time another hand pulls out the LVDS cable.) for this step to avoid from deforming the...
Page 19 221TE2L LCD Mechanical Instruction Disassemble the two adhesive tape and tear off the bugle cable Disassemble screws then Take the Main-BKT out of the Panel Tear down control cable and bugle cable from the Panel , then take the Panel out from the Disassemble the bugle Screw-driver 4 screws...
Page 20 221TE2L LCD Mechanical Instruction Tear off the Mylar from the C/B , then Disassemble Lens Disassemble the PCBA Screw-driver board 12 screw Take the PCBA from Main-BKT and then put it on the cushion Disassemble the driver Screw-driver board 1 screw Disassemble the Screw-driver column...
Page 21: Mechanical Instructions
221TE2L LCD Mechanical Instruction Disassemble the Screw-driver hinge 1 screw...
Page 22: Color Adjustment
There are six factory preset white color 11500K, 9300K, 8200K, 7500K, 6500K, sRGB, 5000K Align by Philips PerfecTune (also called FGA) function. Apply full white pattern, with brightness in 100 % position and the contrast control at 50 % position.
Page 23: Faqs (Frequently Asked Questions)
221TE2L LCD FAQs (Frequently Asked Questions)
Page 24 221TE2L LCD FAQs (Frequently Asked Questions)
Page 25: Electrical Instruction
221TE2L LCD Electrical Instructions Electrical characteristics 1. VIDEO SIGNAL REQUIREMENTS 1.1 CVBS input -1000mVpp (including 300 mV sync level), terminated with input impedance of 75 . 1.2 S-Video input - Y: 1000mVpp, C: 300mVpp, terminated with input impedance of 75 . 1.3 Component video input - Y: 1000mVpp, PbPr: ±350mVpp, terminated with input impedance of 75 .
Page 26: Electrical Instruction
221TE2L LCD Electrical Instructions White color adjustment There are three factory preset white color 9300K, 6500K, sRGB. Apply full gray64 pattern, with brightness in 100 % position and the contrast control at 50 % position.The 1931 CIE Chromaticity (color triangle) diagram (x ,y) coordinate for the screencenter should be: YPBPR:Timing 720P pattern color bar 100 VGA: Timing 800*600 60Hz pattern gray scale H-32step DTV(MMD)
Page 27: Service Tool
221TE2L LCD Service tool-Hardware PCM code 12NC 5E.L8215.001 996510019769...
Page 28: Service Tool
221TE2L LCD Service tool-Software Firmware writing tool : MStar ISP Utility V4.4.9.5 DDC writing tool: Q-EDID-V30...
Page 29: Ddc Instructions & Serial Number
221TE2L LCD DDC Instructions DDC Data Re-programming In case the DDC data memory IC or main EEPROM which storage all factory settings were replaced due to a defect, the serial numbers have to be re-programmed "Analog DDC IC, Digital DDC IC & EEPROM". It is advised to re-soldered DDC IC and main EEPROM from the old board onto the new board if circuit board have been replaced, in this case the DDC data does not need to be re-programmed.
Page 30 221TE2L LCD DDC Instructions 5. Connect and Mains cord to Monitor as shown in Fig.2. Fig.2 Pin assignments : A. 15-pin D-Sub Connector PIN No. SIGNAL PIN No. SIGNAL DDC +3.3V or +5V Green/ SOG Logic GND Blue Sense (GND) Sense (GND) Bi-directional data Cable Detect (GND)
Page 31 221TE2L LCD DDC Instructions 6. Setup the Philips-IMS EDID Tools program Step 1: Open Q-EDID V030 Software into your folder as shown in Fig.3. and Fig.4. Fig.3 Fig.4...
Page 32 221TE2L LCD DDC Instructions Step 2: Press “Open File” then choose 191TE2L_EDID_VGA.ddc or 191TE2L_EDID_HDMI.ddc as shown in Fig. 5 . Fig.5...
Page 33 221TE2L LCD DDC Instructions Step 3 : Load DDC file success as shown in Fig. 6 . Fig.6 Step 4 : update Serial number and press enter to correct S/N number shown as Fig.7 . Fig.7...
Page 34 221TE2L LCD DDC Instructions Step 5 : Press “RUN” to write EDID and serial number shown as Fig.8 . Fig.8 Step 6 : EDID and serial number update success shown as Fig.9 Fig.9...
Page 35 221TE2L LCD DDC Instructions 8. Press “Read EDID” to read EDID and serial number shown as Fig.10 . and check Serial number is the same as we set. Note: If not the same, please rewrite EDID S/N again. Fig.10 Serial Number Definition...
Page 36: Ddc Data
Detailed Timing: 1920x1080 @60Hz Composite Sync. support: Detailed Timing: FF (Monitor SN) 'NT00000000001' Vsync. Pulse: serration required Detailed Timing: FC (Monitor name) 'Philips 221TE' Max Horz Image Size: 48 cm. Detailed Timing: FD (Monitor limits) Max Vert Image Size: 27 cm.
Page 37: Ddc Data
1430 1650 720 725 730 750 +hsync +vsync 2,D0,1E,20,B8,28,55,40,9A,E6,10,00,00,1E,65 Detailed timing #4..1920x1080i at 50Hz (16:9) Modeline...."1920x1080" 74.250 1920 2448 Model name....Philips 221TE 2492 2640 1080 1084 1094 1124 interlace -hsync +vsync Manufacturer..... Philips Detailed timing #5..1280x720p at 50Hz (16:9) Plug and Play ID..
Page 38: Firmware Upgrade For Cpu
221TE2L LCD Firmware Upgrade for CPU I. I2C upgrade FW 1. Hardware Requirement: 1.1. I2C board x 1 (a.Print Board b. I2C Board) 1.2. DSUB VGA cables x 2 1.3. Printer cable (with one male connector and another female connector) x 1. 1.4.
Page 39 221TE2L LCD Firmware Upgrade for CPU Link “I2C BD, Power cable and Signal cable 2. Software prepare MStar ISP Utility V4.4.9.5 MSTAR ISP Tool 4.4.9.5 DebugTool_V6.7_200 Step 1: Press MStar ISP Tool Step 2: Choose Option “Config”, set Port type to “LPT1”; set I2C Speed Setting to , Press “Auto Detect”...
Page 40 221TE2L LCD Firmware Upgrade for CPU Step 4: Choose Option “Connect”, the tool will show FLASH type as below, then press “OK”...
Page 41: Firmware Upgrade For Cpu
221TE2L LCD Firmware Upgrade for CPU Step 5: Choose Option “Auto”, then press “Run” Step 6: Choose Option “Auto”, and then press “Run”; the firmware will upgrade complete after the message shows “PASS”...
Page 42: Failure Mode Of Panel
221TE2L LCD Failure Mode Of Panel Quick reference for failure mode of LCD panel this page presents problems that could be made by LCD panel. It is not necessary to repair circuit board. Simply follow the mechanical Polarizer has bubbles instruction on this manual to eliminate failure by replace LCD panel.
Page 45: Scaler Diagram & C.b
N C _ 0 . 1 U 5 0 V N C _ 0 . 1 U 5 0 V N C _ 0 . 1 U 5 0 V N C _ 0 . 1 U 5 0 V...
Page 48 0. 047U K...
Page 53 221TE2L LCD S c alar Diagram & C .B .A...
Page 55 84. 008M 3. 0 30 84. 008M 3. 0 30...
Page 56: Power Diagram & C.b
221TE2L LCD Power Diagram & C.B .A...
Page 57 221TE2L LCD Power Diagram & C.B .A...
Page 58 OZ9998A...
Page 59: Led Driver Diagram & C.b
221TE2L LCD LED Diagram & C.B .A...
Page 61: Control Diagram & C.b
221TE2L LCD C ontrol Diagram & C .B .A.
Page 63: Ir Diagram & C.b
221TE2L LCD IR Diagram & C.B .A...
Page 64: General Product Specification
221TE2L LCD General Product Specification M2- 221TE2L GENERAL PRODUCT SPECIFICATION Issued by: Argent Chan/Paul Tsai Revision History Ver. Date Author Brief Description (yy.mm.dd) 2008.08.01 Initiate version, TV-M models 2010/11/01 Paul To update 221TE2L data Blue: Changes than last version Red: TBD ©...
Page 65 221TE2L LCD General Product Specification TABLE OF CONTENTS Document change history 1 Introduction Purpose scope Definitions, acronyms & abbreviations References 2 General description Product perspective Product Range Dispplay Panel 3 FUNCtion requirements POWER 3.1.1 POWER SUPPLY FEATURES 3.1.2 POWER CONSUMPTION & MEASURE THE FOLLOWING VOLTAGE 3.1.3 POWER MODE 3.1.4...
Page 66 6 ACCESSORIES Cables Remote Control Quick User Guide Warranty card 7 MECHANICAL Cosmetic Mechanical Data Files Location of Philips Logo Location of Icons Color for Resin / Paint Resins Paint Used Plastic Mold Tooling Plastics Flammability 7.10 Texture/Glossing of Housing 7.11...
Page 67 221TE2L LCD General Product Specification 8 RELIABILITY / ENVIRONMENT MTBF prediction Demonstration MTBF Temperature Humidity Altitude Air pressure Environmental test 9 REGULATORY COMPLIANCE Worldwide Regulatory EMC Requirements RoHS WEEE Ongoing Regulatory Distribution list © MMD 2010 Page 4 of 45...
Page 68: General Description
PAL/SECAM of the air or from the cable and AV connectors for multiple video format inputs 1.2.1 EDID info, Data for EDID & .inf file User visible strings on .inf file Philips 221TE (22inch WIDE LCD MONITOR 221TE2) Manufacturer ID ( EDID data) Product ID, "xxxx" 4 codes MSB(byte 12): C0...
Page 69 User-friendly remote controller Software upgrade should be done through OAD, USB port. Product Range Destination Mains Cord Eastern/Western Follow Europe , UK Philips’s SKU DISPLAY PANEL Standard 221TE2L CCFL, 250nits AUO M215HW01 V7 CCFL, 250nits CPT CLAA215FA03S © MMD 2010...
Page 70 Barometric pressure - 860 mbar ~ 1013 mbar. Dark room conditions - < 1 lux for optical measurements The RF tuning system and video performance should fulfil Philips torture room test and field test requirements. © MMD 2010 Page 7 of 45...
Page 71 221TE2L LCD General Product Specification POWER 3.1.1 POWER SUPPLY FEATURES AC line voltage range - 90Vac ~ 264Vac. AC line frequency range - 50/60 Hz 3 Hz. DC tact switch - Minimal power consumption when switch off. Inrush current - <...
Page 72 221TE2L LCD General Product Specification 3.1.4 MONITOR DPM / TV STANDBY DPM - The monitor enters DPM off (sleep) mode when no H&V sync or one of H-sync / V-sync input is absent. “No Video Input” message appears before entering DPM mode. A delay of 30 seconds before entering the power saving state is required to avoid misunderstanding of display resolution and timing mode changes.
Page 73 221TE2L LCD General Product Specification And on the grid: (for Australia) In the DVB-T profile, the iDTV supports, besides the European Grid, Australian grid. There, the center frequency F is located +/- 500Khz on a grid: For VHF : F = N*7 + 2.5 ; for 25<=N<=32 For UHF : F = N*7 + 4.5;...
Page 74 ETSI TS 101 154, D-Book for UK and DVB SSU simple profile. Any software upgrade (over the air ) requires authentication: to make sure that it will only load an image approved by Philips. (for example using SHA-2) (DTV only) DVB Subtitles - Supports to display subtitles which broadcasted via DVB or reinserted TXT.
Page 75 221TE2L LCD General Product Specification 3.2.2.1 RC function keys 3.2.2.2 Status indicator The Status Indicator is a sign to show the status of Text mode. There are 4 status are identified: Normal page display, Page Number Entry by Digit, Subcode Entry by Digit, and Page Hold. 3.2.2.3 Status line The Status Line is defined as:...
Page 76 221TE2L LCD General Product Specification 3.2.2.4 Table of page (TOP) A type of teletext transmission in which special pages are transmitted that give information about other pages in the transmission. 3.2.2.5 Link control byte (LCB) It is contained in a packet 27 to validate the links for the color keys. 3.2.2.6 Video programming system (VPS) A mechanism by which the broadcast ID is transmitted using Teletext transmission.
Page 77 221TE2L LCD General Product Specification SCART - Full SCART, includes CVBS in/out, RGB/Sync, audio L/R in/out. Pin 8, the function-switching pin, carries a signal from the source that indicates the type of video present, 0V means no signal, or internal bypass +6V means a widescreen (16:9) signal +12V means a normal (4:3) signal Define SCART behavior:...
Page 78 221TE2L LCD General Product Specification System Information allows devices to automatically use the same OSD and Menu language settings as the TV and also for a TV to discover the current language when it is being installed. Give Device Power Status The message is used to determine the current power status of a target device.
Page 79 221TE2L LCD General Product Specification EDID- 221: 3.3.3.1 DDC channel E-EDID data structure according to VESA Enhanced EDID 1.3 (and EIA/CEA-861B for HDMI). Allows source to interrogate capabilities of the Monitor & TV. Separate EDID for VGA input and HDMI input. 3.3.4 I/O CONNECTORS I/O at rear: I/O at Side:...
Page 80 221TE2L LCD General Product Specification 3.3.4.1 Rear connectors: Component Video(YPbPr) & Audio L/R In AV / SC Video & Audio L/R In SCART input / output (CVBS in/out, RGB in,S-Video in, Audio L/R in/out) SPDIF (digital audio) output Coaxial aerial I/P (TV input)– Europe type ( 75 PC VGA In (D-SUB) &...
Page 81 221TE2L LCD General Product Specification HDMI Pin assignment PIN No. SIGNAL TMDS Data2+ TMDS Data2 shield TDMS Data2- TMDS Data1+ TMDS Data1 shield TMDS Data1- TMDS Data0+ TMDS Data0 shield TMDS Data0- TMDS Clock+ TMDS Clock Shield TMDS Clock- Reserved (N.C. on device) DDC/CEC Ground +5V Power Hot Plug Detect...
Page 82 221TE2L LCD General Product Specification VISUAL PERFORMANC PQ setting: 3.4.1 FRONT OF SCREEN PERFORMANCE Peak brightness - Per panel spec, brightness & contrast controls are at 100%. Luminance uniformity - Per panel spec. Chromatic uniformity - Per panel spec. Luminance variation - Per panel spec.
Page 83 221TE2L LCD General Product Specification Over scan - 3 % vertically and horizontally for TV & AV. 0% (fit to screen) for PC mode vertically and horizontally. Residual image - Recover < 2 min. after burn in the checkerboard image for 2 hours.
Page 84 221TE2L LCD General Product Specification Super Zoom Normal(4:3) Zoom1(Movie Expand 14:9) Zoom2(Movie Expand 16:9) Subtitle Zoom Wide AUDIO PERFORMANCE Audio setting: Audio should be audible even no video signal is presented for all sources except PC. For the sake of stereo, proper segment of R/L speakers is needed to make sure correct R/L channel separation.
Page 85 221TE2L LCD General Product Specification 3.5.1 DTV AUDIO CODEC 3.5.1.1 Required Decoders (Reference ETSI TS 101 154 V1.7.1 (2005-06). Section 6.1) Supports ISO/IEC 11172-3 Layer I and Layer II Single channel: Joint stereo Stereo Supports ISO/IEC 13818-3 Multi-channel audio : decode the part ISO/IEC 11172-3 Layer I and Layer II Stereo...
Page 86 221TE2L LCD General Product Specification 3.5.3 INCREDIBLE SURROUND EFFECTS TV front end incredible surround effects are defined as: Transmission received/selected Effect off Effect on 2CS Dual I Mono Spatial 2CS Dual II Mono Spatial NICAM Mono Mono Spatial NICAM Stereo Stereo Incredible Surround NICAM Dual I...
Page 87 221TE2L LCD General Product Specification Side CONtrols Power Source Menu CH- CH+ Vol- Vol+ TV/video mode Source Select Input Source Menu Enter /Exit OSD menu “+” (Volume) Menu Navigate Right/Increase/Volume up “-” (Volume) Menu Navigate Left/Decrease/Volume down “+“ (Channel) Menu Navigate Up/Channel up “-“...
Page 88 221TE2L LCD General Product Specification OSD MENU 25 languages - Bulgarian, Croatian, Czech, Danish, Dutch, English, Finnish, French, Gaelic ,German, Greek, Hungarian, Italian, Norwegian, Polish, Portuguese, Rumanian, Russian, Serbian, Slovak, Slovenian, Spanish, Swedish, Turkish, Ukrianian. OSD tree – As defined. EPG user interface As defined.
Page 89 221TE2L LCD General Product Specification 4.4.2 AUTOSTORE All of the multiplexes are scanned. The services are administered according to their tuple [Original Network ID, Transport Stream ID, Service ID]. Between services with the same tuple, the one from the best reception is chosen. Only services of the proper service type shall be placed in the program list.
Page 90 221TE2L LCD General Product Specification 4.4.5 FINDING A MULTIPLEX The iDTV shall initiate a multiplex search, and the user shall be able to enter any frequency manually and choose between 7Mhz and 8Mhz bandwidth. The iDTV shall then be able to find all DVB-T modulated multiplexes with center frequencies +/-Bandwidth around the manually entered frequency.
Page 91 221TE2L LCD General Product Specification 4.4.7 STORING SERVICES IN THE PSL The mapping between the MSL and PSL is the same for an initial installation as for an update install. Two Services are identical if they have the same [ONID,SID,TSID] If there was no SID or an ONID, then two services are the same if the [network_id,TSID,Program_ID].
Page 92 221TE2L LCD General Product Specification A Service that passes all the selection criteria shall be stored in the Primary Service List The primary service list shall be stored in non-volatile memory and shall include all located analogue TV channels 4.4.8 User Selectable Service Lists All services in the PSL shall be given, per default, the Logical Channel Number (LCN) value of 1000 (maximum LCN +1).
Page 93 221TE2L LCD General Product Specification 4.4.8.2 UNDELETE A service that was deleted by the end user can be undeleted. The service shall be restored at the original preset number that was assigned at the time the service was deleted. When this original preset number is not free (assigned to another service) then a new preset number is assigned to the undeleted service as specified in the SSA 4.4.8.3...
Page 94 221TE2L LCD General Product Specification Each service in a user selectable service list shall be assigned to a unique preset number in the range of 1…MAX_LCN by applying the following rules: 1 In a not unified country, only the LCN’s of the services belonging to the select country will be considered for a direct one-to-one mapping to preset numbers.
Page 95 221TE2L LCD General Product Specification To make it easier for the user to memorize where analogue TV channels are stored in the preset list, the analogue TV channels must be stored at a preset number as specified below: Preferably the analogue TV channels should be stored contiguously at preset numbers below 100, starting at a multiple of 10 plus 1 (for instance 51).
Page 96 Search all available channels automatically. ACI information (if available) can be used to store the channels in the right order. When ACI is not available, PATS (Philips Auto Tuning System) is used to store the found transmitters sequentially from Program 1 to Program 99.
Page 97 221TE2L LCD General Product Specification 5 Non functional requirements DEFAULT AND INITIAL CONTROL VALUES Initial value: Settings when the set turns on from standby. Default value: Out of box settings. Factory reset to default: Settings when “Factory Reset” in menu is selected. Control Initial Value Default Value...
Page 98 221TE2L LCD General Product Specification TIME-OUT Summary of Time-out values: Description Value Menu 20s. Install menu and its subsequent submenus No Timeout Menu to restore last viewed item highlighted 20s. All OSD AV source display (without AV source input) 1.5s for ATV, 2s for DTV Digit entry for change channel Digit entry (General) No sync display in PC mode...
Page 99 221TE2L LCD General Product Specification 5.3.4 CUSTOMER SERVICE MENU (CSM) Based on generic service requirements for OEM (D04.1) + study of data-sheets Hot Key is defined : MENU+062596 Customer service menu 1 1: Set Type ( e.g. 221T1SB/93 ) to be retrieved out of production-data 2: Production code 14 digit production-code to be retrieved per set to be written in NVM./EEPROM...
Page 101 Gap between panel and front bezel < 1.2(typ.) mm Slant on front bezel 4.0MM Fire enclosure request -Shielding Cover should fulfill international standard Resins RoHS requirements. WEEE requirements. Resin type/selection refer to “Plastic-Philips Pool monitor”. © MMD 2010 Page 38 of 45...
Page 102 All major plastic parts (bezel, back cover, base) is better to be molded from same resin. 7.13 Texture/Glossing of Housing The texture area and texture no should follow Philips make-up sheet. The exterior surfaces shall have a uniform texture. Philips must approve the mold texturing.
Page 103 MMD request metal plate in Kinsington hole. 7.17 Wall Mount Method VESA standard 100mm x 100mm 7.18 Label Regulatory label / Carton label should follow Philips requirement. China RoHS label. Detail document refer to Philips Engineering Reference Book. 7.19 Product Dimension / Weight...
Page 104 3. Cold Drop test (for design reference) Un-package test 1. Half sine shock test (non operation) 7.21 Pallet / Container Loading Refer to Philips approved SHT191/SHT560 . Transportation standards refer to TYE-M0002 ,UAN-D1534 and UAW-0309. Request by transportation items: Air shipment...
Page 105 221TE2L LCD General Product Specification RELIABILITY / ENVIRONMENT MTBF prediction >100k hours (excluding Panel) Demonstration MTBF >75k hours with 90% confidence level at CR (excluding Panel) Temperature Operating (guaranteed performance according to spec requirements): 0 to 40 degree Storage - -20 to 60 ºC Shipping - -40 to 65 ºC...
Page 106: Regulatory Compliance
Per requirements. EMC Requirements Supplier DVT EMI test result must be submitted prior to DVT samples delivery, and PVT EMI test result must be submitted again prior to PVT samples delivery. Which also has to meet Philips' immunity testing specification. RoHS Restriction on the use of certain hazardous substances.
Page 107 221TE2L LCD General Product Specification Ongoing Regulatory There's a possibility that other regulatory certificates will be required during the life of the product. It is the responsibility of the supplier to provide related documentation. © MMD 2010 Page 44 of 45...
Page 108: General Product Specification
221TE2L LCD General Product Specification Distribution list Name Department Location © MMD 2010 Page 45 of 45...
Page 110: Spare/Recommended P Arts List
: 6K.0QC01.012 Panel+PCBA Styling Panel+PCBA Styling Model 9J.1BB72.*** 35PCS PN1 QN1 location Description PCM code Philips 12NC CPT AUO CPT AUO 5E.1BB01.011 MAIN (I/F) BOARD ASS'Y 5E.1BB01.001 POWER BOARD ASS'Y 5E.1BB02.001 CTRL BD ASS'Y 5E.1BB03.001 5E.1BB33.011 LED DRIVER BD ASS'Y 5E.1BB33.001...
Page 111: Pcba Photos
221TE2L LCD 111 Panel & PCBA photos ITEM PCM Description 5F.LTAPP.011 LCD21.5W CLAA215FA04 (CPT) ASSY LCDM21.5W M215Q01 V0 Z 6P.QUAV0.001 (QISDA) 5E.1BB01.011 MAIN (I/F) BOARD ASS'Y 5E.1BB01.001 MAIN (I/F) BOARD ASS'Y 5E.1BB02.001 POWER BOARD ASS'Y 5E.1BB03.001 ASSY CTRL BD+FFC CABLE 5E.1BB33.011 LED DRIVER BD 5E.1BB33.001...
Page 112: Repair Tips
112 221TE2L LCD 1.4 Attachment of SMDs 0. Warning - Locate the SMD on the solder lands by means of tweezers and solder the component on one side. Ensure that the component is positioned All ICs and many other semi -conductors are susceptible to correctly on the solder lands (see Fig.2A).
Page 113 IC data sheet. So as not to damage neighbouring components, it may be necessary to reduce some temperatures and times. More Information For more information on how to handle BGA devices, visit this URL: http://www.atyourservice.ce.philips.com (needs subscription). After login, select Magazine, then go to Workshop Information. Here you will find Information on how to deal with BGA-ICs.
Page 114: Repair Flow Chart
221TE2L LCD Repair Flow Chart No Display:...
Page 115 221TE2L LCD Repair Flow Chart Control board related: (Symptoms: particular key not responding.) 1. Check FFC cable connectivity. All buttons are no 2. Check PCB P/N to ensure correct board is response used. Board level analysis: Check ADC0/1/2 voltage level. Replace a new CTRL BD and test all keys again.
Page 116 221TE2L LCD Repair Flow Chart IR board does not work. (Symptoms: remote control not working.) All keys of remote control are not responding Ensure IR FFC cable and CTRL FFC is well inserted. Remote control issue Try another remote control check if IR responding May be IR BD issue , try another IR BD issue...
Page 117 221TE2L LCD Repair Flow Chart Power no work Start Check 7.5V Check 18V existed ? Power BD is OK Check F601 Replace F601 OK ? Check D701, Replace D701, D702 D702 OK ? Check Replace IC602, IC602,IC701 IC701 OK ? Check Replace Q601,R615 Q601,R615...
Page 118 221TE2L LCD Repair Flow Chart LED Driver no work Start Check Power BD Check Vin 18V existed ? Check ENA & Check I/F BD PWM signal is Check D801, Replace D801, L801 & Q801 L801 ,Q801 OK ? Replace IC601...
Page 119: Safety Test Requirements
221TE2L LCD 119 Safety Test Requirements 3. Equipments and Connection All units that are returned for service or repair must 3.1. Equipments pass the original manufactures safety tests. Safety For example : testing requires both Hipot and Ground Continuity - Zentech 9032 PROGRAMMABLE AUT O SAFETY testing.

This manual is also suitable for:

221te2lb/01

Philips 221TE2LB/00 Service Manual

Quick Links

TABLE OF CONTENTS

Troubleshooting

Related Manuals for Philips 221TE2LB/00

Summary of Contents for Philips 221TE2LB/00

This manual is also suitable for:

Table of Contents