Tsc Washing (Mod.sde); Tsc Quick Washing; Reset - Rancilio classe 10 Technical Manual

Keeping ''esc'' pressed for 2 seconds, during the
cycle the current washing phase will stop and the
next phase will take place.
It is advisable to always complete the rinsing cycle
to remove any detergent residues.
N.B. In the washing and rinsing phases the groups
are operated alternatively.
In any case the washing of the coffee groups can
be enabled whenever necessary according to the
previously described procedure.
3.4.2 TSC Washing (mod.DE)
At the set time, if the automatic washing mode is
enabled, a message on the display will request the
TSC washing.
Prepare a container with water and detergent to re-
move any milk. Insert the silicone pipe on the hose
holder, remove the nozzle and immerse it into the
container with detergent.
Immerse the lance into a half litre cold water bowl.
nd
Keep "-" button (2 button) pressed to start washing
until the display shows:
TSC Cleaning Cycle
Start cleaning cycle
TSC?
press <ENTER>
If "enter" is pressed within 10 sec.the following cycle
will be started (otherwise you will automatically exit
from this menu):
- the display will show:
TSC Cleaning Cycle
Prepare detergent
then press
press <ENTER>
- by pressing "enter" the cycle will be started and
the display will show:
CLEANING RUNNING
no.2 dispensing cycles are carried out as follows:
- steam dispensing start for 20 sec.
- pause for 2 sec.
At the end of the 2 cycles the display will show:
TSC Cleaning Cycle
Prepare clean water
then press
press <ENTER>
Immerse the silicone pipe into a clean water bowl
for rinsing. Replace the water of the bowl where the
lance is immersed with cold clean water.
By pressing "enter" the display will show
RINSE RUNNING"
and no.2 cycles will start as follows:
- steam dispensing start for 40 sec.
- pause for 2 sec.
42
Keeping ''esc'' pressed for 2 seconds, during the
washing cycle the current phase is stopped and the
next phase will take place.
It is advisable to always complete the rinsing cycle
to remove any detergent residues.
Rinsing phases cannot be avoided.
In any case the TSC washing can be enabled whene-
ver necessary according to the previously described
procedure.
If during the washing cycle the water where the lance
has been immersed exceeds 80°C, the message
below will be displayed
temperature
too high
and the current cycle will be interrupted.
In this case replace the water where the lance is
immersed with at least half litre of cold water and
press "enter" to continue the washing cycle.

3.4.3. TSC quick washing

If enabled, at the programmed interval the display will
show the message to carry out TSC quick washing
and both leds of TSC keys will flash.
Press one of the two keys to carry out quick washing
(steam dispensing for approx. 3 sec.)

3.5 Reset

Keeping pressed the key "+" and "-", at the same
time, switches on the machine, all the set data are
reset onto the program, and a few standard data
are automatically set (coffee dose, water dose, tank
pressure, etc.)
3.6. Timer
The Timer buttons are used to exclude the timed
switching ON and OFF of the machine.
When the timer function is selected, if the machine
is OFF, press the "Esc" buttons on the programming
keypad (for at least 3 second) to switch the machine
ON; the machine remains ON until the next timed
switching OFF or until you press the same controls
again (for at least 3 seconds).
When the timer function is selected, if the machine
is ON, press the "Esc" buttons on the programming
keypad (for at least 3 second) to switch the machine
OFF; the machine remains OFF until the next timed
switching ON or until you press the same controls
again (for at least 3 seconds).