Contents Dimensions ..........................2 Contents ............................ 3 Safety information ........................4 Product overview ........................7 Product description ........................ 7 Features at a glance ......................7 Product details ........................8 Quick Start ..........................9 Setting up ..........................9 Making fog ..........................9 Installation and setting up .......................
Do not spill fluid over or inside the machine. If fluid is spilled, disconnect AC power and clean with a damp cloth. If fluid is spilled onto electronic parts, take the system out of service and contact Martin for advice. Safety information...
Page 5
Do not remove the covers or attempt to repair a faulty machine. Refer any service not described in this manual to Martin. Do not operate the machine if any parts are damaged, defective or missing. Moisture and electricity do not mix. Do not aim fog output at electrical connections or devices.
Page 6
P r e ve n t i n g b r e at h i n g p r o b l em s A fog machine can operate safely only with the fog fluid it is designed for. Use the machine only with fluids specified under “Approved fluid types”...
P r o d u c t d e s c r i p t i o n The JEM ZR44 Hi-Mass™ is a reliable and highly efficient fogger capable of precise fog delivery from subtle to massive. Ideal for a variety of settings from...
P r o d u c t d e t a i l s Remove remote control to access Digital remote (accessory) socket. Remote control Main power switch Power inlet connector Dip switch 5 pin DMX 3 pin DMX AVR program (DMX address) input and input and...
Locate the machine in a suitably large area with nothing in front of the fog output. Fill the fluid tank with Martin approved fluid (see page 16). Connect the machine to a suitably rated power source. The power requirements are: EU Models - 1890 W, 220-240 V US Models –...
The fog machine may be located on the floor or may be suspended using the hanging bracket. If suspending the machine, a standard hanging clamp (available from Martin) should be attached to the machines hanging bracket with an M12 bolt and nyloc nut. Additionally, a secondary backup device, a safety cable (available from Martin) should be looped around the hanging bracket.
4 the fog fluid is one of the genuine Martin fluids listed under “Approved fluid types” on page 16 the machine is electrically grounded (earthed) ...
Control settings O v e r v i e w The unit is controlled using the remote control. You can control it in these ways: Manual firing by holding down the FOG button Automatic fog bursts using a repeating timer M a n u a l f i r i n g Hold down the FOG button.
Digital remote control O v e r v i e w A Digital Remote control, available separately, may be used for control of the JEM ZR44 HI-MASS™ Display XLR socket XLR socket (on rear) Timer button Fog button F u n c t i o n s The remote control provides the following functions: ...
DMX control O v e r v i e w DMX is a digital control system widely used in entertainment and architectural lighting. Any controller meeting the DMX-512 standard may be used to control and program the fog output of the fog machine. C o n n e c t i o n The fog machine provides both 3 &...
S e t t i n g t h e D M X a d d r e s s Each unit on a DMX system must be allocated an address so that the DMX controller can send separate commands to the unit. On the fog machine, the DMX address is set using the bank of switches (“dip switches”) on the back panel next to the DMX connectors.
Approved fluid types The following types of Martin fog fluid are approved for use in this machine. Each produces a different effect as described below. Martin supplies high quality fog fluids that are based on ultra-pure deionized water. Use only the following genuine Martin fog fluids.
Using Pro Clean Supreme every 200 hours, or once a month (depending on usage), will prolong the life of the heat exchanger in Martin fog and haze machines. Connect Pro Clean Supreme fluid to the fogger or hazer, then allow the unit to heat.
Remove the spent fuse and replace with one of exactly the same size and rating. The fuse type is indicated below. Contact Martin Service if the fuse blows repeatedly. US Model = 20AT (slow-blow), 125 V...
Troubleshooting Problem Probable cause(s) Suggested remedy Machine not at operating Wait 10 to 15 minutes temperature Machine will not produce fog Ensure mains power switch Machine not powered up or when remote control Fog on, enable heaters by heaters disabled button pressed...
Technical Specifications P h ys i c a l Length ..................687 mm (27.1 in.) Length with optional drip tray ............752 mm (30 in.) Width ....................379 mm (15 in.) Height .................... 248 mm (9.8 in.) Height with hanging bracket ............353 mm (13.9 in.) Weight, dry ..................
Page 21
JEM™ i-fog Fluid JEM™ Pro Steam Simulation Fluid JEM™ Pro Clean Supreme Fluid *Various sizes available - contact your dealer or see martin.com for more details. Installation Hardware Half-coupler clamp ................P/N 91602005 G-clamp (vertical hanging suspension only) ........P/N 91602003 Quick trigger clamp (vertical hanging suspension only) ....
Page 22
Specifications subject to change without notice. For the latest technical specifications, see www.martin.com Technical Specifications...
Page 26
Parliament and of the Council of the European Union on WEEE (Waste Electrical and Electronic Equipment), as amended by Directive 2003/108/EC, where applicable. Help preserve the environment! Ensure that this product is recycled at the end of its life. Your supplier can give details of local arrangements for the disposal of Martin products.
Page 28
Martin Professional A/S,Olof Palmes Allé 18, DK-8200,Aarhus N Phone: +45 87 40 00 00 Internet: www.martin.com...