Banner Q4X Quick Start Manual
Stainless steel analog laser sensor
Hide thumbs
Also See for Q4X:
- Instruction manual (46 pages) ,
- Quick start manual (14 pages) ,
- User manual (2 pages)
Table of Contents
Advertisement
Q4X Stainless Steel Analog Laser Sensor
Quick Start Guide
Class 1 laser CMOS analog sensor with an analog output. Patent pending.
This guide is designed to help you set up and install the Q4X Analog Sensor. For complete information on programming,
performance, troubleshooting, dimensions, and accessories, please refer to the Instruction Manual at
www.bannerengineering.com. Search for p/n 185624 to view the Instruction Manual. Use of this document assumes
familiarity with pertinent industry standards and practices.
For illustration purposes, the threaded barrel model Q4X images are used throughout this document.
WARNING: Not To Be Used for Personnel Protection
Never use this device as a sensing device for personnel protection. Doing so could lead to
serious injury or death. This device does not include the self-checking redundant circuitry necessary
to allow its use in personnel safety applications. A sensor failure or malfunction can cause either an
energized or de-energized sensor output condition.
Features
1
Figure 1. Sensor Features—Threaded Barrel
Models
Display and Indicators
The display is a 4-digit, 7-segment LED. The main screen is the Run Mode screen, which shows the current distance to the
target in millimeters.
Figure 3. Display in Run Mode
Output Indicator
•
On—Displayed distance is within the taught analog
output window
•
Off—Displayed distance is outside of the taught
analog output window
Active TEACH Indicators (2PT and 1PT)
•
2-PT on—Two-point TEACH mode selected (default)
•
1-PT on—One-point TEACH mode selected
Original Document
185623 Rev. D
2
1. Output Indicator (Amber)
3
2. Display
3. Buttons
1. Stability Indicator (STB = Green)
2. Active TEACH Indicators
3. Display Value Indicator (MM = Amber)
7 September 2016
Figure 2. Sensor Features—Flush Mount
•
2-PT = Two-Point TEACH (Amber)
•
1-PT = One-Point TEACH (Amber)
Stability Indicator (STB)
•
On—Stable signal within the specified sensing range
•
Flashing—Marginal signal, the target is outside of
the limits of the specified sensing range, or a
multiple peak condition exists
•
Off—No target detected within the specified sensing
range
Display Value Indicator (MM)
•
On—Display shows the distance in millimeters
(default)
•
Off—Display shows the analog output value
1
2
3
Models
185623
Advertisement
Table of Contents
Related Manuals for Banner Q4X
Summary of Contents for Banner Q4X
- Page 1 Class 1 laser CMOS analog sensor with an analog output. Patent pending. This guide is designed to help you set up and install the Q4X Analog Sensor. For complete information on programming, performance, troubleshooting, dimensions, and accessories, please refer to the Instruction Manual at www.bannerengineering.com.
-
Page 2: Laser Description And Safety Information
Pulse Duration: 7 µs to 2 ms Installation Install the Safety Label The safety label must be installed on Q4X sensors that are used in the United States. NOTE: Position the label on the cable in a location that has minimal chemical exposure. -
Page 3: Sensor Orientation
Q4X Stainless Steel Analog Laser Sensor Sensor Orientation Optimize detection reliability and performance with correct sensor-to-target orientation. To ensure reliable detection, orient the sensor as shown in relation to the target to be detected. Figure 5. Optimal Orientation of Target to Sensor See the following figures for examples of correct and incorrect sensor-to-target orientation as certain placements may pose problems for sensing some targets. -
Page 4: Cleaning And Maintenance
Q4X Stainless Steel Analog Laser Sensor NOTE: The input wire function is user-selectable; see the Instruction Manual for details. The default for the input wire function is off (disabled). NOTE: Shielded cordsets are recommended for all models with quick disconnect fittings. It is recommended that the shield wire be connected to -V dc (the blue wire). - Page 5 Q4X Stainless Steel Analog Laser Sensor Top Menu Sub Menus Teach Process Selection two-point teach default setting) one-point teach Base Measurement Rate set Base Measurement Rate to 0.3 ms set Base Measurement Rate to 0.5 ms set Base Measurement Rate to 1.0 ms set Base Measurement Rate to 2.5 ms...
-
Page 6: Basic Teach Instructions
Q4X Stainless Steel Analog Laser Sensor Basic TEACH Instructions Use the following instructions to teach the Q4X sensor. The instructions provided on the sensor display vary depending on the type of TEACH mode selected. Two-point TEACH is the default TEACH mode. -
Page 7: Specifications
Performance Curves—Flush Mount Models on page 9). Output Rating Response Speed Analog Voltage Outputs (Q4X..U Models): 2.5 kOhm minimum load Total response speed varies from 0.5 ms to 2560 ms, depending on resistance base measurement rate and averaging settings. Analog Current Outputs (Q4X..I Models): 1 kΩ maximum load See Instruction Manual for more information. -
Page 8: Performance Curves-Threaded Barrel Models
Q4X Stainless Steel Analog Laser Sensor Required Overcurrent Protection Certifications WARNING: Electrical connections must be made by qualified personnel in accordance with local and national electrical codes and regulations. Class 2 power Industrial Control Equipment UL Environmental Rating: Type 1... -
Page 9: Performance Curves-Flush Mount Models
Q4X Stainless Steel Analog Laser Sensor Temperature Effects 0.35 0.30 0.25 0.20 0.15 0.10 0.05 DISTANCE (mm) Performance Curves—Flush Mount Models Accuracy (90% to 6% reflectance) 1.25 1.00 0.75 0.50 0.25 DISTANCE (mm) DISTANCE (mm) Figure 15. 110 mm Models Figure 16. - Page 10 Banner Engineering Corp. Limited Warranty Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period.