Automatic Relay Activation Time Zone Programming (Up To 4); Access Code Time Zone Programming (Up To 4) - DKS 1812 Access Plus Installation & Owner's Manual

2.7.5 Automatic Relay Activation Time Zone Programming (Up to 4)

Factory setting in step 3 is 0 (Time zones are OFF).
This program sequence sets up time zones to automatically activate and deactivate relays 1 through 8. Four time zones can
be programmed, each of which can be assigned to the desired relay(s). These time zones can be independently turned ON
or OFF after they have been programmed.
1. Press
*
2. Enter a time zone number (1, 2, 3 or 4), then press
3. Press 0
here (Go to step 11 to finish) if you have previously programmed the time zones and only ON / OFF is desired.
4. Enter the beginning hour (01 to 12) and minutes (01 to 59), then press
5. Press 0
6. Enter the ending hour (01 to 12) and minutes (01 to 59), then press
7. Press 0
8. Enter the days of the week that the auto relay time zone is to be active, then press
Sun =1, Mon = 2, Tue = 3, Wed = 4, Thu = 5, Fri = 6, Sat = 7.
You can enter up to 7 numbers here (1-7) but all 7 spaces do not have to be populated with numbers. For
example, for the auto relay time zone to be active only on Saturdays and Sundays, enter 1 7
numbers is not important; 17 is the same as 71.
9. Enter the relay number(s) that the time zone will apply to, then press
You can enter a single relay number; all relay numbers (up to 8), or any combination of relay numbers.
10. Repeat steps 2 through 9 to program the other auto relay time zones (up to 4) if desired.
11. Press 0 # TOGETHER to end. [0 # (beeeeeep)]

2.7.6 Access Code Time Zone Programming (Up to 4)

Factory setting in step 3 is 0 (Time Zones are OFF).
This programming sequence sets up time zones (up to 4) that can be applied to the "Access Codes" programmed in
section 2.6.4 into the 1812. These time zones can be turned ON or OFF once they have been programmed.
1. Press
*
2. Enter a time zone number (3, 4, 5 or 6), then press
Do not use 0, 1 or 2 for time zone numbers. These are already used; 0 = always deny,
1 = 24/7 access for Relay 1, and Relays 3-8; 2 = 24/7 access for Relay 2, and Relays 3-8.
3. Press 0
You can terminate here (Go to step 11 to finish) if you have previously programmed the time zone and
only ON / OFF is desired.
4. Enter the beginning hour (01 to 12) and minutes (01 to 59), then press
5. Press 0
6. Enter the ending hour (01 to 12) and minutes (01 to 59), then press
7. Press 0
8. Enter the days of the week that the time zone is to be active, then press
Sun =1, Mon = 2, Tue = 3, Wed = 4, Thu = 5, Fri = 6, Sat = 7.
You can enter up to 7 numbers here (1-7) but all 7 spaces do not have to be populated with numbers.
For example, for the time zone to be active only on Saturdays and Sundays, enter 1 7
the numbers is not important; 17 is the same as 71.
9. Enter the relay number(s) that the time zone will apply to, then press
You can enter a single relay number; all relay numbers (up to 8), or any combination of relay numbers.
10. Repeat steps 2 through 9 to program the other time zones (up to 4) if desired.
11. Press 0 # TOGETHER to end. [0 # (beeeeeep)]
1812-162-V-5-16
3 5 and enter the MASTER CODE. [
to turn the time zone OFF, OR press 1
*
for AM OR press 1 for PM. [ _
* *
for AM OR press 1 for PM. [ _
* *
3 6 and enter the MASTER CODE. [
to turn the time zone OFF, OR press 1
*
for AM OR press 1 for PM. [ _
* *
for AM OR press 1 for PM. [ _
* *
3 5 _ _ _ _ (beep)]
*
. [ _ (beep)]
* *
to turn the time zone ON. [ _
*
(beep)]
*
*
(beep)]
*
*
3 6 _ _ _ _ (beep)]
*
. [ _ (beep)]
* *
to turn the time zone ON. [ _
*
(beep)]
*
*
(beep)]
*
*
(beep)] You can terminate
*
. [ _ _ _ _ (beep)]
* *
. [ _ _ _ _ (beep)]
*
. [ _ _ _ _ _ _ _
*
. The order of the
*
. [ _ (beep)]
*
(beep)]
*
. [ _ _ _ _ (beep)]
* *
. [ _ _ _ _ (beep)]
*
. [ _ _ _ _ _ _ _ (beep)]
* *
. The order of
*
. [ _ (beep)]
*
(beep)]
*
39