Wire One 1812 To The Internet - Telephone Mode - DKS 1812 Access Plus Installation & Owner's Manual

1.7 Wire One 1812 to the Internet - Telephone Mode

Typical "Existing"
Internet Source
Internet
Internet
DSL/Cable
Modem
Router
RJ-11
Phone
Connector
TIP (+): White/blue mark
RING (-): Blue/white mark
Phone
Jack
Access Control Devices
"Normally Open"
Vehicular
Gate Operator
Use minimum 18
AWG wire for runs
up to 100 feet.
W A
R N
IN
G
MO
SER VIN G 16 AWG wire for
Oper IOU GA S INJ TE
and free ate gate UR CAN
Do of peop only when Y OR CAU SE
or not oper allow le and gate DEA TH
Do not ate gate. child ren obstr area uctio is
path while stand play to ns. sight in
Read owne gate in is gate path in gate area
man r's movi ng. or walk
ual and throu gh
safet y instr
uctio
ns.
CON FOR runs up to 200 feet.
ANS I/UL MS TO
CAN /CSA CER TIFI -325
VEH C22 ED TO
CLA ICU LAR NO. .2 53382
SS GAT 247
MOD E OPE
SER EL RAT OR
IAL HP
VOL TS
AMP
MAX S
GAT PHA SE
Door E LOA D 60
King , Inc., Hz
Ingle (Term. 11 and 13)
woo d,
CA
Pedestrian
Gate/Door
"Normally Close" with Maglock
(Terminal 15 and 16)
"Normally Open" with Electric Strike
(Terminal 14 and 16)
Magnetic locks or electric strikes must be
powered from a separate UL Listed power
transformer. DO NOT power strikes or magnetic
locks from the 1812 power transformer. Use
minimum 18 AWG wire for runs up to 100 feet;
16 AWG wire for runs up to 200 feet. It is
recommended to keep power wire runs as short
as possible.
1812-162-V-5-16
Single 1812 Wiring Configuration
EARTH
GND
1 2
CENTRAL
Internet OFFICE
Phone In
Phone In
Phone Mode
4 4 5 5 6 6
7 7 8 8 9 9
0 0
Phone Out
"Existing" Alarm
System Location
RJ31x
Phone Jack
installed
Before 1812
System
To "Existing"
Alarm Control Panel
Separate UL
Listed Power
Transformer
Electric
Strike
The 1812 Access Plus operates ONLY
on 16.5 VAC. DO NOT power the 1812
with 24 Volt transformer or source
voltage. Use the supplied power
transformer, 16.5 VAC, 20 VA (or UL
listed equivalent) to power the
telephone entry system. DO NOT power
any other devices (electric strikes,
magnetic locks, additional 1812s etc.)
from the 1812's power transformer.
See page 13 for wire size and run
distances.
The By-Pass board is NOT optional and
ENTRY BY-PASS
must be installed as part of the 1812
SW1
1875-010
"Telephone Mode" system.
See page 11 for complete information.
3 4 5 6 7 8
PHONE PHONE
HOME
Single 1812:
IN OUT
Homeowner's
Phone
Phone
PHONE IN #3 connects to Main Term #1.
Out
LAN/Cordless
PHONE IN #4 connects to Main Term #2.
PHONE OUT #5 connects to Main Term #5.
PHONE OUT #6 connects to Main Term #4.
EARTH
GND
Telephone Line (Cat5e)
For complete information,
see page 12.
Cat5e
Be sure to properly ground
ALL boards. See page 13
for acceptable grounding
sources.
Ground
12 AWG Min.
Orange Pair
Supplied Transformer
Polarity does not matter.
t
t p u
O u
C
V A
. 5
1 6
V A
2 0
OUT OUT
OUTPUT
LOW VOLTAGE LINE
Ground
12 AWG Min.
Within 3 ft
of Surge Board
1878-010
By-Pass Board
ENTRY BY-PASS
SW1
1875-010
1 2 3 4 5 6 7 8
CENTRAL PHONE PHONE
HOME
OFFICE IN OUT
Orange Green
Pair Pair
Older Lines
Ground
Red Wire (-)
12 AWG Min.
Older Lines
Green Wire (+)
Main
Terminal
J1 J1
1 Phone In
RING
(1-2)
2
TIP
3
GND
4
TIP Phone Out
(4-5)
5
RING
Green Pair
6
7
1970-010
8
9
10
11
N.O.
Relay 1
12
N.C.
(11-13)
13
Com
14
N.O.
Relay 2
15
N.C.
(14-16)
16
Com
Power
17
16.5
VAC
18 (17-18)
OV
Low Voltage Surge Suppressor
DoorKing Surge Suppressor P/N 1878-010 (or
GND GND IN IN
equivalent) is optional but highly recommended.
INPUT
For best protection, surge suppressor ground wire
MUST be 3-ft. or less in length. Use minimum 12 AWG
wire. Refer to instruction sheet included with surge
board for complete information.
Check Polarity of
Telephone Line
Check for polarity on the
incoming telephone line to each
board and maintain polarity
throughout the telephone line.
One potential problem checked
when a malfunction occurs in a
telephone entry system is to
see if the telephone line has
been wired to each board with
the correct polarity.
Test Example: By-pass board's
CENTRAL OFFICE terminals #1
and #2. Terminal #2 must be
positive (Tip +) with respect to
terminal #1 (Ring -). Set a VOM
meter to measure DC volts.
Place the positive lead on
terminal #2 and the negative
lead on terminal #1. If the
meter shows a positive voltage
- OK. If the meter shows a
negative voltage (needle moves
off scale to the left), reverse the
wires on terminals #1 and #2.
Homeowner's
LAN/Cordless Phones
RING
TIP
Phone Phone
Jack Jack
J4
1
2
3
4
5
6
7
8
Note: Each relay can control a
normally open OR normally close
access control device. Relay
contacts are rated for 3 amps @
30 VAC maximum.
15