Answer Incoming Call On X Rings; Call Waiting; Turn Speaker On / Control Relay From Off-Site Call - DKS 1812 Access Plus Installation & Owner's Manual

2.4.9 Answer Incoming Call on X Rings

Factory setting is 06 (6 Rings).
This programming section sets the number of rings that the 1812 will allow to pass through the system before it picks up
the call. The number of rings to answer can be set from 1 to 99 rings and must be entered as a two-digit number.
For example, if you want the 1812 to answer the call after the sixth ring, enter 0 6
2, this will prevent (disable) the 1812 from answering incoming calls to it.
Important! If more than one 1812 is connected in the system (2.4.2 set for multiple systems), the LAST 1812 that is wired
in the line must have the "Answer Incoming Call" set for one less ring than the other 1812 units connected.
1. Press
2. Enter the number of rings (01-99), then press
3. Press 0 # TOGETHER to end. [0 # (beeeeeep)]
Example:
Answering:
Homeowner's
Phone

2.4.11 Call Waiting

Factory setting is 1 (Call Waiting On).
These steps will turn the Call Waiting feature either ON or OFF. The call waiting feature will allow the resident to place an
outside call on hold when a visitor presses the call button on the 1812. Once communication with the visitor is established,
access can be granted or denied. If access is granted (press the tone open number to open the door or gate), then press #
to switch the call back to the outside call. If the resident wants to deny access, they simply press the # key to switch back
to the outside call.
1. Press
2. Press 1
3. Press 0 # TOGETHER to end. [0 # (beeeeeep)]

2.4.12 Turn Speaker On / Control Relay from Off-Site Call

This command allows you to call the 1812 from a remote location and turn on the speaker at the unit to enable two-way
voice communication and will allow relay control – all "Tone Open Numbers" that are programmed (2.4.8).
1. Call the resident's phone number. After the programmed number of rings (2.4.9) the 1812 will answer
with a tone.
2. Press
If you use a "tone open number" during the call to activate a relay, the 1812 will automatically hang up
after the "tone open number" is used. Only one activation number will function per phone call.
Example: If you call and want to "Hold Open" the relay, you will have to call back to "Deactivate" it later.
3. Hang up when your conversation is completed when NOT using a "tone open number".
34
1 8 and enter the MASTER CODE. [
*
(enter 00 in this step to disable this feature)
Machine/
3 3 3 3 3 3 3 3 3
4 4 5 5 6 6
Service
7 7 8 8 9 9
0 0
4 Rings
4th 1812
5 Rings
2 0 and enter the MASTER CODE. [
*
to turn Call Waiting ON OR press 0
*
1 6 and enter the MASTER CODE. [
*
*
1 8 _ _ _ _ (beep)]
*
. [ _ _ (beep)]
* *
1 1 1 1 1 2 2 2 2 2 3 3 3 3 3 3 3 3 3
4 4 5 5 6 6 4 4 5 5 6 6
7 7 8 8 9 9 7 7 8 8 9 9
0 0 0 0
3rd 1812 2nd 1812
6 Rings 6 Rings
2 0 _ _ _ _ (beep)]
*
to turn Call Waiting OFF. [ _
*
1 6 _ _ _ _ (beep)]
*
in step 2. If you program 0 0
4 4 5 5 6 6
7 7 8 8 9 9
0 0
1st 1812
6 Rings
(beep)]
*
in step
*
Central
Office
Line
1812-162-V-5-16