Canon iPF760 series Service Manual page 316

Chapter 8
Display message
Paper loaded askew.
Lift the release lever.
Ink tank cover is open.
Turn off printer, wait a while, and turn it
on again.
Carriage Cover is open.
Turn off printer, wait a while, and turn it
on again.
Rel lever is in wrong position.
Turn off printer, wait, then turn on again.
Rel lever is in wrong position.
Turn off printer, wait, then turn on again.
Top cover is open.
Turn off printer, wait a while, and turn it
on again.
! Unable to detect ink level correctly.
! Paper mismatch
Make sure media type and paper size
match for the adjustment print.
Sheet printing is selected.
Press Load/Eject and load sheets.
Sheet printing is selected.
Press Load/Eject and load sheets.
Sheet printing is selected.
Press Load/Eject and load sheets.
Sheet printing is selected.
Press Load/Eject and load sheets.
Cassette printing is selected.
Press Load/Eject and remove manually
Roll printing is selected.
Press Load/Eject and load a roll.
Roll printing is selected.
Press Load/Eject and load a roll.
PaprWidth Mismatch
Plain Paper
ISO A3
Online=Print
Stop=Stop Printing
No Roll Feed Unit.
Turn printer off and install roll feed unit.
The roll is empty.
Lift the release lever and replace the roll.
Roll feed unit err
Turn off printer and check roll feed unit
Roll Paper
Plain Paper
ISO A3
Load Roll Paper
Stop Printing
! Roll2 (Lower) printing is selected.
Press Load/Eject and load a roll.
Roll printing is selected.
Press Load/Eject and load a roll.
! Roll 1 (Upper) printing is selected.
Press Load/Eject and load a roll.
! Roll printing is selected.
Press Load/Eject and load a roll.
8-6
Code* Condition detected
03016000-2010 Skew
03031000-2E10 Ink tank cover abnormally open
03031000-2E11 Printhead cover open
03031000-2E12 Release lever open
03031000-2F21 Pinch roller open error
03031000-2F38 Top cover abnormally open
03031101-25B7 With ink tank cover open, ink has
diminished below the pin check level.
During printing with ink tank cover open,
the ink has diminished below the pin check
level.
*Under study as a part of stop-less supply
system. This error is intended for
preventing the ink tank to be installed in
other model (iPF710) using the same ink
tank by the hardware configuration that
disables writing to ink tank EEPROM
while ink tank cover is open.
03060000-2E20 Paper type mismatch at adjustment
03060100-2E02 After starting to print sheet, no manual
feeding paper has been detected.
03060100-2E04 No front manual feed paper
03060100-2E05 After starting to print sheet, no manual
feeding paper has been detected.
03060200-2E03 No cassette paper
03060200-2E0B After manual feed cut sheet had been
loaded, data with cassette specification was
received.
03060A00-2E00 Data with a roll media specification has
been received but no roll media are loaded.
03060A00-2E01 No roll paper at internal printing
03060A00-2E08 Paper width mismatch
03060A00-2E0E Roll media unit not installed.
03060A00-2E1B Roll media end
03060A00-2E24 Roll cam sensor error
03060A00-2E33 Roll media is not loaded when receiving
the printing job.
Roll paper is not loaded when a job with
roll paper specification has been received.
03060A00-2E34 Roll paper is not loaded. (lower roll)
03060A00-2E35 Roll media is not loaded for internal
printing.
03060A00-2E37 Roll paper is not loaded. (upper roll)
03060B00-2E36 Roll media is not loaded for internal
printing. (lower roll)
Action
Correct the skew in the paper and reload it.
Close the ink tank cover and turn on the printer again.
Close the carriage cover and turn off the printer, and turn
it on again.
Close the release lever and turn off the printer, and turn
it on again.
Check the pinch roller unit and surrounding part.
Close the top cover and turn on the printer again.
By closing the ink tank cover, this warning is cleared.
If the pin check tank is removed in this condition, the
error changes to the pin check tank removal error. Or, if
printing is continued in this condition, and the subtank
corresponding to the pin check tank is detected empty,
the error changes to the subtank corresponding to pin
check tank empty error.
Choose the same paper type as the first page and
perform adjustment printing.
Load cut sheet in manual feeding slot.
Load cut sheet in the front manual feed paper slot.
Load cut sheet in manual feeding slot.
Load cut sheet in the cassette.
Load cut sheet in the cassette.
Load roll media.
Load roll media.
Check the paper width and print.
Install the roll media unit.
Renew the supply of roll media.
Check the roll paper unit.
(1) Choose [Load Roll Paper] and load paper according
to the panel guidance.
(2) Choose [Stop Printing] or press the Stop button to
stop printing.
(3) Lift the release lever, and load paper.
(1) Choose [Load Roll Paper] and load paper according
to the panel guidance.
(2) Choose [Stop Printing] or press the Stop button to
stop printing.
(3) Lift the release lever, and load paper.
Reload the roll media.
(1) Choose [Load Roll Paper] and load paper according
to the panel guidance.
(2) Choose [Stop Printing] or press the Stop button to
stop printing.
(3) Lift the release lever, and load paper.
Load the roll media.