Canon iPF760 series Service Manual page 56

A4- to a0-size
Hide thumbs Also See for iPF760 series:
Table of Contents

Advertisement

Chapter 1
[GL2 Settings] [Quality
Manager]
[Paper
Manager]
[Line & Pen
Manager]
[ProcessingOp
tion]
[GL2 Set Print]
1-42
Setting Item
[Color Mode] [Monochrome]
[Color (CAD) 1]
[Color (CAD) 2]
[Color (CAD) 3]
[Color (CAD) 4]
[Color (CAD) 5]
[Print Quality]
[Input Resolution]
[Print (Economy)]
[Paper Source]
[Margin]
[Conserve Paper]
[Auto Rotate]
[Nesting]
[Use Nesting]
[Nesting
WaitTime]
[Cut Lines]
[Enable merge]
[Pen Setup]
[Select Palette]
[Define Palette]
[Reset Palette]
[Smoothing]
[ThickenFineLines]
[AdjustFaintLines]
[Warning]
[On-the-Fly]
[PageSizeProcess1]
[PageSizeProcess2]
Description/Instructions
Print by the monochrome.
Print by the standard color.
Print by the bright color.
Print by the color emulated the Canon iPF500/iPF600/iPF700/iPF510/iPF610/iPF710/iPF605/
iPF720/iPF810/iPF820.
Print by the color emulated the HP Designjet 500/800.
Print by the color emulated the HP Designjet 1000.
Select the print quality.
Choose the printer input resolution from between [600dpi] and [300dpi].
Prints with a lower grade of print than normal, but with less ink consumption. Select [ON] to
economize on inks.
Select how to feed paper for printing on the HP-GL/2.
Set the top/bottom and left/right margins of the paper. For cut-sheet, the trailing edge margin
is 23mm.
However, if the leading edge margin is set with [Paper Details], that value has priority.
Prints by economizing on paper.
If a document has its long side shorter than the roll width, the page rotates by 90 degrees
automatically to economize on paper. If a document contains horizontally long data such that
it has its long side longer than the roll width and its short side shorter than the roll width, the
page rotates 90 degrees to print within the boundaries of the paper.
HP RTL cannot rotate.
In case of HP RTL image, the image may be truncated or a blank paper may be ejected because
the image cannot be rotated even if the paper size is rotated by 90 degrees. In that case, set
[Auto Rotate] to [Off].
Select [On] to print pages when they are tiled fully to the roll width, instead of printing them
one by one.
Set the time to elapse before printing.
Select [On] to print perforated lines between pages.
When lines overlap, set whether to merge or overwrite the colors of the overlapping lines.
Select [Off] to overwrite with the line printed later. Select [On] to merge all overlapping colors.
Select the value related to pen from [Software], [Palette A], [Palette B], or [Factory].
Select [Software] to print according to the application side instruction. Select [Palette A] or
[Palette B] to print with value set by [Define Palette].
Set [Width], [Color], and [Line Attributes] for the palette's [Pen Number]. Select [Factory] to
check the value when [Factory] is selected for [Select Palette].
For [Line Attributes], select the shape of line end and joint between lines as [No Setting] or
[Circle Setting].
Return the [Define Palette] settings to factory settings.
Choose whether to draw an arc with a smooth curve or with a polygon.
Select [On] to print thin lines clearly.
If thin lines print in a tint of color varied from other patterns, selecting [Off] may provide the
print result as intended, though the thin lines may print, interrupted, depending on the color.
Select [On] to display warnings during GL2.
In printing data consisting solely of HP RTL, if the data is slow to print, select [On] to expedite
the time at which the data starts printing. Verify the print result to make sure that images are
not chipped in this case.
Normally, an image is printed inside margins necessary for printing, but if the image data itself
has margins, the print position will not be offset when this is set [On].
Select [On] to determine the paper size based on the drawing area.
Print the GL2 settings.

Advertisement

Table of Contents

Troubleshooting

loading

This manual is also suitable for:

Ipf750 series

Table of Contents