Table of Contents
Advertisement
7
Reboot the host computer.
8
If sled(s) or drive(s) are physically missing from
the array, the entire stripe group (LUN)
containing the drive(s) will be unavailable. To
determine which drives would be unavailable in
various configurations, see Exhibit 6.2-1 and
Exhibit 6.2-2.
To remove RAID Level 0 groups
1
Connect to the array via the RS-232 port or the
optional Ethernet management services card
Exhibit 6.2-1 Sled-based QuickRAID0 stripe groups with LUN designations in a fully populated Array set up as
QuickRAID0 6 sled. If sled 6 were to be withdrawn from the array, LUN 3 (grayed boxes) would be unavailable.
Physical Sled
1
2
Physical Drive
1
2
1
JBOD
1
1
1
1
2
1
1
1
3
1
1
1
4
1
1
1
6
1
1
1
12
1
1
2
Exhibit 6.2-2 Drive-based QuickRAID0 stripe groups with LUN designations in a fully populated Array set up as
QuickRAID0 6 Drive. If sled 6 were to be withdrawn from the array, LUNs 2 and 5 would be unavailable.
Physical Sled
1
2
Physical Drive
1
2
1
JBOD
0
1
13
2
1
1
1
1
2
1
2
1
3
1
2
1
4
1
3
1
6
1
4
1
12
1
7
1
54
Diamond Storage Array
3
4
5
2
1
2
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
2
2
2
1
2
2
2
2
3
2
3
3
4
4
5
LUNs: virtual drive numbers
3
4
5
2
1
2
1
2
1
14
3
15
4
16
5
1
1
1
1
1
1
2
1
2
1
2
1
2
1
2
1
2
1
3
1
3
1
3
1
4
1
4
1
4
2
7
2
8
2
8
3
LUNs: virtual drive numbers
Accessing the Array
(refer to
should now be in CLI.
1
Continue with the CLI or access the RAID page
of the ExpressNAV interface (refer to
ExpressNAV: Browser-based Interface
2
Type set QuickRAID0 0 to configure the array
in JBOD mode.
3
Continue with steps 4 through 7 of
RAID Level 0 groups
6
7
2
1
2
1
2
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
4
4
4
5
6
6
7
7
8
6
7
8
2
1
2
1
2
1
17
6
18
7
19
8
1
1
1
1
1
1
2
1
2
1
2
1
3
1
3
1
3
1
3
1
3
2
4
2
5
2
5
2
5
2
9
3
9
4
10
4
on page 17). You
on page 53.
8
9
10
2
1
2
1
2
1
1
1
1
1
1
1
2
2
2
2
2
2
2
3
3
3
3
3
3
3
3
4
4
4
4
5
5
5
5
6
8
9
9
10
10
11
9
10
2
1
2
1
2
1
20
9
21
10
22
11
1
1
1
1
1
1
2
1
2
1
2
1
3
2
3
2
3
2
4
2
4
2
4
2
5
3
6
3
6
3
10
5
11
5
11
6
ATTO
on page 25).
To set up
11
12
2
1
2
1
1
1
2
2
2
3
3
3
4
4
4
6
6
6
11
12
12
11
12
2
1
2
23
12
24
1
1
1
2
1
2
3
2
3
4
2
4
6
3
6
12
6
12
Advertisement
Table of Contents
Need help?
Do you have a question about the Diamond Storage Array S-Class and is the answer not in the manual?