1. Manuals
  2. Brands
  3. Eiki Manuals
  4. Projector
  5. EIP-3500
  6. Service manual

Eiki EIP-3500 Service Manual

Hide thumbs Also See for EIP-3500:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Owner's Manual, Setup Manual
In the interests of user-safety (Required by safety regulations in some countries) the set should be re-
stored to its original condition and only parts identical to those specified should be used.

SERVICE MANUAL

DLP
MODEL
This document has been published to be used for
after sales service only.
The contents are subject to change without notice.
TM
PROJECTOR
EIP-3500
EIP-3500
S04A7XG-MB70X

Advertisement

Table of Contents
loading

Related Manuals for Eiki EIP-3500

Summary of Contents for Eiki EIP-3500

  • Page 1: Service Manual

    EIP-3500 SERVICE MANUAL S04A7XG-MB70X PROJECTOR EIP-3500 MODEL In the interests of user-safety (Required by safety regulations in some countries) the set should be re- stored to its original condition and only parts identical to those specified should be used. This document has been published to be used for after sales service only.

  • Page 2: Table Of Contents

    EIP-3500 CONTENTS Page Page • SPECIFICATIONS ..........3 • BLOCK DIAGRAM .......... 50 • IMPORTANT SERVICE SAFETY • OVERALL WIRING DIAGRAM ......52 NOTES .............. 4 • WAVEFORMS ..........54 • NOTE TO SERVICE PERSONNEL ....6 • PRINTED WIRING BOARD ASSEMBLIES ..55 •...

  • Page 3: Specifications

    (TINS-B671WJZZ (English), TINS-B672WJZZ (French), TINS-B673WJZZ (Spanish), TINS-B674WJZZ (Italian), TINS-B675WJZZ (German), TINS-B676WJZZ (Portuguese)) As a part of policy of continuous improvement, EIKI reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some...

  • Page 4: Important Service Safety Notes

    EIP-3500 IMPORTANT SERVICE SAFETY NOTES (for USA) Ë Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and servicing guidelines as follows: » Use an AC voltmeter with sensitivity of 5000 ohm per WARNING volt., or higher, sensitivity to measure the AC voltage...
  • Page 5 EIP-3500 PRECAUTIONS A PRENDRE LORS DE LA REPARATION Ë Ne peut effectuer la réparation qu' un technicien spécialisé qui s'est parfaitement accoutumé à toute vérification de sécurité et aux conseils suivants. AVERTISSEMENT conduite électrique ou une prise de terre branchée à la 1.

  • Page 6: Note To Service Personnel

    EIP-3500 NOTE TO SERVICE NOTE POUR LE PERSONNEL PERSONNEL D’ENTRETIEN 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6...

  • Page 7: Lamp Replacement

    EIP-3500 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6...

  • Page 8: Power Unit

    EIP-3500 WARNING: High brightness light source, do not stare into the beam of light, or view directly. Be especially careful that children do not stare directly in to the beam of light. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO MOISTURE OR WET LOCATIONS.
  • Page 9 EIP-3500 Precautions for using lead-free solder 1 Employing lead-free solder "PWBs" of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the PWBs and service manuals. The alphabetical character following LF shows the type of lead-free solder.

  • Page 10: Operation Manual

    EIP-3500 Operation Manual Projector Top View POWER button Power indicator For turning the power on or putting the projector into Lamp indicator standby mode. Temperature warning indicator KEYSTONE button For entering the Keystone Volume buttons Correction mode. For adjusting the speaker sound level.

  • Page 11: About The Indicators On The Projector

    EIP-3500 About the Indicators on the Projector Power indicator Green on ... Normal (Standby) Red on ... Normal (Power on) Lamp indicator Green on ... Normal Green blinks ... The lamp is warming up or shutting down. Red on ... The lamp has been shut down abnormally or needs to be changed.
  • Page 12 EIP-3500 Projector (Rear View) Terminals Refer to “INPUT/OUTPUT Terminals and Connectable Main Equipment” on INPUT 3 terminal AUDIO OUTPUT terminal Terminal for connecting Audio output terminal of video equipment. equipment connected to the AUDIO INPUT terminal. INPUT 4 terminal Terminal for connecting...

  • Page 13: Remote Control

    EIP-3500 Remote Control POWER button AUTO FOCUS button For turning the power on or For adjusting the focus putting the projector into automatically. standby mode. FOCUS buttons For bringing the projected image ZOOM buttons into focus. For adjusting the projected IRIS button image size.

  • Page 14: Usable Range

    EIP-3500 Front View Remote control sensor Usable Range 30° The remote control can be used to control 30° the projector within the ranges shown in the Remote control illustration. signal transmitters 30° 23' (7 m) Note Remote control The signal from the remote control can be reflected off a screen for easy operation.

  • Page 15: Connection Pin Assignments

    EIP-3500 Connection Pin Assignments INPUT 1/INPUT 2 and OUTPUT RGB Signal Terminal: 15-pin Mini D-sub female connector RGB Input Component Input 1. Video input (red) 1. P 2. Video input (green/sync on green) 2. Y 3. Video input (blue) 3. P 4.

  • Page 16: Dimensions

    EIP-3500 DIMENSIONS Units: inches (mm) Rear View Side View Top View Side View (310) (55.05) Front View (99.95) (129.5) (129.5) (29.1) (30.9) Bottom View (44.1) (30.9)

  • Page 17: Removing Of Major Parts

    EIP-3500 REMOVING OF MAJOR PARTS * Before removing the projection lens, set the IRIS setting to “High Contrast”. (See page 25.) 1. Removing the lamp door and the lamp unit 1-1. Loosen the lamp door fixing screw, slide the lamp door in allow direction and lift off the lamp door.
  • Page 18 EIP-3500 3. Attaching the top body (For the screws to apply, refer back to "2. Removing the top body".) 3-1. Insert the postcard over the lens barrel. 3-2. Place the top body in position. Make sure the four hooks are tightly caught.
  • Page 19 EIP-3500 5. Removing the optical mechanism unit 5-1. Remove the fixing screw for the optical mechanism unit from the bottom body. 5-2. Remove 5 fixing screws for the optical mechanism unit. 5-3. Remove the duct. Duct Optical Mechanism Unit 6. Removing the ballast/power supply unit 6-1.
  • Page 20 EIP-3500 7. Removing the ballast/power supply unit 7-1. Remove the fixing screw for the rear R/C PWB unit. 7-2. Remove 4 fixing screws, 4 WH bosses and the edge saddle for the ballast unit. 7-3. Remove 11 fixing screws and 5 WH bosses for the power supply unit.
  • Page 21 EIP-3500 9. Fixing the grounding plate 9-1. Install the four nuts. 9-2. Fit the reinforcement (bracket A) in position. 9-3. Place the grounding plate as specified. 9-4. Fit the reinforcement (bracket B) in position. 9-5. Tighten up the four M3 screws.

  • Page 22: Resetting The Total Lamp Timer

    5% or less, or when you notice a significant deterioration in the picture and color quality. The lamp life (percentage) can be checked with the on-screen display. Purchase a replacement lamp unit of type AH-35001 from your place of purchase, nearest EIKI Au- thorized Projector Dealer or Service Center.
  • Page 23 The internal Red on Take the projector to your nearest warning temperature is Cooling fan break- (Standby) EIKI Authorized Projector Dealer indicator abnormally high. down or Service Center for repair. Internal circuit failure Clean the exhaust and intake Clogged air intake vents.

  • Page 24: The Optical Unit Outline

    EIP-3500 THE OPTICAL UNIT OUTLINE Layout for proper setup of the optical components and parts (top view) (Schematic diagram) Reflection mirror Projection lens Color wheel Lamp Field lens UV Filter Illumination lenses 1 Illumination lenses 2 Item Function Lamp Light source. DC high-pressure mercury lamp.
  • Page 25 EIP-3500 Air blow direction Exhaust fans 1 and 2 After replacing the DMD, if shading is present on the screen as shown in Figure 1, adjust the lighting area of the DMD by turning the adjustment screws for the optical engine.

  • Page 26: Electrical Adjustment

    EIP-3500 ELECTRICAL ADJUSTMENT Adjusting point Adjusting conditions Adjusting procedure » Make the following settings. EEPROM 1. Turn on the power (with the initialization Press S3563 to call the process mode and execute lamp on) and warm up the "SS2" on SS menu.
  • Page 27 EIP-3500 Adjusting point Adjusting conditions Adjusting procedure DTV R Contrast 1. Send white/black window 1. Check the fixed value. adjustment pattern signals with 100% R-Bright: 63 (manual or (0.7 Vpp)/0% of amplitude 2. Observe the chroma of 100% white window pattern automatic) level of 480P to input 1.
  • Page 28 EIP-3500 Adjusting point Adjusting conditions Adjusting procedure Adjustment of 1. Select the following group 1. Check the fixed value. DVD color satura- and subject. Color : 12 tion Group : DVD Subject : Color Video Bright / 1. Select the following group 1.
  • Page 29 EIP-3500 Adjustment when assembling Adjusting point Adjusting conditions Adjusting procedure Adjustment of 1. Read voltage rank of DLP 1. Carry out adjustment when DLP chip has been re- DLP voltage description. placed or combination of chip and formatter has been 2.
  • Page 30 EIP-3500 Adjusting point Adjusting conditions Adjusting procedure Delivery set- 1. Make the following settings. tings Destination Process Remote control adjustment adjustment Factory setting at 4 Europe and the Other Factory setting at 3 Contries...
  • Page 31 EIP-3500 AF (autofocus) inspection < Camera > Required conditions: 1. Place the unit in front of the screen (size: 60-inch diagonal) at the distance of 1.8m. There is no light source such as a fluorescent light or reflector in the background.
  • Page 32 EIP-3500 » Adjustment mode process menu Adjustment mode process menu 1 * Adjust only the shaded items below. Adjustment Process Menu First layer VERSION VIDEO TEMP OPTION LAMP LINE VIDEO1 Pedestal EXIT second layer Initial Value second layer Initial Value...
  • Page 33 EIP-3500 Adjustment mode process menu 2 second layer Initial Value VERSION Build Boot Code Config RomCode AF Unit EXIT SS3 EU SS4 US SS5 JPN SS6 CHIN EXIT TEMP Temp1 Parameter of sensor1 Temp2 Parameter of sensor2 EXIT OPTION Pixel Gamma...

  • Page 34: Troubleshooting Table

    EIP-3500 TROUBLESHOOTING TABLE Checking the basic operation Does the power LED light up or flash in Go to "Checking the power supply system". red or green? Go to "Checking the peripheral circuits of Does the set function with its keys or the remote controller? the microprocessor".
  • Page 35 EIP-3500 Checking the power supply system Is 13V output to pins (9) and (11) of Go to "Checking the power unit". P1707? Is 6V output to pins (1) and (3) of P1707? Go to "Checking the power unit". Is the connector of P1708 fully inserted? Replace the thermal fuse.
  • Page 36 EIP-3500 Checking the power unit Is each connector of the power unit Securely insert the connectors. fully inserted? Is the lamp door closed completely? Fix the lamp door with screws. Replace the bimetal switch or restore Is the bimetal broken? by pressing the red button.
  • Page 37 EIP-3500 Checking the peripheral circuits of the microprocessor Are the voltages of approx. 3.3V and 2.5V Go to "Checking the power supply applied to both ends of C2030 and C2029 system". respectively? Are the oscillations of 133MHz and Check the peripheral circuits of X2001 64MHz output from pin (3) of X2001 and and X2002.
  • Page 38 EIP-3500 Checking the lamp light-up Does each cooling fan Check the power supply circuit function? or fan circuit on the main circuit. ABNORMAL Check IC9102, 9003 and Go to "Checking the Is the rotating sound of the the peripheral circuits of...
  • Page 39 EIP-3500 Checking the peripheral circuits What is the screen problem? of the formatter The rainbow-like screen is Thick and white displayed. Each color (R, The screen is all black. Other vertical lines (flash). G and B) does not match. The problem remains...
  • Page 40 EIP-3500 Checking the RGB input Send RGB signals to INPUT1 or INPUT2. Use keys on the main unit or remote control to select INPUT1 or INPUT2. Are sync signals input to pins Go to "Checking the sync (30) and (31) of IC3005? signal".
  • Page 41 EIP-3500 Checking the Component Send component signals to INPUT1 or INPUT2. Use keys on the main unit or remote control to select INPUT1 or INPUT2. Is picture signal including sync signal input to pin (46) of IC3002? Are picture signals input to...
  • Page 42 EIP-3500 Checking of Video input Send composite VIDEO signals to INPUT3. Use keys on the main unit or remote control to select INPUT3. Is picture signal input to pin Check the VIDEO-IN signal line (1) of IC3103? of Q3104 and soldering of J3101.
  • Page 43 EIP-3500 Checking of Sync signal Are HV sync signals sent to Check IC4008 and peripheral circuits. pins (1) and (6) of IC4010? IC4008 and IC4010 are Are HV sync signals sent to defective. pins (22) and (23) of IC3002? Is a clock of 27MHz sent to pin...
  • Page 44 EIP-3500 Checking the autofocus Remove the dust and dirt, or Is dust, dirt or damage present replace. on the auto focus sensor cover? Check the power supply circuit Are voltages of 3.3V, 1.5V and and its peripheral circuits. 2.8V applied to pin (4) of X5001,...
  • Page 45 IC8003 (EEP ROM)" to reset. Are the network device (e.g. Hub) Repair defective parts in the network. between the control PC and EIP-3500 and cable normal? When data is sent from the control PC, do Check the peripheral circuit of J8201 (RJ-45 jack pins (30) and (31) of IC8201 (PHY with built-in transformer).
  • Page 46 EIP-3500 Checking RS-232C Communication is disabled even though connecting the control PC and projector with a RS-232C cable. Is the connecting cable connected Replace the connecting cable. correctly? (cross cable) Does pin (8) of IC8002 receive a signal? Check R8002 and the peripheral circuits of SC8001.
  • Page 47 EIP-3500 Resetting after replacing IC8003 (EEP ROM) MAC address returns to default. Follow the steps below to reset. 1 Open the top cabinet of the projector and confirm the MAC address (MAC: ************) of the seal on the PWB. 2 Connect the control PC and projector with a RS-232C cable.

  • Page 48: Chassis Layout

    EIP-3500 CHASSIS LAYOUT FORMATTER UNIT DUNTKC613WEF0 POWER UNIT RDENCA118WJZZ...
  • Page 49 EIP-3500 FRONT R/C RECEIVER UNIT DUNTKC615WEF3 MAIN UNIT DUNTKC612WEF3 BALLAST UNIT RDENCA088WJZZ REAR R/C RECEIVER UNIT DUNTKC681WEF3...

  • Page 50: Block Diagram

    EIP-3500 BLOCK DIAGRAM...
  • Page 51 EIP-3500...

  • Page 52: Overall Wiring Diagram

    EIP-3500 OVERALL WIRING DIAGRAM...
  • Page 53 EIP-3500...

  • Page 54: Waveforms

    EIP-3500 WAVEFORMS 1 IC3101 (28) pin 2 IC3101 (29) pin 3 IC3101 (31) pin 4 IC3101 (35) pin (VS-OUT) (HS-OUT) (SCP-IN) (R-OUT) H : 4m sec/div H : 20µ sec/div H : 20µ sec/div H : 10µ sec/div V : 1V/div...

  • Page 55: Printed Wiring Board Assemblies

    EIP-3500 PRINTED WIRING BOARD ASSEMBLIES FRONT R/C Unit (Side A) FRONT R/C Unit (Side B) REAR R/C Unit (Side A) REAR R/C Unit (Side B)
  • Page 56 EIP-3500 MAIN Unit (Side-A)
  • Page 57 EIP-3500...
  • Page 58 EIP-3500 MAIN Unit (Side-B)
  • Page 59 EIP-3500...
  • Page 60 EIP-3500 FORMATTER Unit (Side-A)
  • Page 61 EIP-3500 FORMATTER Unit (Side-B)
  • Page 62 EIP-3500 POWER BALLAS Unit (Side A) POWER BALLAST Unit (Side B)

  • Page 63: Parts List

    E IP -3500 PA R T S L IS T R ef. No. Part No. Des c ription C ode R ef. No. Part No. Des c ription C ode R ef. No. Part No. Des c ription C ode DUNT K C 612WE F 3 PA R T S R E P L AC E ME NT MA IN UNIT...
  • Page 64 EIP-3500 Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTKC612WEF3 D1705 VHDHSU119//-1Y HSU119 D1706 VHDHSU119//-1Y HSU119 MAIN UNIT (Continued) D1707 VHDHSU119//-1Y HSU119 D1708 VHDHSU119//-1Y HSU119 D1709 VHDHSU119//-1Y HSU119 IC5003 RH-iXB126WJZZQ EP1C6T144C8N D1710 VHDHSU119//-1Y HSU119 IC5004 RH-iXB127WJZZY...
  • Page 65 EIP-3500 Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTKC612WEF3 C1725 VCEAPF1EW336MY Electrolytic C1726 VCEAPF1CW106MY Electrolytic MAIN UNIT (Continued) C1731 RC-KZA070WJZZY 6.3V Ceramic C1732 VCKYTV1CB105KY Ceramic C1733 VCKYCY1HB103KY 0.01 Ceramic D8001 RH-EX1271CEZZY Zener Diode, 12V C1735 VCKYCY1HB332KY...
  • Page 66 EIP-3500 Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTKC612WEF3 C3101 VCKYCY1AB105KY Ceramic C3102 VCKYCY1AB105KY Ceramic MAIN UNIT (Continued) C3103 VCKYCY1EF104ZY Ceramic C3104 VCKYCY1AB105KY Ceramic C3105 VCKYCY1AB105KY Ceramic C2030 VCAAPD0JJ476MY 6.3V Electrolytic C3106 VCKYCY1AB105KY Ceramic C2031 VCKYCY1EF104ZY...
  • Page 67 EIP-3500 Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTKC612WEF3 C4014 VCEAPF1CW106MY Electrolytic C4015 VCEAPF1CW106MY Electrolytic MAIN UNIT (Continued) C4016 VCEAPF1CW106MY Electrolytic C4017 VCEAPF1CW106MY Electrolytic C4018 VCEAPF1HW105MY Electrolytic C3185 VCKYCY1EF104ZY Ceramic C4019 VCEAPF1HW105MY Electrolytic C3187 VCKYCY1HB103KY 0.01...
  • Page 68 EIP-3500 Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTKC612WEF3 R1745 VRS-CY1JF133FY 13k 1/16W Metal Oxide R1746 VRS-CY1JF000JY 1/16W Metal Oxide MAIN UNIT (Continued) R1747 VRS-CY1JF103JY 10k 1/16W Metal Oxide R1748 VRS-CY1JF101JY 100 1/16W Metal Oxide...
  • Page 69 EIP-3500 Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTKC612WEF3 R2707 VRS-CY1JF102JY 1/16W Metal Oxide R2708 VRS-CY1JF103JY 10k 1/16W Metal Oxide MAIN UNIT (Continued) R2709 VRS-CY1JF104JY 100k 1/16W Metal Oxide R2711 VRS-CY1JF124JY 120k 1/16W Metal Oxide...
  • Page 70 EIP-3500 Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTKC612WEF3 R3526 VRN-CY1JF472DY 4.7k 1/16W Metal Film R3527 VRS-CY1JF184FY 180k 1/16W Metal Oxide MAIN UNIT (Continued) R3528 VRS-CY1JF103JY 10k 1/16W Metal Oxide R3529 VRS-CY1JF392JY 3.9k 1/16W Metal Oxide...
  • Page 71 EIP-3500 Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTKC612WEF3 R4091 VRS-CY1JF103JY 10k 1/16W Metal Oxide R4092 VRS-CY1JF103JY 10k 1/16W Metal Oxide MAIN UNIT (Continued) R4093 VRS-CY1JF562JY 5.6k 1/16W Metal Oxide R4094 VRS-CY1JF472JY 4.7k 1/16W Metal Oxide...
  • Page 72 EIP-3500 Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTKC612WEF3 FB1702 RBLN-0207TAZZY Ferrite Bead FB1703 RBLN-0061TAZZY Ferrite Bead MAIN UNIT (Continued) FB1704 RBLN-0061TAZZY Ferrite Bead FB1705 RBLN-0061TAZZY Ferrite Bead R8043 VRS-CY1JF103JY 10k 1/16W Metal Oxide FB1706 RBLN-0252TAZZY...

  • Page 73: Formatter Unit

    EIP-3500 Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTKC612WEF3 DUNTKC613WEF0 MAIN UNIT (Continued) FORMATTER UNIT INTEGRATED CIRCUITS FB8203 RBLN-0210TAZZY Ferrite Bead FB8204 RBLN-0210TAZZY Ferrite Bead IC9001 VHiTCDCR83D-1Y CDCR83DBQR FB8205 RBLN-0061TAZZY Ferrite Bead IC9003 RH-iXA089WJN2Q J2201...
  • Page 74 EIP-3500 Ref. No. Part No. Description Code Ref. No. Part No. Description Code C9547 VCKYCY1EF104ZY Ceramic DUNTKC613WEF0 C9548 VCKYCY1EF104ZY Ceramic FORMATTER (Continued) C9549 VCKYCY1EF104ZY Ceramic C9550 VCKYCY1EF104ZY Ceramic C9551 VCKYCY1EF104ZY Ceramic C9061 VCKYCY1CB104KY Ceramic C9552 VCKYCY1EF104ZY Ceramic C9062 VCKYCY1CB104KY Ceramic...
  • Page 75 EIP-3500 Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTKC613WEF0 DUNTKC615WEF3 FORMATTER (Continued) FRONT R/C UNIT R9532 VRS-CY1JF102JY 1/16W Metal Oxide CAPACITORS R9542 VRS-CY1JF111FY 110 1/16W Metal Oxide C1501 VCKYCY1EF104ZY Ceramic R9554 VRS-CY1JF102JY 1/16W Metal Oxide...
  • Page 76 EIP-3500 Ref. No. Part No. Description Code Ref. No. Part No. Description Code R703 9FJ0R92001385 470k 1/8W Resistor RDENCA118WJZZ R704 9FJ0R92001385 470k 1/8W Resistor POWER/ SUPPLY UNIT R705 9FJ0R92001385 470k 1/8W Resistor R709 9FJ0R22001570 Resistor R710 9FJ0R92203975 100k 1/8W Resistor...
  • Page 77 EIP-3500 Ref. No. Part No. Description Code Ref. No. Part No. Description Code RDENCA118WJZZ POWER/ SUPPLY UNIT(Continued) MISCELLANEOUS PARTS B701 9FJ0L08001805 B01AT1F B702 9FJ0L08002275 BL01RN1A1F1A 9FJ0O01110015 Earth Terminal, Y1811 å F701 9FJ0E02101080 Fuse, T6.3AH AV250V å THP701 9FJ0E03001130 Thermal Fuse, HU4X å...

  • Page 78: Cabinet And Mechanical Parts

    EIP-3500 Ref. No. Part No. Description Code Ref. No. Part No. Description Code PSLDMA442WJFW Ballast Shield CABINET AND MECHANICAL PARTS PZETKA098WJKZ Ballast Insulator PZETKA110WJKZ R/C Insulator QCNW-C667WJPZ Connecting Wire å QCNW-C671WJPZ Power SW Wire (PA) Not Available Top Body Ass'y Unit...
  • Page 79 EIP-3500 CABINET AND MECHANICAL PARTS 23-1 23-3 23-2 23-1 2-10 å 2-17 2-1-10 2-10 2-17 2-1-4 2-1-2 57 37 2-1-1 2-1-9 2-1-3 2-16 See page 21. 2-1-5 2-17 2-1-6 2-11 2-14 2-14 2-11 2-1-11 2-2-5 3-1-2 2-1-11 2-1-7 2-1-8 2-2-4...
  • Page 80 EIP-3500 Ref. No. Part No. Description Code Ref. No. Part No. Description Code 4-67 XSSSN20P07000 Screw, x2 4-68 XWHUW40-03000 C/W Washer OPTICAL MECHANISM PARTS 4-69 XBPSN20P10JS0 Screw 4-70 LHLDWA097WJZZ Wire Holder CCHSKA016WJ21 Optical mechanism Ass'y AH-35001 Lamp Unit, Option LCHSKA016WJFW...
  • Page 81 EIP-3500 Ref. No. Part No. Description Code Ref. No. Part No. Description Code OPTICS MECHANISM PARTS 4-25 4-12 4-41 4-48 4-12 4-61 4-41 4-18 4-29 4-27 4-69 4-70 4-58 4-17 4-46 4-58 4-66 4-23 4-66 4-24 4-66 4-50 4-22 4-35...

  • Page 82: Ë Accessories Parts

    EIP-3500 Ref. No. Part No. Description Code Ref. No. Part No. Description Code PACKING PARTS SUPPLIED ACCESSORIES (NOT REPLACEMENT ITEM) GCASNA018WJSA Soft Case SPAKCB789WJZZ Packing Case QACCDA010WJPZ Power Cord for U.S., SPAKFA577WJZZ Access Case å Canada, etc. SPAKPA360WJZZ Polystylene Cover å...

  • Page 83: Packing Of The Set

    EIP-3500 Ref. No. Part No. Description Code Ref. No. Part No. Description Code PACKING OF THE SET Operation Manual Polystylene Bag (TiNS-B671WJZZ) (English) (SSAKAA018WJZZ) (TiNS-B672WJZZ) (French) (TiNS-B673WJZZ) (Spanish) QUICK GUID Polystylene Bag Power Cord (TiNS-B723WJZZ) (SSAKAA018WJZZ) for U.S., Canada, etc.
  • Page 84 EIP-3500...

Table of Contents