Page 2
Projector, please record the Serial Number located on the bottom of the projector and retain this information. Before recycling the packaging, please ensure that you have checked the contents of the carton thoroughly against the list of “Supplied accessories” on page 10. Model No.: EIP-3500 Serial No.:...
Page 3
SPECIAL NOTE FOR USERS IN THE U.K. The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 10A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked above, which is also indicated on the pin face of the plug, must be used.
Page 4
The supplied CD-ROM contains SETUP GUIDE in English, German, French, Spanish, Italian, Portuguese and Japanese. Die mitgelieferte CD-ROM enthält Einrichtungs-Anleitung in Englisch, Deutsch, Französisch, Spanisch, Italienisch, Portugiesisch und Japanisch. Le CD-ROM fourni contient le guide d’installation en anglais, allemand, français, espagnol, italien, portugais et japonais.
Page 5
2. CONSUMER PRODUCT SAFETY ACT To ensure that you will promptly receive any safety notification of inspection, modification, or recall that EIKI may be required to give under the 1972 Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT “LIMITED WARRANTY” CLAUSE.
United States of America, the Electronic Industries Alliance: www.eiae.org . This EIKI projector uses a DMD panel. This very sophisticated panel contains 786,432 pixels micromirrors. As with any high technology electronic equipment such as large screen TVs, video systems and video cameras, there are certain acceptable tolerances that the equipment must conform to.
How to Read this Operation Manual • • • • • In this operation manual, the illustrations and on-screen displays are simplified for explana- tion. This may differ from the actual on-screen display. Using the Menu Screen The menu can be operated to achieve two functions, adjustments and settings. (For setting the menu items, see pages 42 and 43.
Contents Preparing Introduction How to Read this Operation Manual ... 3 Contents ... 4 IMPORTANT SAFEGUARDS ... 6 How to Access the PDF SETUP GUIDE ... 9 Accessories ... 10 Part Names and Functions ... 11 Using the Remote Control ... 15 Usable Range ...
Page 9
Reference Appendix Maintenance ... 63 Maintenance Indicators ... 64 Regarding the Lamp ... 66 Lamp ... 66 Caution Concerning the Lamp ... 66 Replacing the Lamp ... 66 Removing and Installing the Lamp Unit ... 67 Resetting the Lamp Timer ... 68 Computer Compatibility Chart ...
IMPORTANT SAFEGUARDS CAUTION : Please read all of these instructions before you operate this product and save these instructions for later use. Electrical energy can perform many useful functions. This product has been engineered and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS.
Page 11
Internal cleaning should only be performed by a EIKI Authorized Projector Dealer or Ser- vice Center. Do not set up the projector in places ex- posed to direct sunlight or bright light.
Page 12
IMPORTANT SAFEGUARDS Caution regarding usage of the projector ■ When using the projector, ensure not to sub- ject it to hard impact and/or vibration, as this can result in damage. Take extra care with the lens. If you are not to use the projector for a long time, ensure to unplug the power cord from the wall outlet, and disconnect any other cables connected to it.
How to Access the PDF SETUP GUIDE PDF “SETUP GUIDE” in several languages are included in the CD-ROM, so that you can work with the projector. To utilize this SETUP GUIDE, you need to install Adobe computer (Windows ® or Macintosh Please download Adobe ®...
Accessories Supplied accessories Some accessories (Remote control and Power cord etc.) are placed in the pocket of the storage case when shipped from the factory. Remote control RRMCGA371WJSA Power cord For U.S., Canada, etc. (12' (3.6 m)) QACCDA010WJPZ Use the power cord that corresponds to the wall outlet in your country. 3 RCA to 15-pin D-sub cable (9'10'' (3.0 m)) QCNWGA043WJPZ...
Part Names and Functions Numbers in refer to the main pages in this operation manual where the topic is explained. Projector Top View POWER button For turning the power on or putting the projector into standby mode. KEYSTONE button For entering the Keystone Correction mode.
Part Names and Functions About the Indicators on the Projector Power indicator Green on ... Normal (Standby) Red on ... Normal (Power on) Lamp indicator Green on ... Normal Green blinks ... The lamp is warming up or shutting down. Red on ...
Page 17
Numbers in refer to the main pages in this operation manual where the topic is explained. Projector (Rear View) Terminals Refer to “INPUT/OUTPUT Terminals and Connectable Main Equipment” on page 21. AUDIO OUTPUT terminal Audio output terminal of equipment connected to the AUDIO INPUT terminal.
Part Names and Functions Numbers in refer to the main pages in this operation manual where the topic is explained. Remote Control POWER button For turning the power on or putting the projector into standby mode. ZOOM buttons For adjusting the projected image size.
Using the Remote Control Usable Range The remote control can be used to control the projector within the ranges shown in the illustration. Note • The signal from the remote control can be reflected off a screen for easy operation. However, the effective distance of the sig- nal may differ depending on the screen material.
Quick Start This section shows the basic operation (projector connecting with the computer). For details, see the page described below for each step. Setup and Projection In this section, connection of the projector and the computer is explained using one example. Place the projector facing a screen Connect the projector to the computer and plug the power cord into the AC socket of the projector...
Page 21
Adjust the angle Adjust the projector angle • • • • • Adjust the projector angle using the HEIGHT ADJUST button. HEIGHT ADJUST button Adjust the focus and the zoom 1 1 1 1 1 Bring the projected image into focus •...
Storing the Projector How to Use the Storage Case When storing the projector, attach the lens cap to the lens, and place it in the supplied storage case. Open the cover of the storage case. Place the projector into the stor- age case.
Setting up the Projector Setting up the Projector Position the projector perpendicular to the screen with the projector’s feet flat and level to achieve an optimal image. Note • The projector lens should be centered in the middle of the screen. If the horizontal line passing through the lens center is not perpendicular to the screen, the image will be distorted, making viewing difficult.
• When using a mirror, ensure that both the projector and the mirror are carefully placed so the projected light does not shine into the eyes of the audience. Ceiling-mount Setup ■ It is recommended that you use the optional EIKI ceiling-mount bracket for this installation. Before mounting the projector, contact your nearest EIKI Autho- rized Projector Dealer or Service Center to obtain the recom- mended ceiling-mount bracket (sold separately).
Connections INPUT/OUTPUT Terminals and Connectable Main Equipment INPUT 1, 2 terminal Connecting the computer. (See page 23.) Connecting video equipment with component output terminal (DVD player, DTV decoder, DVD recorder with hard disc, etc.). (See page 25.) INPUT 4 terminal Connecting video equipment with S-video output terminal (VCR, DVD player, etc.).
Samples of Cables for Connection • For more details of connection and cables, refer to the operation manual of the connecting equipment. • You may need other cables or connectors not listed below. Terminal on Equipment connected equipment Computer output terminal Audio output terminal Audio-visual...
Connecting to a Computer Before connecting, ensure the power cord of the projector from the AC outlet is unplugged, and that the devices to be connected are turned off. After making all connections, turn on the projector and then the other devices. When connecting a computer, ensure that it is the last device to be turned on after all the connections are made.
Connecting to a Computer Using the Remote Control as the Wireless Computer Mouse When connecting the projector and the computer with the supplied RGB cable and USB cable (see page 23), you can use the remote control as the computer mouse. The mouse pointer can be operated in the following way after it is connected.
Connecting to Video Equipment The projector has a COMPUTER-RGB/COMPONENT terminal, an S-VIDEO terminal and VIDEO terminal for video input. Refer to the listed illustrations on how to connect audio-visual equipment. The image quality is highest in order of the component signal, the RGB signal, the S-video signal and the video signal.
Page 30
Connecting to Video Equipment When connecting video equipment with video output terminal To audio output terminal To video output terminal ø3.5 mm minijack to RCA audio cable (commercially available) When connecting video equipment with S-video output terminal To audio output terminal To S-video output terminal ø3.5 mm minijack to RCA audio cable (commercially...
Controlling the Projector by a Computer When the RS-232C terminal on the projector is connected to a computer with a DIN-D-sub RS-232C adaptor and an RS-232C serial control cable (cross type, commercially available), the computer can be used to control the projector and check the status of the projector.
Connecting to a Monitor with RGB Input Terminal You can display computer images on both the projector and a separate monitor using two sets of RGB cables. Monitor To RGB input terminal RGB cable (commercially available) Note • RGB signals and Component signals can be output to the monitor. •...
Turning the Projector On/Off Connecting the Power Cord Plug the supplied power cord into the AC socket on the rear of the projector. Turning the Projector on Before performing the steps in this section, connect any equipment that you use with the projector.
Image Projection Using the Adjustment Feet The height of the projector can be adjusted using the adjustment feet at the front and rear of the projector when the screen is located higher than the projector, the screen is inclined or when the installation site is slightly inclined. Install the projector so that it is as perpen- dicular to the screen as possible.
Correcting Trapezoidal Distortion Auto Keystone Correction When the image is projected either from the top or from the bottom towards the screen at an angle, the image becomes distorted trapezoidally. The function for correcting trapezoidal distortion is called Keystone Correction. This projector is equipped with an “Auto Keystone Correction”...
Image Projection Adjusting the Focus This projector is equipped with an “Auto Focus” function that adjusts the focus automatically when it is turned on. When you want to readjust the focus after the Auto Focus function has been activated, you can operate the Auto Focus func- tion using the following procedure.
Switching the INPUT Mode Select the appropriate input mode for the con- nected equipment. Press mote control to select the input mode. • • • • • When pressing ' ' ' or " " " " " on the projector, input mode switches in order of : INPUT 1 INPUT 2...
Image Projection Displaying the Black Screen and Turning off the Sound Temporarily Press on the remote control to temporarily display a black screen and turn off the sound. Note • Pressing again will turn the projected image and sound back on. Displaying an Enlarged Portion of an Image Graphs, tables and other portions of projected...
Freezing a Moving Image Press on the remote control. • The projected image is frozen. Press again to return to the moving image from the currently connected equipment. Selecting the Picture Mode You can select the suitable picture mode for the projected image, such as movie or video game.
Image Projection This function allows you to modify or customize the resize mode to enhance the input image. Depend- ing on the input signal, you can choose “NORMAL”, “DOT BY DOT”, “BORDER” or “STRETCH” image. Resize Mode Press on the remote control. •...
Page 41
VIDEO • “STRETCH” is fixed when 540P, 720P or 1080 Input Signal DVD / Video Image type 4:3 aspect ratio Letter box 480I, 480P, NTSC, PAL, SECAM Squeezed 16:9 image Squeezed 4:3 image 16:9 aspect ratio 540P, 720P, 1080I (16:9) 16:9 aspect ratio (4:3 aspect ratio in 16:9 screen)
Menu Items The following shows the items that can be set in the projector. “Picture” menu INPUT 1 (RGB) / INPUT 2 (RGB) INPUT 1 (Component) / INPUT 2 (Component) INPUT 3 / INPUT 4 “Fine Sync” menu INPUT 1 / INPUT 2 Note When using the INPUT 1 or INPUT 2 mode: •...
Page 43
“Options1” menu Example: INPUT 3 / INPUT 4 “Options2” menu “Language” menu Main Menu Lamp Timer(Life) Options1 Page Page Resize Normal Border Page Dot By Dot Stretch OSD Display [ON/OFF] Page Video System Auto Page NTSC3.58 SECAM NTSC4.43 PAL-M PAL-N PAL-60 Background Logo...
Using the Menu Screen The menu can be operated to achieve two functions, adjustments and settings. (For setting the menu items, see pages 42 and 43. ) Menu Selections (Adjustments) Example: Adjusting “Bright” • This operation can also be performed by using the buttons on the projector. Press •...
Page 45
' ' or " " " to select the item " " Press ' you want to adjust. • The selected item is highlighted. To adjust the pro- jected image while viewing it Press • The selected single adjustment item (e.g.
Using the Menu Screen The menu can be operated to achieve two functions, adjustments and settings. (For adjust- ing the menu items, see pages 40 and 41.) Menu Selections (Settings) Example: Setting “Menu Position” • This operation can also be performed by using the buttons on the projector. Press •...
Page 47
' ' or " " " to select the " " Press ' item you want to set, and then press | | | | | to display the sub menu. • The selected item is highlighted. • When you select “System Lock” on the “Options1”...
Picture Adjustment (“Picture” menu) You can adjust the projector’s picture to your preferences using the “Picture” menu. Selecting the Picture Mode This function allows you to select the picture mode in accordance with brightness of the room or content of the image to be projected. In all picture modes, items on the “Picture”...
Emphasizing the Contrast This function emphasizes the bright portions of images to obtain a higher contrast image. Menu operation Page 40 Example: “Picture” screen menu for IN- PUT 1 (RGB) mode Description of Bright Boost Setting Description To improve color To increase brightness, reproduction, lower increase bright boost...
Picture Adjustment (“Picture” menu) sRGB Setting When you want to display the image in a natural tint based on an original image from the com- puter, select “sRGB” and set it to “ Menu operation Page 42 Example: “Picture” screen menu for IN- PUT 1 (RGB) mode Note •...
Signal Type Setting This function allows you to select the input sig- nal type RGB or Component for INPUT 1 or IN- PUT 2. Menu operation Page 42 Example: “Picture” screen menu for IN- PUT 1 (RGB) mode Description of Signal Type Settings Selectable items Description Auto...
Computer Image Adjustment (“Fine Sync” menu) You can adjust the computer image, match the computer display mode, and confirm the input signal using the “Fine Sync” menu. Adjusting the Computer Image Use the Fine Sync function in case of irregulari- ties such as vertical stripes or flickering in por- tions of the screen.
Auto Sync Adjustment Used to automatically adjust a computer image. Menu operation Page 42 Example: “Fine Sync” screen menu for INPUT 1 (RGB) mode Description of Auto Sync Adjustment Selectable items Description Auto Sync adjustment will occur when the projector is turned on or when the (ON) input signals are switched, when connected to a computer.
Using the “Options1” Menu You can use the “Options1” menu to enhance the usage for the projector. Checking the Lamp Life Status You can confirm the cumulative lamp usage time and the remaining lamp life (percentage). Menu operation Page 42 Example: “Options1”...
Setting On-screen Display This function allows you to turn the on-screen messages on or off. Menu operation Page 42 Example: “Options1” screen menu for INPUT 1 (RGB) mode Description of OSD Display Settings Selectable items Description (ON) All On-screen Displays are displayed. INPUT/VOLUME/AV MUTE/FREEZE/ AUTO SYNC/ENLARGE/ “An invalid (OFF)
Using the “Options1” Menu Selecting a Startup and Background Image Menu operation Page 42 Example: “Options1” screen menu for INPUT 1 (RGB) mode Description of Background Images Selectable items Description Logo Default image Blue Blue screen None Black screen* Note * If the input signal has interference, the screen will be displayed during interference.
Auto Power Off Function Menu operation Page 42 Example: “Options1” screen menu for INPUT 1 (RGB) mode Description of Auto Power Off Selectable items Description The projector automatically enters the (ON) standby mode when no input signal is detected for 15 minutes or longer. The Auto Power Off function will be (OFF) disabled.
Info • If you lose or forget your keycode, contact your nearest EIKI Authorized Projector Dealer or Ser- vice Center. Even if the product warranty is valid, the keycode reset will incur a charge.
Changing the keycode Press the buttons on the remote control or on the projector to enter the preset keycode in “Old Code”. Press the 4 buttons on the remote control or on the projector to enter the new keycode in “New Code”. Enter the same keycode in “Recon- firm”.
Helpful Functions Set during Installation (“Options2” menu) Setting a Password There is no factory preset for the password, so • • • • • the “Options2” menu is enabled. If you do not want others to operate the “Op- • • • • • tions2”...
Auto Focus Setting When the projector is turned on, the focus pat- tern is displayed automatically and the focus is adjusted automatically. Menu operation Page 42 Example: “Options2” screen menu Description of Auto Focus Selectable items Description Focus is adjusted automatically when the (ON) power is turned on.
Helpful Functions Set during Installation (“Options2” menu) Speaker Setting This function allows you to set the audio output of the internal speaker to “ such as when the projector is connected to an external amplifier. Menu operation Page 42 Example: “Options2” screen menu Description of Speaker Settings Selectable items Description...
Reversing/Inverting Pro- jected Images This projector is equipped with a reverse/invert image function that allows you to reverse or in- vert the projected image for various applications. Menu operation Page 42 Example: “Options2” screen menu Description of PRJ Modes Selectable items Description Front Normal image...
Helpful Functions Set during Installation (“Options2” menu) Monitor Output Settings When the Monitor Out has been set to “Enable”, the monitor output is activated and power is con- sumed even in the standby mode. It is recom- mended that the Monitor Out be set to “Disable” when it is not connected.
Example: “Options2” screen menu Description of Network Information Displayed items Description The projector name is displayed. Projector (Factory preset : EIP-3500) The IP address set for the projector is IP Address displayed. (Factory preset :192.168.150.2) The MAC address of the projector is MAC Address displayed.
Using the “Language” Menu Selecting the On-screen Display Language The projector can switch the on-screen display language among 11 languages: English, German, Spanish, Dutch, French, Italian, Swedish, Portu- guese, Chinese, Korean or Japanese. Example: “Language” screen menu for INPUT 1 (RGB) mode Press on the remote control.
Maintenance Cleaning the projector ■ Ensure the power cord is unplugged before cleaning the projector. ■ The cabinet as well as the operation panel is made of plastic. Avoid using benzene or thinner, as these can damage the finish on the cabinet. ■...
Maintenance Indicators ■ The warning lights on the projector indicate problems inside the projector. ■ If a problem occurs, either the temperature indicator or the lamp indicator will illuminate red, and the projector will enter the standby mode. After the projector has entered the standby mode, follow the procedures given below.
Page 69
Possible solution • Relocate the projector to an area with proper ventilation (see page • Take the projector to your nearest EIKI Authorized Projector Dealer or Service Center for repair. • Clean the exhaust and intake vents. (See page 63.) •...
Carefully change the lamp by following the instructions described in this section. *If you wish, you may have the lamp replaced at your nearest EIKI Authorized Dealer or Service Center. * If the new lamp does not illuminate after replacement, take your projector to the nearest EIKI Authorized Dealer or Service Center for repair.
Removing and Installing the Lamp Unit Info • Ensure the lamp unit is removed using the handle. Ensure the glass surface of the lamp unit or the inside of the projector are not touched. • To avoid injury to yourself and damage to the lamp, ensure to carefully follow the steps below.
Regarding the Lamp Remove the lamp unit. • Loosen the securing screws from the lamp unit. Hold the lamp unit by the handle and pull it in the direction of the arrow. At this time, keep the lamp unit horizontal and do not tilt it. Insert the new lamp unit.
Computer Compatibility Chart The table below lists signal codes that are compatible with the projector. When the images are distorted or cannot be projected, adjust the output signal of your computer and so forth while referring to the table below. Computer •...
Troubleshooting Problem No picture and no sound or projector does not start. Sound is heard but no picture appears. Color is faded or poor. Picture is blurred; noise appears. Picture appears but no sound is heard. An unusual sound is occasionally heard from the cabinet.
Page 75
Problem Picture is green on • Change the input signal type setting. INPUT 1 (COMPONENT)/ INPUT 2 (COMPONENT). Picture is pink (no green) on INPUT 1 (RGB)/ INPUT 2 (RGB). Picture is too bright and • Image adjustments are incorrectly set. whitish.
Weight (approx.) Replacement parts As a part of policy of continuous improvement, EIKI reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units.
Glossary Aspect Ratio Width and height ratio of an image. The normal aspect ratio of a computer and video image is 4:3. There are also wide images with an aspect ratio of 16:9 and 21:9. Auto Sync Optimizes projected computer images by auto- matically adjusting certain characteristics.