Page 2
IMPORTANT • For your assistance in reporting the loss or theft of your Projector, please record the Model and Serial Number located on the bottom of the projector and retain this information. • Before recycling the packaging, please ensure that you have checked the con- tents of the carton thoroughly against the list of “Supplied accessories”...
Page 4
The supplied CD-ROM contains operation instructions in English, German, French, Spanish, Italian and Portuguese. Carefully read through the operation instructions before operating the projector. Die mitgelieferte CD-ROM enthält Bedienungsanleitungen in Englisch, Deutsch, Französisch, Spanisch, Italienisch und Portugiesisch. Bitte lesen Sie die Bedienungsanleitung vor der Verwendung des Projektors sorgfältig durch.
Page 5
2. CONSUMER PRODUCT SAFETY ACT To ensure that you will promptly receive any safety notification of inspection, modification, or recall that EIKI may be required to give under the 1972 Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT “LIMITED WARRANTY”...
Caution Concerning Lamp Replacement See “Replacing the Lamp” on page 55. This EIKI projector uses a DMD panel. This very sophisticated panel contains 786,432 pixels (micromirrors). As with any high technology electronic equipment such as large screen TVs, video systems and video cameras, there are certain acceptable tolerances that the equipment must conform to.
How to Read this Owner’s Manual • In this owner’s manual, the illustration and the screen display are simplified for explanation, and may differ slightly from the actual display. Using the Menu Screen ENTER button Adjustment buttons (P/R/O/Q) MENU/HELP button Menu Selections (Adjustments) Example: Adjusting “Bright”.
Contents Preparing Introduction How to Read this Owner’s Manual ... 3 Contents ... 4 IMPORTANT SAFEGUARDS ... 6 How to Access the PDF Owner’s Manuals ... 10 Accessories ... 11 Part Names and Functions ... 12 Inserting the Batteries ... 15 Usable Range ...
Page 9
Reference Appendix Maintenance ... 52 Maintenance Indicators ... 53 Regarding the Lamp ... 55 Lamp ... 55 Caution Concerning the Lamp ... 55 Replacing the Lamp ... 55 Removing and Installing the Lamp Unit ... 56 Resetting the Lamp Timer ... 57 Computer Compatibility Chart ...
IMPORTANT SAFEGUARDS CAUTION: Please read all of these instructions before you operate this product and save these instructions for later use. Electrical energy can perform many useful functions. This product has been engineered and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS.
Page 11
15. Overloading Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock. 16. Object and Liquid Entry Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock.
Page 12
Internal cleaning should only be performed by an EIKI Authorized Dealer or Service Cen- ter. Do not set up the projector in places ex- posed to direct sunlight or bright light.
Page 13
I When turning off the projector, the cooling fan runs to decrease the internal temperature for a while. Unplug the power cord after the cool- ing fan stops. The period the cooling fan runs will vary, depending on the circumstances and the internal temperature.
How to Access the PDF Owner’s Manuals PDF owner’s manuals in several languages are included in the CD-ROM. To utilize these manuals, you need to install Adobe ® or Macintosh Please download Adobe Accessing the PDF Manuals For Windows ® 1 Insert the CD-ROM in the CD-ROM drive.
Accessories Supplied accessories Two R-6 batteries Remote control (“AA” size, UM/SUM-3, HP-7 or similar) DIN-D-sub RS-232C adaptor " (15 cm)) QCNWGA015WJPZ Power cord* For U.S. and Canada, etc. (6' (1.8 m)) QACCDA007WJPZ * Use the power cord that corresponds to the wall outlet in your country. •...
Part Names and Functions Numbers in refer to the main pages in this owner’s manual where the topic is explained. Projector Top View Power 29, 53 indicator STANDBY- 28, 29 ON button For turning the power on and putting the projector into standby mode.
Numbers in refer to the main pages in this owner’s manual where the topic is explained. Rear View Terminals Refer to “INPUT Terminals and Connectable Main Equipment” on page 21. OUTPUT (INPUT 1, 2) terminal (Shared computer RGB and component signals output terminal for INPUT 1 and 2) Terminal for connecting a monitor.
Page 18
Part Names and Functions (Continued) Numbers in refer to the main pages in this owner’s manual where the topic is explained. STANDBY button For putting the projector into the standby mode. KEYSTONE button For entering the Keystone Correction mode. RETURN button For returning to the previous menu screen during menu operations.
Inserting the Batteries Press the P mark on the cover and slide it in the direction of the arrow. Insert the batteries. • Insert the batteries making sure the polarities correctly match the m and n marks inside the battery compartment. Attach the cover and slide it until it clicks into place.
Quick Start This section shows the basic operation (projector connecting with the computer). For details, see the page described below for each step. Setup and Projection In this section, connection of the projector and the computer is explained using one example. 1.
Page 21
4. Adjust the projected image with the Setup Guide After the projector turns on, the Setup Guide appears. (When “Setup Guide” is set to “On”. n page 45) Follow the steps in the Setup Guide and adjust the focus, screen size, and height (angle). After adjusting the focus, height (angle) and screen size, press pENTER to finish the Setup Guide.
“Screen Size and Projection Distance”. Ceiling-mount Setup I It is recommended that you use the optional EIKI ceiling-mount bracket for this installation. Before mounting the projector, contact your nearest EIKI Authorized Dealer or Service Center to obtain the recommended ceiling- mount bracket (sold separately).
Connections INPUT Terminals and Connectable Main Equipment INPUT 1, 2 terminal I Connecting the computer. (See page 23.) I Connecting video equipment with compo- nent output terminal (DVD player, DTV decoder, DVD recorder with hard disc, etc.). (See page 24.) AUDIO (INPUT 1, 2) terminal Connecting an audio cable (Shared audio input terminal for...
Samples of Cables for Connection • For more details of connection and cables, refer to the owner’s manual of the connecting equipment. • You may need other cables or connectors not listed below. Input Equipment Signal Computer video Computer audio Audio-visual Compo- equipment...
Connecting to a Computer Before connecting, ensure that the power cord of the projector is unplugged from the AC outlet and turn off the devices to be connected. After making all connections, turn on the projector and then the other devices. When connecting a computer, ensure that it is the last device to be turned on after all the connections are made.
Connecting to Video Equipment The projector is equipped with input terminals that support component, S-video, and video signals. See the illustration below to connect with the audio-visual equipment. The image quality is highest in the order of the component signal, the S-video signal and the video signal.
When using a composite video cable (INPUT4) To audio output terminal To video output terminal RCA audio cable (com- mercially available) Connecting to a Monitor with RGB Input Terminal You can display computer images on both the projector and a separate monitor using two sets of RGB cables.
Controlling the Projector by a Computer When the RS-232C terminal on the projector is connected to a computer with a DIN-D-sub RS- 232C adaptor and an RS-232C serial control cable (cross type, commercially available), the com- puter can be used to control the projector and check the status of the projector. Refer to the “SETUP MANUAL”...
When connecting to the LAN terminal using a LAN cable Computer LAN cable (Category 5 type, commercially available) Note • When connecting to a hub, use a straight-through Category 5 (CAT.5) type cable (commercially available). • When connecting to a computer, use a cross-over Category 5 (CAT.5) type cable (commercially available).
Turning the Projector On/Off Turning the Projector on Note that the connections to external equip- ment and power outlet should be done be- fore performing the operations written be- low. (See pages to 27.) Remove the lens cap and press o STANDBY-ON on the projector or fON on the remote control.
Turning the Power off (Put- ting the Projector into Standby Mode) Press oSTANDBY-ON on the pro- jector or eSTANDBY on the re- mote control, then press that but- ton again while the confirmation message is displayed, to put the projector into standby mode. Unplug the power cord from the AC outlet after the cooling fan stops.
Image Projection About the Setup Guide After turning on the projector, the Setup Guide screen appears to assist you with projector setup. Guidance items 1 FOCUS 2 HEIGHT ADJUST 3 ZOOM Press pENTER to exit the Setup Guide screen. Note •...
3 Adjusting the Height The height of the projector can be ad- justed using the adjustment feet at the front and rear of the projector. When the screen is above the projec- tor, the projection image can be made higher by adjusting the projector. Lift the projector to adjust its height while lifting the HEIGHT ADJUST lever.
Image Projection (Continued) Switching the Input Mode Select the appropriate input mode for the connected equipment. PressC INPUT DINPUT 3 or EINPUT 4 on the remote control to select the input mode. • When pressing INPUT (P/R) on the projector, input mode switches in the following order: INPUT1 INPUT2 INPUT3...
Correcting Trapezoidal Distortion When the image is projected either from the top or from the bottom towards the screen at an angle, the image becomes distorted trapezoidally. The function for correcting trapezoidal distortion is called Keystone Correction. Note • The Keystone Correction can be adjusted up to an angle of approximately ±13 degrees and the screen can also be set up to an angle of approximately ±13 degrees (when the resize...
Image Projection (Continued) Resize Mode This function allows you to modify or customize the resize mode to enhance the input image. De- pending on the input signal, you can choose “NORMAL”, “BORDER” or “STRETCH” image. Press HRESIZE. • See page for setting on menu screen.
Page 39
VIDEO • “STRETCH” is fixed when 540P, 720P or 1080I signals are entered. Input Signal DVD / Video Image type 4:3 aspect ratio Letter box 480I, 480P, 576I, 576P, NTSC, PAL, SECAM Squeezed 16:9 image Squeezed 4:3 image 16:9 aspect ratio 540P, 720P, 1080I 16:9 aspect ratio (4:3 aspect ratio in...
Operating with the Remote Control Adjustment buttons (P/R/O/Q) Displaying and Setting the Break Timer Press k BREAK TIMER. • The timer starts to count down from 5 minutes. ROn-screen display Press P /R /O /Q to adjust the length of the break time. •...
Menu Items The following shows the items that can be set in the projector. “Picture” menu INPUT 1 (RGB)/INPUT2 (RGB) Picture Net. Picture Mode Standard Contrast Bright Blue CLR Temp 7 5 0 0 Bright Boost Lamp Setting Bright Reset SEL./ADJ.
Page 42
Pict. Network Password Disable DHCP Client TCP/IP MAC Address 0 0 : 0 B : 2 C : 0 1 : 0 0 : 0 0 Projector EIP-3000N SEL./ADJ. ENTER Main menu Help PRJ - ADJ Page 100% Main menu...
Page 43
“Help” menu Pict. Net. There is no picture or audio Vertical stripes or flickering image appear Data image is not centered Color is faded or poor Picture is dark The image is distorted Reset all adjustments to default settings SEL. ENTER The items you can set with the “Help”...
Using the Menu Screen ENTER button Adjustment buttons (P/R/O/Q) MENU/HELP button Menu Selections (Adjustments) Example: Adjusting “Bright”. • This operation can also be performed by using the buttons on the projector. Press BMENU. • The “Picture” menu screen for the se- lected input mode is displayed.
Page 45
Press P or R and select “Bright” to adjust. • The selected item is highlighted. To adjust the projected image while watching it Press hENTER. • The selected item (e.g. “Bright”) is dis- played by itself at the bottom of the screen.
2 Adjusting the Image Adjustment O button Items Contrast For less contrast. Bright For less brightness. Red* For weaker red. Blue* For weaker blue. Color* For less color intensity. Tint* For making skin tones purplish. Sharp* For less sharpness. Bright Boost* For high fidelity color reproduc- tion.
Adjusting the Projected Image (“SCR - ADJ” menu) 1 Setting the Resize Mode Note • For details of the Resize mode, see pages and 35. • You can also press HRESIZE on the remote control to set the resize mode. (See page 34.) 2 Adjusting the Image Position You can move the projected image vertically.
INPUT/VOLUME/AV MUTE/FREEZE/ AUTO SYNC/RESIZE/PICTURE MODE/ “An invalid button has been pressed.” are not displayed. 5 Selecting the Background Image Selectable items Description Logo EIKI logo screen Blue Blue screen None — 6 Selecting the Setup Guide Selectable items Description Displaying the Setup Guide when turning the projector on.
Adjusting the Projector Function (“PRJ - ADJ” menu) 1 Auto Search Function This function automatically searches for and switches to the input mode in which signals are being received, when the projector is turned on, or when the INPUT button is pressed. Note When “Auto Search”...
Info • If you lose or forget your keycode, contact your nearest EIKI Authorized Dealer or Service Center (see page 61). Even if the product warranty is valid, the keycode reset will incur a charge.
Adjusting the Projector Function (“PRJ - ADJ” menu) (Continued) Press the 4 buttons on the remote control or on the projector to en- ter the new keycode in “New Code”. Note • You can not use the following buttons for keycode: •...
DHCP Client TCP/IP MAC Address 0 0 : 0 B : 2 C : 0 1 : 0 0 : 0 0 Projector EIP-3000N SEL./ADJ. ENTER Enter the password in “Old Pass- word” using P, R, Q and O, then press hENTER.
Factory default setting: 000. 000. 000. 000 * When not in use, set to “000. 000. 000. 000”. equipment computers. Projector Information Description The MAC address of the projector is displayed. The projector name is displayed. (Factory preset : EIP-3000N)
Troubleshooting with the “Help” menu This function advises you to solve the problems during usage. Utilizing the “Help” menu func- tions Example: When image flickering appears Operation to solve image flickering when pro- jecting the computer RGB signal. Press BMENU/HELP. Press O or Q to select “Help”, then press hENTER.
Maintenance Cleaning the projector I Ensure that you have unplugged the power cord before cleaning the projector. I The cabinet as well as the operation panel is made of plastic. Avoid using benzene or thinner, as these can damage the finish on the cabinet.
Maintenance Indicators I The warning lights (power indicator, lamp indicator and temperature warning indicator) on the projector indicate problems inside the projector. I If a problem occurs, either the temperature warning indicator or the lamp indicator will illuminate red, and the projector will enter standby mode. After the projector has entered standby mode, follow the procedures given below.
Page 58
• Relocate the projector to an area with proper ventilation. (see page 8) • Take the projector to your nearest EIKI Authorized Dealer or Service Center (see page 61) for repair. • Disconnect the power cord from the AC outlet, and then connect it again.
I Carefully change the lamp by following the instructions described in this section. * If you wish, you may have the lamp replaced at your nearest EIKI Authorized Dealer or Service Center. * If the new lamp does not light after replacement, take your projector to the nearest EIKI Authorized Dealer or Service Center for repair.
Regarding the Lamp (Continued) Removing and Installing the Lamp Unit Warning! • Do not remove the lamp unit from the projec- tor right after use. The lamp and parts around the lamp will be very hot and may cause burns or injury.
Remove the lamp unit. • Loosen the securing screws from the lamp unit. Hold the lamp unit by the handle and pull it in the direction of the arrow. At this time, keep the lamp unit horizontal and do not tilt it. Insert the new lamp unit.
Computer Compatibility Chart Computer • Multiple signal support Horizontal Frequency: 15-70 kHz, Vertical Frequency: 45-85 Hz, Pixel Clock: 12-108 MHz Sync signal:Compatible with TTL level • Compatible with sync on green signal The following is a list of modes that conform to VESA. However, this projector supports other signals that are not VESA standards.
Troubleshooting Problem • Projector power cord is not plugged into the wall outlet. • Power to the external connected devices is off. • The selected input mode is wrong. • Cables incorrectly connected to the projector. • Remote control battery has run out. •...
Page 64
Troubleshooting (Continued) Problem • Change the input signal type setting. Picture is green on INPUT 1 (COMPONENT)/ • When you cannot select an input signal type, select “Color is faded INPUT 2 (COMPONENT). Picture is pink (no green) on INPUT 1 (RGB)/INPUT 2 (RGB).
U.K., RGB cable, DIN-D-sub RS-232C adaptor, 3 RCA to 15-pin D-sub cable, Quick Guide, Owner’s manual (Printed and CD-ROM) As a part of policy of continuous improvement, EIKI reserves the right to make design and specification changes for product improvement without prior notice. The performance specifica- tion figures indicated are nominal values of production units.