Motorola MSC8101 ADS User Manual page 118

SM73228X = (F_PD[] == 2);-- 8MByte
-- Declare 4 Flash Banks:
FLASH_BANK1 = ( SM73228X # (SM73248X & !A8) # ( SM73288X & !A7 & !A8)) ;
FLASH_BANK2 = ((SM73248X & A8) # (SM73288X & !A7 & A8)) ;
FLASH_BANK3 = (A7 & !A8 & SM73288X) ;
FLASH_BANK4 = (A7 & A8 & SM73288X) ;
-- Assign the appropriate Flash Chip Select:
F_Cs1~ = !((!F_Cs0~ & FLASH_BANK1 & FROM_FLASH_CNFG_WORD) #
(!F_Cs0~ & FLASH_BANK1 & !FROM_FLASH_CNFG_WORD & !FROM_HOST_CNFG_WORD & HARD_RESET_ACTIVE~));
F_Cs2~ = !((!F_Cs0~ & FLASH_BANK2 & FROM_FLASH_CNFG_WORD) #
(!F_Cs0~ & FLASH_BANK2 & !FROM_FLASH_CNFG_WORD & !FROM_HOST_CNFG_WORD & HARD_RESET_ACTIVE~));
F_Cs3~ = !((!F_Cs0~ & FLASH_BANK3 & FROM_FLASH_CNFG_WORD) #
(!F_Cs0~ & FLASH_BANK3 & !FROM_FLASH_CNFG_WORD & !FROM_HOST_CNFG_WORD & HARD_RESET_ACTIVE~));
F_Cs4~ = !((!F_Cs0~ & FLASH_BANK4 & FROM_FLASH_CNFG_WORD) #
(!F_Cs0~ & FLASH_BANK4 & !FROM_FLASH_CNFG_WORD & !FROM_HOST_CNFG_WORD & HARD_RESET_ACTIVE~));
%
******************************************************************************
* MODCK[1-3] DRIVEN
******************************************************************************
%
MODCK_TRI[1..3]= (MODCK1r,MODCK2r,MODCK3r);
BNK_TRI[2]= TRI(MODCK_TRI[1], !HARD_RESET_ACTIVE~);
BNK_TRI[1]= TRI(MODCK_TRI[2], !HARD_RESET_ACTIVE~);
BNK_TRI[0]= TRI(MODCK_TRI[3], !HARD_RESET_ACTIVE~);
MODCK_BNK[0..2]= BNK_TRI[0..2];
%
******************************************************************************
* BOOT FROM SERIAL EEPROM
******************************************************************************
%
EEPROM_ENABLE = !SBOOT_EN~ # (BTM0 AND !BTM1);
IF (FETHIEN~ AND EEPROM_ENABLE) THEN SBOOTEN_OUT~ = GND;
ELSE
END IF;
%
******************************************************************************
* DRIVE PORESET IMPULSE (RECONFIG USING BCSR4)
******************************************************************************
%
DivEn.s = GND; DivEn.r = GND;
DivEn.prn = !(MPC_WRITE_BCSR_4 & (D[0..1] == B"10")) & !END_OF_WD_TIMER;
-- Preset to FF when write b'10 bit to BCSR4
DivEn.clrn = !END_OF_IMPULSE & PRST~;
END_OF_IMPULSE = POR_IMPULSE1.dv2 & POR_IMPULSE1.dv4 & POR_IMPULSE1.dv8 & POR_IMPULSE1.dv16 &
POR_IMPULSE2.dv2 & POR_IMPULSE2.dv4 & POR_IMPULSE2.dv8 & POR_IMPULSE2.dv16;
POR_IMPULSE1.g = VCC;
POR_IMPULSE2.g = VCC;
POR_IMPULSE2.clk = POR_IMPULSE1.dv16;
POR_IMPULSE1.clr = !DivEn.q; -- Start first cascade divider if zero
POR_IMPULSE2.clr = !DivEn.q; -- Start second cascade divider if zero
R_PORI~ = OPNDRN(!DivEn.q);
%
******************************************************************************
* WATCHDOG FOR AUTO RECONFIGURATION
******************************************************************************
% -- WD Start/Stop by writing B"01xxxxxx" into BCSR4
-- when count value will be achived PORESET is forced
MOTOROLA
Freescale Semiconductor, Inc.
(1 X 8 MByte bank )
SBOOTEN_OUT~ = VCC;
-- Drive PORESET with updated MODCK values
MSC8101ADS RevB User's Manual
For More Information On This Product,
Go to: www.freescale.com
-- boot from serial EEPROM
C-117