CAME F1000 Installation Manual
Ferni series automation for swing gates
Hide thumbs
Also See for F1000:
- Installation manual (49 pages) ,
- Standard installation (16 pages) ,
- Manaul (16 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for CAME F1000
Summary of Contents for CAME F1000
- Page 1 AUTOMATION 119D69 EN FOR SWING GATES INSTALLATION MANUAL F1000 - F1100 English...
-
Page 2: Read Carefully
Warning Sings (e.g. gate plate). (i.e. that for which it was expressly built for). Any other use is Special instructions and to be considered dangerous. Came Cancelli Automatici S.p.A. advice for users is not liable for any damage resulting from improper, wrongful •... -
Page 4: Legend Of Symbols
*Whenever the shutter is over 2,5 m., it needs an electrical lock F1000; F1100 always needs it. 3 Reference Standards The company: CAME cancelli automatici is ISO 9001 quality certified; is has also obtained the ISO 14001 environmental safeguar- ding certification. CAME engineers and manufactures all of its products in Italy. -
Page 5: Installation
4.3 Description of parts 1) Base plate 2) Gearmotor assembly 3) Motor cover 4) Articulated transmission arm Optional accessory : F1001 Straight telescopic arm (for single gate wings that are 0,5 to 2 m max long). 4.4 Overall dimensions 5 Installation Installation must be carried out by expert qualified personnel and in full compliance with current regulations. -
Page 6: Standard Installation
5.2 Tools and materials Make sure you have all the tools and materials you will need for the installation at hand to work in total safety and compliance with the current standards and regulations. The following figure illustrates the minimum equipment needed by the installer. 5.3 Cable list and minimum thickness Connection Type of cable Cable length 1 <... - Page 7 5.5 Mounting - Secure the base plate to the pillar using ø8 screws and ø14 moulded inserts making sure the minimum distance of 150mm from the ground is met. - Secure the A bracket (using ø8 screws or by welding) to the gate leaf making sure the 450mm and 19mm distances measurements and are met.
- Page 8 - Insert the straight semi-arm into the motor shaft. Apply the fl ared washer, the M6x20 screw and lock the semi-arm using the two grub screws. Join and secure the two arms using the washer and M8x16 screw. Release the motor (see p. 7) and secure the curved semi-arm to the “A”...
- Page 9 5.7 Adjusting the closing and opening-speed brake microswitches During opening: release and move the door to the open position desired. Turn the upper cam until the microswitch is activated and screw the microswitch is activated and screw the screw in the related cam. During closure (F 1000 only): release the door and move it to the desired closing position.
-
Page 10: Safety Instructions
5.9 Connecting to the ZA3N/ZF1N/ZM3E control panel Motor terminals Control panel terminal board Ground 6 Safety instructions Important safety instructions This product must only be employed for its originally intended use. Any other use is wrong and potentially dangerous. The manufacturer cannot be held liable for any damages resulting from wrongful, erroneous or negligent uses. -
Page 11: Maintenance
7 Maintenance 7.1 Periodic maintenance Periodic maintenance to be carried out by the end-user is as follows: wipe clean the glass surface of the photocells; check that the safety devices work properly; remove any obstructions. We suggest checking the state of lubrication and tightness of the anchoring screws on the operator. To check the efficiency of the safety devices, move an object in front of the photocells when gate is closing. - Page 12 Periodic maintenance log for end-user (every 6 moths) Signature Date Notes 7.3 Extra-ordinary maintenance The following table serves to note down any extraordinary maintenance, repairs or improvements performed by specialised firms. N.B.: Any extraordinary maintenance must be performed by specialised technicians. Extra-ordinary maintenance log Installer’s stamp Operator name...
-
Page 13: Demolition And Disposal
CAME CANCELLI AUTOMATICI S.p.A. employs a UNI EN ISO 14001 certified and compliant environmental protection system at its plants, to ensure that environmental safeguarding. We ask you to keep protecting the environment, as CAME deems it to be one of the fundamental points of its market operations strategies, by simply following these brief guidelines when disposing: DISPOSING THE PACKING MATERIALS The packing components (cardboard, plastic, etc.) are solid urban waste and may be disposed of without any particular difficulty, by... - Page 14 CAME Rus C/juan De Mariana, N. 17-local Umc Rus Llc 28045 Madrid Ul. Otradnaya D. 2b, Str. 2, o ce 219 CAME UNITED KINGDOM LTD (+34) 91 52 85 009 127273, Moscow UNIT 3, ORCHARD BUSINESS PARK TOWN STREET, SANDIACRE...