Summary of Contents for THE WORLD MODELS ZERO FIGHTER EP
Page 1
INSTRUCTION MANUAL ZERO FIGHTER EP Requires : 5-channel radio w/ 5 micro servos, Outrunner Motor KM0283010 w/ Propeller Adaptor HW2340100, 20A brushless ESC, 3 cells 11.1V 2100 mAh Li - Po battery & charger. S p ecifica tio n s Wing Span 39.5 in / 1000 mm...
ZERO FIGHTER EP INDEX BEFORE YOU BEGIN PARTS LIST ASSEMBLY P.3-P.9 SAFETY PRECAUTIONS BEFORE YOU BEGIN Read through the manual before you begin, so you will have an overall idea of what to do. Check all parts. If you find any defective or missing parts contact your local dealer. Please DRY FIT and check for defects for all parts that will require CA or Epoxy for final assembly.
Main Wing Apply instant type CA glue to both sides of each hinge. Aileron Servo Lead Bottom View Aileron Servo Lead Retractable Landing Gear Bottom View E216XMPO23721004...
Please refer to attached sheet for linkage connector installation. Retract Servo Linkage connector To R-Side To L-Side Plywood 2x7x21mm Wheels Down Position 16mm Travel 16mm Travel Wheels Up Position Ø1mm pilot holes for World Models tri-horn are pre-drilled. Please look for pin-hole Aileron Servo marks at under side of control surfaces.
Vertical Fin, Rudder & Tail Landing Gear PA2x8mm WHEEL Ø23mm PA2x8mm Screw Plastic Collar Bottom View 1.2mm C=C' Completed Apply instant type CA glue to both sides of each hinge. Ø1mm pilot holes for World Models horn are pre-drilled. Rudder Pushrod Please look for pin-hole marks at under side of control surfaces.
Elevator Pushrod Ø1mm pilot holes for World Models horn are pre-drilled. Please look for pin-hole marks at under side of control surfaces. PB2x8mm Screw TWM PL8210010 CLEVIS WRENCH 55mm PB2x8mm Fuel Tube 12mm d2xD4x4mm Pushrod Ø1.4x365mm Clevis Bottom View Horn Outrunner Motor / Cowling KP0011310 Solder...
Page 8
Radio equipment J1(Pushrod Ø1.4x52mm) Elevator Servo J2(Pushrod Ø1.4x365mm) Pushrod Connector Front Elevator Pushrod Elevator Servo Receiver Ø1.4x365mm Install and arrange the Straper servo as shown in the diagram. Elevator Pushrod Ø1.4x52mm Rudder Pushrod Fuel Tube Sponge Battery Tie Ø1.4x430mm d2xD4x4mm Rudder Servo Bottom View KA1.7x6mm...
Page 9
Canopy Lazyback Antenna Pilot PWA2x8mm Screw Lazyback Antenna PWA2x8mm 1.5mm Wing Setting Adjust the wing and fuselage configuration as shown in the diagrams. A=A' B=B' C=C' D=D' E216XMPO23721004...
Page 10
# First time flyer should never fly by himself / herself. Assistance from experienced flyer is absolutely necessary. # Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly pre-adjusted aircraft. ZERO FIGHTER EP is specially designed to be powered by KM0283010 Outrunner Motor.
Page 11
Product Registration Form (US Customers) We would like to share with you any relevant information regarding your model, including product news and free upgrade parts when applicable. Please fill in the following and send to AirBorne Models, 4749-K, Bennett Drive, Livermore, CA 94551 USA. 1.
Optional Parts ACCESSORIES) 3 - Pin EZ Connector 2 - Pin EZ Connector Code No. Size Package Code No. Size Package KP0011310 40A Max. Current 1 set KP0011210 40A Max. Current 1 set -ideal for electric models -ideal for electric models Propeller Adaptor Wrench Propeller Adaptor Code No.
Need help?
Do you have a question about the ZERO FIGHTER EP and is the answer not in the manual?
Questions and answers