Table of Contents
Advertisement
Quick Links
0.46 cu. in. displacement 2 - stroke
Radio required: 4-channel radio w/ 5 sdandard servos
Wing Span
Wing Area
Flying Weight
Fuselage Length
Warning! This model is not a toy.
It is designed for maximum performance. Please seek advice if one is not familiar with this kind
of engine powered precision model. Operating this model without prior preparation may cause
injuries. Remember, safety is the most important thing. Always keep this instruction manual at
hand for quick reference.
The World Models
Manufacturing Co., Ltd.
www.theworldmodels.com
A088SPO30511508
Specifications
80.5 in / 2040 mm
1232 sq in / 79.5 sq dm
8.6 Ib / 3900 g
65.5 in / 1670 mm
*Specifications are subject to change without notice.*
INSTRUCTION MANUAL
( A088S )
FACTORY PRE-FABRICATED
ALMOST-READY-TO-FLY(ARF)SERIES
MADE IN CHINA
Advertisement
Table of Contents
Related Manuals for THE WORLD MODELS Super Frontier Senior A088S
Summary of Contents for THE WORLD MODELS Super Frontier Senior A088S
- Page 1 Operating this model without prior preparation may cause injuries. Remember, safety is the most important thing. Always keep this instruction manual at hand for quick reference. FACTORY PRE-FABRICATED The World Models ALMOST-READY-TO-FLY(ARF)SERIES Manufacturing Co., Ltd. MADE IN CHINA www.theworldmodels.com...
- Page 2 INDEX BEFORE YOU BEGIN PARTS LIST ASSEMBLY P.3-P.11 SAFETY PRECAUTIONS P.12 BEFORE YOU BEGIN Read through the manual before you begin, so you will have an overall idea of what to do. Check all parts. If you find any defective or missing parts contact your local dealer. Please DRY FIT and check for defects for all parts that will require CA or Epoxy for final assembly.
- Page 3 Parts List 1. MAIN WING -- 1 pair 13. SOCKET HEAD SCREW M3x30mm -- 4 pcs WASHER d3xD7mm -- 8 pcs 2. SCREW PB2x20mm -- 4 pcs M3 NUT -- 8 pcs FUEL TUBE Ø6x5mm -- 4 pcs THROTTLE PUSH WIRE Ø1.2x445mm -- 1 pc. CLEVIS PL4112103 -- 2 pcs PLASTIC TUBE d2xD3x200mm -- 1 pc.
-
Page 4: Aileron Servo
Main Wing Aileron Servo Lead Pre-glued Bottom View Aileron Servo Ø1mm pilot holes for World Models horn are pre-drilled. Please look for pin-hole PB2x20mm Screw marks at under side of control surfaces. Straper TWM PL8210010 CLEVIS WRENCH Fuel Tube D6x5mm Pushrod Ø1.8x130mm PB2x20mm... - Page 5 Fuselage Covering Decal Stabilizer / Elevator Remove coverings for all surfaces in contact before applying A/B epoxy glue. Pre-glued Vertical Fin / Rudder Remove coverings for all surfaces in contact before applying A/B epoxy glue. Pre-glued B=B' A088SPO30511508...
-
Page 6: Landing Gear
Landing Gear PM4x40mm Screw M3x16mm M3x16mm Socket Head Screw KA2.3x8mm Screw d3xD7mm Washer d2xD8mm Quick Release Nylon Rivet Bottom View Completed d4xD9mm Washer Quick Release Nylon Rivet Wheel Ø76mm Washer d4xD9mm KA2.3x8mm Set Screw d3xD7mm Washer Set Screw d4xD9mm Washer 4.1mm Collar Wheel... -
Page 7: Fuel Tank
Fuel Tank Cable Tie 1.5x5x400mm Fuel Tank 380CC Double-sided Tape 40x110mm Bottom View Nose Landing Gear PA3x14mm Screw PA3x14mm Steering Arm Stand Plywood 3x25x30mm Wind Shield PA2.3x8mm Screw d1.5xD6.5mm Silicon Grommet Canopy PWA2.3x8mm PWA2.3x8mm Fuselage Silicon Grommets Silicon Grommets A088SPO30511508... - Page 8 Nose Landing Gear 3mm Set Screw 4.6mm Collar PA2.6x10mm Screw 4.1mm Collar 4.6mm Collar 3mm Set Screw Steering Arm Nose Landing Gear Plastic Tube d2xD3x200mm Wheel Pant Nose Wheel Steering Pushrod Ø1.6x320mm 4.6mm Collar PA2.6x10mm 3mm Set Screw Mounting Plate 4.6mm Collar Wheel Ø76mm Engine...
- Page 9 Cowling Battery Cover PWA2.6x12mm Screw d1.5xD6.5mm Silicon Grommet First insert the grommet to the cowling then apply screw. Spinner Ø52mm Fuselage Cowling PWA2.6x12mm PWA2.6x12mm Silicon Grommets d1.5x6.5mm Silicon Grommet Windows Windows Servo Set 3x3mm Set Screw 3x3mm Set Screw Throttle Pushwire Linkage Connector Washer Washer...
-
Page 10: Elevator Pushrod
Elevator Pushrod Ø1m m pilot holes for Wor ld Models hor n ar e pr e-dr illed. Please look for pin-hole m ar ks at under side of contr ol sur faces. PB2x16mm Screw TWM PL8210010 CLEVIS WRENCH Pushrod Ø1.8x1135mm PB2x16mm Fuel Tube D6x5mm... -
Page 11: Radio Equipment
Radio Equipment Install and arrange the servos as shown in the diagram. Press down the center 1/3 portion Plastic Tube Copper Tube Rigging Z Bend d2xD3x200mm Ø1.2x27mm Nose Wheel Throttle Pushrod Steering Pushrod Throttle Servo Ø1.2x445mm Ø1.6x320mm Front Straper Fuel Tube Sponge Battery Rudder Pushwire... - Page 12 Main Wings M3x30mm Socket Head Screw d3xD12mm Washer M3x30mm Plywood 3x40x120mm Completed d3xD12mm Washer Wing Setting A=A` B=B` C=C` D=D` A088SPO30511508 P.11...
-
Page 13: Control Throws
Control Throws Adjust the control throws as shown in the diagram. These throws are good for general flying. You can adjust according to your personal preference. Elevator 29mm 29mm Rudder 35mm 35mm Ailerons 12mm 12mm C.G. The ideal C.G. position is 100mm ( 3.94 in. ) behind the leading edge measured at where the wing meets the fuselage. - Page 14 LINKAGE CONNECTOR HW7111050 & HW7111060 Drill 2mm hole at servo horn. Insert linkage connector into servo horn. Make sure shoulder of screw is cleared from servo horn. Add washer to reduce play if necessary. Shoulder Tighten up the round nut against the shoulder.
-
Page 15: Optional Parts
Optional Parts ACCESSORIES) 180mm Extension Clevis Wrench Code No. Size Package Code No. Size Package PL8210010 1 set KW0011800 180mm 1 set Large Clevis Small Clevis Special tool for clevis installation. Suitable for standard and small (EP) clevis. 180mm Y-Cord Code No. - Page 16 The World Models Manufacturing Co., Ltd. www.theworldmodels.com A088SPO30511508...
Need help?
Do you have a question about the Super Frontier Senior A088S and is the answer not in the manual?
Questions and answers