1. Manuals
  2. Brands
  3. SIG Manuals
  4. Toy
  5. SIGRC95ARF Fokker D.VII
  6. Assembly manual

SIG SIGRC95ARF Fokker D.VII Assembly Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SIGRC95ARF Fokker D.VII and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for SIG SIGRC95ARF Fokker D.VII

Summary of Contents for SIG SIGRC95ARF Fokker D.VII

  • Page 2: Assembly Instructions

    Fokker D.VII was the only aircraft specifically mentioned in Aricle IV as a weapon that must be entirely destroyed or confiscated. The SIG Fokker D.VII represents the aircraft flown by Lt. August von Raben, Commanding Officer of Jasta 18 from March to November 1918.

  • Page 3: Kit Contents

    1 . . .Fokker L/G Spreader Wing 2 . . .Wing Reinforcing Strips (1-1/4” x 20-1/4”) Bag #7: SIGRPMGDU293 1 . . .SIG 180 Class Power System Bag #3: 3 . . #3 x 10mm Phillips-Head Screws 1 . . .Fokker Molded Plastic Hatch Cover SIGRPCC295 1 .

  • Page 4: Tools And Supplies

    HiTEC equipment listed. Watch the weight of components carefully as using heavier than recommended equipment will have a very detrimental effect on the flight performance of your Sig Fokker D.VII. Electronic Speed Control (ESC)... We show the installation and use of a MAXX Products MX-9105 ESC in this manual. Other ESC units may be used, provided they have a minimum rating of 5 amps.

  • Page 5: Battery Charger

    Battery Charger: The charger for the flight battery pack is one of the most critical pieces of equipment for flying electric powered airplanes. Having the correct charger and using it properly can make the difference between an electric airplane that flies well and one that can’t even get off the ground.
  • Page 6 4...Use 5-minute epoxy to glue the Firewall & plywood Firewall, the 2 Cowl Mounts, Cowl Mounts the Servo Tray, the Tailskid, and the 2 Servo Tray Aluminum Wing Tubes in place in the fuselage. NOTE: Be sure the firewall is firmly seated into the recess molded into the front of the fuselage.
  • Page 7 To apply the decals, leave the clear plastic in position while you cut the individual mark- ing from the main sheet. When ready to apply the decal, remove the clear plastic and place the decal in the desired location, adhe- sive side down.
  • Page 8 To operate the system, first turn on the Rudder Servo transmitter and place the throttle stick in the Elevator Servo full low position. Now plug the airborne battery pack into the "battery" side of the ESC. The system should now be operational (see Motor NOTE below).
  • Page 9 17...Plug the two servos and the ESC back into the correct Antenna Exit Hole Receiver Is Under Foam receptacles in the receiver. Place the receiver on the bottom of the fuselage, in front of the servos. Cut a piece of soft foam rubber (not furnished) to fit over the receiver and hold the receiver in place.
  • Page 10 22..Apply the Wing Reinforcing Tape (14mm X 43mm) to the 20...Trim the plastic Hatch Cover as shown. Test fit the leading edge of both the top and bottom wing. The tape should be trimmed Hatch Cover onto the top of the fuselage and adjust as centered on the leading edge left and right and should be applied needed for a good fit.
  • Page 11 23...Apply the Wing Reinforcing Strips (1-1/4” x 20-1/4”) onto the leading edges of both the top and bottom wings. The strips should be centered left-to-right on the leading edge, and should be applied so that it wraps around the leading edge, with half its width on top and half its width on the bottom of the wing.
  • Page 12 For more information contact: ACADEMY OF MODEL AERONAUTICS model. SIG MFG. CO.’s obligation shall be to replace those parts of the kit proven to be defective or missing. The user shall determine the suitability of the product for his or her 5161 East Memorial Drive;...

Table of Contents