Precautions for use
Cautions when installing
Do not set up the Display outdoors.
The Display is designed for indoor use.
•
Environmental temperature to use this unit
When using the unit where it is below 1 400 m (4 593
•
ft) above sea level: 0 °C to 40 °C (32 °F to 104 °F)
When using the unit at high altitudes (1 400 m (4 593
•
ft) and higher and below 2 800 m (9 186 ft) above sea
level): 0 °C to 35 °C (32 °F to 95 °F)
Do not install the unit where it is 2 800 m (9 186 ft)
and higher above sea level.
Failure to do so may shorten the life of the internal
•
parts and result in malfunctions.
Required space for ventilation
When using the pedestal (optional accessory), leave
a space of 10 cm (3
right, and 5 cm (1
31/32
keep the space between the bottom of the display and
the floor surface.
If using some other setting-up method (wall-hanging,
etc.), follow the manual of it. (If there is no specific
indication of installation dimension in the installation
manual, leave a space of 10 cm (3
top, bottom, left and right, and 5 cm (1
the rear.)
Minimum distance:
a
a
About the screws used when using a wall hanging
bracket that conforms to VESA standards
Inch
Screw pitch for
model
installation
55
400 mm × 400 mm
49
400 mm × 400 mm
42
200 mm × 200 mm
When installing, do not use the screw holes
(situated at the bottom of the display's back) as
shown in the following figures.
It may damage the LCD panel.
55-inch model
12
English
") or more at the top, left and
15/16
") or more at the rear, and also
") or more at the
15/16
") or more at
31/32
a: 10 cm
(3
a
b
b: 5 cm
(1
Depth of
screw
hole
10 mm
10 mm
10 mm
49-inch model
42-inch model
Be careful of the movable structure of the power
indicator and remote control sensor.
As factory default, the power indicator and remote
•
control sensor are stored in the main unit. For normal
use, pull out the remote control sensor from the edge
side of the main unit by operating the lever on the
rear panel. Depending on the setup condition such as
when using the multi display, store the remote control
sensor in the main unit. (see page 32)
Do not grab the liquid crystal panel.
Do not forcibly press the liquid crystal panel, or push
•
it with a pointed object. Applying a strong force to
the liquid crystal panel will cause unevenness of the
screen display, resulting in malfunction.
Depending on the temperature or humidity
conditions, uneven brightness may be observed.
This is not a malfunction.
This unevenness will disappear while applying current
•
continuously. If not, consult the distributor.
Request Regarding Security
")
15/16
When using this product, take safety measures
against the following incidents.
")
31/32
Personal information being leaked via this product
•
Unauthorized operation of this product by a malicious
•
third party
Interfering or stopping of this product by a malicious
•
third party
Screw
Take sufficient security measures. (see page 54, 98)
(quantity)
Set a password for the LAN control and restrict the
•
M6 (4)
users who can log in.
M6 (4)
Make your password difficult to guess as much as
•
possible.
M6 (4)
Change your password periodically.
•
Panasonic Corporation or its affiliate companies will
•
never ask for your password directly. Do not divulge
your password in case you receive such inquiries.
The connecting network must be secured by a
•
firewall, etc.
When disposing the product, initialize the data before
•
disposing. [Factory data reset] (see page 59) or
[Shipping] (see page 113)
About Wireless LANs
●
The advantage of a wireless LAN is that information
can be exchanged between a PC or other such
equipment and an access point using radio waves as
long as you are within range for radio transmissions.