Dremel 8100 Original Instructions Manual page 21

ENVIRONMENT
DISPOSAL
The machine, accessories and packaging should be sorted
for environmental-friendly recycling.
ONLY FOR EC COUNTRIES
Do not dispose of power tools into household
waste!
According the European Guideline 2012/19/EC for
Waste Electrical and Electronic Equipment and its
implementation into national right, power tools
that are no longer usable must be collected
separately and disposed of in an environmentally
correct manner.
SPECIFICATIONS
GENERAL SPECIFICATIONS
Voltage Rating . . . . . . . . . 7,2 V
Amperage Rating . . . . . . 1,3 – 1,5 Ah
Rated Speed . . . . . . . . . . n 33000 min
Collet Capacity . . . . . . . . 0,8 mm, 1,6 mm, 2,4 mm,
SPECIFICATIONS CHARGER
Input. . . . . . . . . . . . . . . . . 230 V, 50 – 60 Hz, 26 W
Output . . . . . . . . . . . . . . . 3,6 V - 10,8 V
EXTENSION CORDS
Use completely unrolled and safe extension cords with a
capacity of 5 Amps.
ASSEMBLY
ALWAYS TURN OFF THE TOOL BEFORE CHANGING
ACCESSORIES, CHANGING COLLETS, OR SERVICING
THE TOOL.
IMPORTANT CHARGING NOTES
1. The charger was designed to fast charge the battery
only when the battery temperature is between 32°F
)0°C( and 113°F )45°C(. If the battery pack is too hot
or too cold, the charger will not fast charge the battery.
)This may happen if the battery pack is hot from
heavy use(. When the battery temperature returns to
between 32°F )0°C( and 113°F )45°C(, the charger will
automatically begin charging.
2. A substantial drop in operating time per charge may
mean that the battery pack is nearing the end of its life
and should be replaced.
3. Remember to unplug charger during storage period.
NOTE: Use of chargers or battery packs not sold by
Dremel will void the warranty.
CHARGING BATTERY PACK (MODEL 808)
Plug charger cord into your standard power outlet.
With no battery pack inserted, the charger's green indicator
light will go ON. This indicates the charger is receiving
power and the charger is ready for operation.
-1
3,2 mm
, 1,5 A
PICTURE 2
A. Tool
B. Battery pack
C. Battery release tabs
To remove the battery pack from the tool press both
battery release tabs and pull the battery from the tool.
When you insert the battery pack into the charger, the
charger's green indicator light will begin to "BLINK". This
indicates that the battery is receiving a fast charge.
PICTURE 3
A. Battery pack
B. Charger
C. Green light
When the indicator light stops "BLINKING" )and becomes
a steady green light( fast charging is complete. The
battery pack is fully charged and can be removed from the
charger.
When you begin the charging process of the battery pack,
a steady green light could also mean the battery pack is
too hot or too cold.
Fast charging is only possible when the temperature range
of the battery pack is between 0°C and 45°C.
When needed, the internal fan of the charger will turn on to
aid the charging process and speed.
As soon as the battery pack reaches the correct
temperature range, the battery charger will automatically
switch to fast charging.
The battery pack may be used even though the light may
still be blinking. The light may require more time to stop
blinking depending on temperature.
The purpose of the green light is to indicate that the
battery pack is fast-charging. It does not indicate the exact
point of full charge. The light will stop blinking in less time
if the battery pack was not completely discharged.
If the green indicator light is "ON", the battery pack cannot
accept a charge.
The Dremel multitool is a high quality precision tool that
can be used to perform detailed and intricate tasks. The
wide range of Dremel accessories and attachments allow
you to perform a large variety of tasks. These include tasks
such as sanding, carving, engraving, routing, cleaning and
polishing.
PICTURE 1
A. Shaft lock button
B. On/Off and variable speed slide switch
C. Battery pack
D. Battery release tabs
E. Ventilation openings
F. Housing
G. Battery pack
H. Battery release tabs
I. Shaft
J. EZ Twist™ integrated wrench/nose cap
K. Collet nut
L. Collet
M. Wrench
The Dremel accessories available for the multitool come
with various shank sizes. Four size collets are available to
accommodate the different shank sizes. Collet sizes are
identified by the rings on the back of the collet.
21
GENERAL
COLLETS