Table of Contents
Advertisement
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
Security Codes
The system supports up to seven security codes; Installer, Master, four secondary user, and Duress, described as follows:
Code
Installer (User 1)
Master (User 2)
Secondary Users 3-6
Duress (User 8)
Keypad Functions
The following is a brief list of system commands. For detailed information concerning system functions, refer to the User's Manual.
Function or Keypad Display
Silence Alarms
Disarmed, Not Ready
Arming AWAY
Arming STAY
Arming INSTANT
Arming MAXIMUM
Quick Arming (if enabled)
Disarming
Bypassing Zones
Forced (Quick) Bypass (if enabled)
Chime Mode
Arming Mode
AWAY
STAY
INSTANT
MAXIMUM
Description of Code Function and Programming
The factory default Installer Code is "4-1-1-1", but may be changed in field 20. The Installer code
cannot be used to disarm the security system if it was not used to arm the system. The Installer code
must be used to program the 4-digit Master Code.
The Master security code permits access to the system for arming, disarming, etc. Opening and closing
reports are sent for the Master Code as No. 02, with the appropriate subscriber number.
•
To assign a Master Code, enter Installer Code + 8 + 2 + 4-digit Master Code.
•
To change the Master Code, enter Master Code + 8 + 2 + New Master Code + New Master Code
Only the Master code can be used to assign, change, or delete the secondary 4-digit user codes.
Secondary User codes permit access to the system for arming, disarming, etc.
•
To assign (or change) a Secondary security code, enter Master Code + [CODE] key + User No.
(3–6) + desired 4-digit Secondary Code.
To delete a Secondary security code, enter Master Code + [CODE] key + User No. (3–6).
Secondary user codes are sent as Nos. 3 through 6 respectively, with the appropriate subscriber number.
Intended for use when forced to arm or disarm the system under threat. When used, the system will act
normally, but can silently notify the central station, if that service has been provided.
•
To program a Duress code, enter Master code + [8] key + [8] key + new 4-digit Duress Code.
•
To change a Duress code, enter Master code + [8] key + [8] key + desired 4-digit Duress Code.
•
To delete a Duress code, enter Master code + [8] key + [8] key and stop.
The Duress Code must differ from the Master Code or any other User's Code.
Description
Pressing any key silences the keypad sounder for 10 seconds. Disarming the system silences
both keypad and external sounders.
Before arming, the system must be in the READY condition (all zones must be intact). If the
NOT READY message appears, press the READY [ ] key to display faulted zones.
Enter 4-digit security code + AWAY [2] key.
Enter 4-digit security code + STAY [3] key.
Enter 4-digit security code + INSTANT [7] key.
Enter 4-digit security code + MAXIMUM [4] key.
Simply press [#] key in place of code, then press AWAY, STAY, INSTANT, or MAXIMUM to
arm system as desired. Note that the [#] key cannot be used in place of the 4-digit security code
when disarming the system.
Enter 4-digit security code + OFF [1] key.
Enter 4-digit security code + BYPASS [6] key + zone number(s).
To automatically bypass all faulted zones, use the "Quick Bypass" method: Enter 4-digit
security code + BYPASS, then wait for all open zones to be displayed. Arm when display
indicates Bypass and Ready to Arm.
Enter 4-digit security code + CHIME [9] key. To turn chime off, enter code + CHIME again.
SUMMARY OF ARMING MODES
Exit
Delay
Yes
Yes
Yes
Yes
System Operation
Features for Each Arming Mode
Entry
Perimeter
Delay
Armed
Yes
Yes
No
No
S E C T I O N
Interior
Armed
Yes
Yes
Yes
No
Yes
No
Yes
Yes
1 0
10-1
Advertisement
Table of Contents
