Dahua IPC-HDBW5502N Quick Start Manual
  1. Manuals
  2. Brands
  3. Dahua Manuals
  4. Security Camera
  5. IPC-HDBW5502N
  6. Quick start manual
Dahua IPC-HDBW5502N Quick Start Manual

Dahua IPC-HDBW5502N Quick Start Manual

Hd (ir) vandal proof network dome camera
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
HD (IR) Vandal Proof Network Dome Camera
Quick Start Guide
Version 1.3.0

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the IPC-HDBW5502N and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Dahua IPC-HDBW5502N

Summary of Contents for Dahua IPC-HDBW5502N

  • Page 1 HD (IR) Vandal Proof Network Dome Camera Quick Start Guide Version 1.3.0...
  • Page 2 Welcome Thank you for purchasing our network camera! This quick start guide is designed to be a reference tool for your system. Please keep this start guide well for future reference. Please open the accessory bag to check the items one by one in accordance with the list below. Contact your local retailer ASAP if something is missing or damaged in the bag.
  • Page 3 Thunder-proof device is recommended to be adopted to better prevent thunder. The grounding studs of the product are recommended to be grounded to further enhance the reliability of the camera. 6. Daily Maintenance Please shut down the device and then unplug the power cable before you begin daily maintenance work.

  • Page 4: Table Of Contents

    Table of Contents Structure ............................1 Dimensions ........................1 Port Description ......................1 Bidirectional talk......................7 1.3.1 Device-end to PC-end ..................7 1.3.2 PC-end to the Device-end ..................7 Alarm Setup ........................8 Installation..........................10 Device Installation Introduction ................10 Device Installation Steps ...................

  • Page 5: Structure

    1 Structure 1.1 Dimensions You can refer to the following figures for dimension information. The Unit is mm. See Figure 1-1 and Figure 1-2. Figure 1-1 Dimension 1 Figure 1-2 Dimension 2 1.2 Port Description For the non-IR series product, the interface is shown as in Figure 1-3 and Figure 1-4. Note：...
  • Page 6 Figure 1-3 Camera internal without IR (1-a) Figure 1-4 Camera internal without IR (1-b) See Figure 1-5.
  • Page 7 Figure 1-5 Camera internal without IR (2) See Figure 1-6, Figure 1-7 and Figure 1-8. Figure 1-6 Motorized focus camera internal with IR (1-a)
  • Page 8 Figure 1-7 Motorized focus camera internal with IR (1-b) Figure 1-8 Motorized focus camera internal with IR (2) See Figure 1-9, Figure 1-10 and Figure 1-11.
  • Page 9 Figure 1-9 Manual focus camera internal with IR (1-a) Figure 1-10 Manual focus camera internal with IR (1-b)
  • Page 10 Figure 1-11 Manual focus camera internal with IR (2) Please refer to the following sheet for external connection port definition information. Port Port Name Connector Function Description AC 24V power POWER Connect to AC 24V power. port DC 12V power POWER Connect to DC 12V power.

  • Page 11: Bidirectional Talk

    Default input is DC 12V.  network port external connected cable.  Connect to standard Ethernet port.  Support PoE. Network port Ethernet port Note: Before making crystal head, pull the anti-dust cover through network cable. Please refer to the following sheet for I/O port cable function information. Note: actual product may vary.

  • Page 12: Alarm Setup

    Connect the speaker or the MIC to the audio input port of the PC and then connect the earphone to the audio output port of the device. Login the Web and then click the Talk button to enable the bidirectional talk function. You can see the button becomes orange after you enabled the audio talk function.
  • Page 13 Figure 1-13 Alarm input Please refer to the following figure for alarm output information. See Figure 1-14. Port ALARM_COM and Port ALARM_NO composes an on-off button to provide the alarm output. If the type is NO, this button is normal open. The button becomes on when there is an alarm output. If the type is NC, this button is normal off.

  • Page 14: Installation

    2 Installation Important  Before you complete the installation and setup, do not remove the electrostatic attraction film on the transparent enclosure. Otherwise it may result in injury.  After remove electrostatic attraction film, do not touch dome enclosure in case it may leave stain.

  • Page 15: Device Installation Steps

    Figure 2-2 2.2 Device Installation Steps 2.2.1 Installation Steps for Devices of Following Product Models: HDB/HDBW3202, HDB/HDBW3101, HDB/HDBW5202, HDB/HDBW5302, HDB/HDBW5502, HDB/HDBW8301, HDB/HDBW8306. The interface is shown as in Figure 2-3. IR Motorized Zoom Lens Series Non-IR Series IR Manual Zoom Series Figure 2-3 Step 1 Take the installation position map from the accessories bag and then paste it on the installation ceiling...
  • Page 16 Use the inner hex wrench from the accessories bag to unfasten the 3 hex screws on the dome camera enclosure to open it. Step 3 Please remove the device cable (Provided) network port and the power terminal. Use the inner hex wrench (Provided) to remove the 2 inner hex screws from the dome driver module.
  • Page 17 Step 5 Please refer to the Step 3 to put the driver module back to the metal hooks of the chassis. Then use the inner hex wrench to secure the two inner hex screws to the chassis. Then connect the network cable and the power terminal.

  • Page 18: Manual Zoom Lens Focus Operation

    Figure 2-7 c). Lens tilt rotation angle. Please refer to Figure 2-8 to unfasten the lock screw B and lock screw C and adjust the tilt monitor angle to the proper position. Then fix the lock screw B and lock screw C. The tilt angle ranges from -23°...

  • Page 19: Side Cable Exit

    Step 1 Slightly loosen the adjusting screw E and push the adjust screw E to make it swing. Adjust the lens focus to the proper position according to the displayed video. Step 2 Slightly loosen the adjusting screw F and push the adjust screw F to make it swing. Adjust the lens to get the clear video and then fix the adjusting screw firmly.

  • Page 20: Cable Connection

    side panel. Please remove the plastic decoration plug from the side panel of the chassis and pull through the cable to the tunnel of the PG11 screw thread. Now secure the tunnel in the PG11 screw threaded hole of the device. 2.2.4 Cable Connection The device reserves two cable exits.
  • Page 21 Figure 2-12 Step 1 Take the installation position map from the accessories bag and then paste it on the installation ceiling or the wall according to the monitor area. Please dig three bottom holes of the plastic expansion bolts according to the map. Take three expansion bolts from the accessories bag and then insert them to the holes you just dug and then fix firmly.
  • Page 22 a) For the IR series product, you can skip current step and go the step b) directly. For the non-IR series product, push the port slightly to remove the decoration enclosure from the black plastic enclosure. See Figure 2-13. Figure 2-13 b) Lens pan rotation angle setup.

  • Page 23: Manual Zoom Lens Focus Operation

    Lock screw B/C Adjust lens tilt rotation angle. Lock screw D Adjust image pan rotation angle. Lock screw A Adjust lens pan rotation angle. Figure 2-14 Step 5 Line up the dome camera protection enclosure to the cable exit on the side panel. Put the enclosure back and then use the inner hex wrench to secure the 3 inner hex screws firmly.

  • Page 24: Side Cable Exit

    Step 1 Slightly loosen the adjusting screw E and push the adjust screw E to make it swing. Adjust the lens focus to the proper position according to the displayed video. Step 2 Slightly loosen the adjusting screw F and push the adjust screw F to make it swing. Adjust the lens to get the clear video and then fix the adjusting screw firmly.

  • Page 25: Micro Sd Card Installation

    Figure 2-16 Step 2 Before you go to the Step 3 in the chapter 2.2.5 installation steps, please pull through cable with the waterproof airproof plug to the device chassis via the installation hole at the bottom of the chassis and then connect the cable pins.
  • Page 26 Step 3 Please refer to Step 7 in chapter 2.2.1 to put the device protection enclosure back.

  • Page 27: Quick Configuration Tool

    3 Quick Configuration Tool 3.1 Overview Quick configuration tool can search current IP address, modify IP address. At the same time, you can use it to upgrade the device. Please note the tool only applies to the IP addresses in the same segment. 3.2 Operation Double click the “ConfigTools.exe”...
  • Page 28 In the configuration tool search interface (Figure 3-1), please select a device IP address and then double click it to open the login interface. Or you can select an IP address and then click the Login button to go to the login interface. See Figure 3-3. In Figure 3-3, you can view device IP address, user name, password and port.

  • Page 29: Web Operation

    4 Web Operation This series network camera products support the Web access and management via PC. Web includes several modules: Monitor channel preview, system configuration, alarm and etc. 4.1 Network Connection Please follow the steps listed below for network connection. ...
  • Page 30 Figure 4- 2 Web login After you successfully logged in, please install WEB plug-in unit. Please refer to the Web Operation Manual included in the resource CD for detailed operation instruction. See Figure 4- 3. Figure 4- 3 Web monitoring window...

  • Page 31: Appendix Toxic Or Hazardous Materials Or Elements

    Appendix Toxic or Hazardous Materials or Elements Toxic or Hazardous Materials or Elements Component Name Cr VI PBDE Circuit Board ○ ○ ○ ○ ○ ○ Component ○ ○ ○ ○ ○ ○ Device Case ○ ○ ○ ○ ○ ○...

Table of Contents