Dahua H Series Quick Start Manual
Ir dome network camera
Hide thumbs
Also See for H Series:
- Quick start manual (19 pages) ,
- User manual (404 pages) ,
- Quick start manual (20 pages)
Related Manuals for Dahua H Series
Summary of Contents for Dahua H Series
- Page 1 Quick Start Guide Model H IR Dome Network Camera Quick Start Guide ZHEJIANG DAHUA VISION TECHNOLOGY CO., LTD. V1.0.2...
-
Page 2: Foreword
Quick Start Guide Foreword General This manual introduces the functions, installation, and operations of the camera. Safety Instructions The following categorized signal words with defined meaning might appear in the manual. Signal Words Meaning Indicates a medium or low potential hazard which, if not avoided, could result in slight or moderate injury. - Page 3 Quick Start Guide All trademarks, registered trademarks and the company names in the manual are the properties of their respective owners. Please visit our website, contact the supplier or customer service if there is any problem occurred when using the device. If there is any uncertainty or controversy, please refer to our final explanation.
-
Page 4: Important Safeguards And Warnings
Quick Start Guide Important Safeguards and Warnings Electrical Safety All installation and operation should conform to your local electrical safety codes. The power source shall conform to the Safety Extra Low Voltage (SELV) standard, and supply power with rated voltage which conforms to Limited Power Source requirement according to IEC60950-1. - Page 5 Quick Start Guide It is recommended to ground the device to enhance reliability. Do not touch the image sensor (CMOS) directly. Dust and dirt could be removed with air blower, or you can wipe the lens gently with soft cloth that moistened with alcohol. Device body can be cleaned with soft dry cloth, which can also be used to remove stubborn ...
-
Page 6: Table Of Contents
Quick Start Guide Table of Contents Foreword ................................I Important Safeguards and Warnings ......................III 1 Introduction ..............................1 Device Ports ....................................1 Connecting Alarm Input/output ............................2 2 Network Configuration ..........................4 Initializing Device ..................................4 Modifying Device IP Address ..............................5 Logging in to Web Interface.............................. -
Page 7: Introduction
Quick Start Guide Introduction Device Ports Device ports might vary with different models, and the actual product shall prevail. Waterproof all the cable joints with insulating tape and waterproof tape to avoid short circuit and water damage. For the detailed operation, see the FAQ Manual. Figure 1-1 Device ports For more information about device ports, see Table 1-1. -
Page 8: Connecting Alarm Input/Output
Quick Start Guide Table 1-2 Alarm I/O port introduction Port Port Name Description Receives the switch signal of external alarm source. ALARM_IN (pin1–pin3) GND (pin4) Connect all the alarm input devices to the same GND port. Alarm I/O Outputs alarm signal to alarm output device. ALARM_NO1 (pin5) ALARM_NO2 (pin7) ALARM_COM1 (pin6) - Page 9 Quick Start Guide Figure 1-3 Alarm output Step 3 Log in to web interface, and configure alarm input and alarm output in alarm setting. The alarm input on the web interface is corresponding to the alarm input end of the I/O ...
-
Page 10: Network Configuration
Quick Start Guide Network Configuration Device initialization and IP address setting can be finished with the "ConfigTool" or on web interface. For more information, see the WEB Operation Manual. Device initialization is available on select models, and it is required at first use or after the device being reset. -
Page 11: Modifying Device Ip Address
Quick Start Guide The Device initialization interface is displayed. Step 6 Select the devices that need initialization, and then click Initialize. The password setting interface is displayed. See Figure 2-2. Figure 2-2 Password setting Step 7 Set and confirm the password of the devices, then enter a valid email address, and then click Next. -
Page 12: Logging In To Web Interface
Quick Start Guide After clicking Search setting, enter the username and password, and make sure that they are the same as what you set during initialization; otherwise there will be wrong password notice. Step 2 Select the devices whose IP addresses need to be modified, and then click Modify IP. The Modify IP Address interface is displayed. - Page 13 Quick Start Guide Figure 2-4 Main interface...
-
Page 14: Installation
Quick Start Guide Installation Packing List The tool required for the installation such as electric drill is not provided in the package. The operation manual and related tool are contained in the disk or the QR code, and the actual ... -
Page 15: Installing Device
Quick Start Guide Installing Device 3.3.1 Installation Method 3.3.2 Installing SD Card (Optional) Disconnect the power before installing or removing the SD card. Press and hold the reset button for 10 s to reset the camera. 3.3.3 Threading Cable This section takes threading network cable for example. -
Page 16: Attaching Device
Quick Start Guide 3.3.4 Attaching Device Make sure that the mounting surface is strong enough to hold at least three times of the weight of the device and bracket. - Page 17 Quick Start Guide Cable going through the mounting surface...
-
Page 18: Wrapping Waterproof Tape (Optional)
Quick Start Guide Cable going through the side cable tray 3.3.5 Wrapping Waterproof Tape (Optional) This part is needed when the cable connector is out of the junction box. -
Page 19: Adjusting Lens Angle
Quick Start Guide 3.3.6 Adjusting Lens Angle... - Page 20 Quick Start Guide...