Related Manuals for ACME LP-1600 BD30
Summary of Contents for ACME LP-1600 BD30
- Page 1 TV LIGHT PANEL 1600 LP-1600 BD30 User Manual Please read the instructions carefully before use...
-
Page 3: Table Of Contents
TABLE OF CONTENTS 1. Safety Instructions 2. Technical Specifications 3. How To Set The Fixture 4. How To Control The Fixture 5. DMX 512 Configuration 6. DMX 512 Connections 7. Troubleshooting 8. Fixture Cleaning... - Page 4 1. Safety Introductions Please read the instructions carefully which includes important information about the installation, operation and maintenance. WARNING Please keep this User Manual for future consultation. If you sell the unit to another user, be sure that they also receive this instruction booklet. ...
-
Page 5: Technical Specifications
serving, as the unit could be very hot Do not touch any wire during operation as high voltage might be causing electric shock. Due to the magnifying type lens, please keep the lens out of contact with direct sunlight. Direct sunlight can cause heat to build up inside of the unit, which will seriously damage unit. -
Page 6: How To Set The Fixture
The equipment must be fixed by professionals. And it must be fixed at a place where is out of the touch of people and has no one pass by or under it. 4. How To Set The Fixture 4.1 Control Panel ○... - Page 7 ○ 7 DMX input: For DMX512 link, use 3/5-pin XLR plug cable to input DMX signal ○ 8 Mains input: Connect to supply mains power 4.2 Main Function To select any functions, press MENU button until the required one is shown on the display. Select the function by ENTER button and the display will blink.
- Page 8 DMX 512 Address setting Press the MENU button up to when the is shown on the display. Pressing ENTER button and the display will blink. Use DOWN and UP button to change the DMX 512 address. Once the address has been selected, press ENTER button to setup or automatically exit menu mode without any change after 8 seconds.
- Page 9 Once select, press ENTER button to setup or automatically exit menu mode without any change after 8 seconds. To go back to the functions without any change press the MENU button. Dimmer curve Press the MENU button up to when the is shown on the display，Pressing ENTER button and the present mode will blink.
- Page 10 Display Inverse Press MENU button until is blinking on the display. Use DOWN and UP button to select (normal) or (inverse), press ENTER button to setup. Back to the functions without any change press MENU button. Self-Test Press the MENU button up to when the is blinking on the display.
-
Page 11: Dmx512 Configuration
5.2 DMX Controller An universal DMX controller to control the units, you have to set DMX address from 1 to 512 channel so that the units can receive DMX signal. Press the MENU button up to when the is showing on the display. Pressing ENTER button and the display will blink. -
Page 12: Dmx512 Connections
7. DMX512 Connections The DMX512 is widely used in intelligent lighting control, with a maximum of 512 channels. Connect the fixture together in a “daisy chain” by XLR plug cable from the output of the fixture to the input of the next fixture. The cable cannot be branched or split to a “Y” cable. -
Page 13: Troubleshooting
8. Troubleshooting Following are a few common problems that may occur during operation. Here are some suggestions for easy troubleshooting: A. The fixture does not work, no light 1. Check the connection of power and main fuse. 2. Measure the mains voltage on the main connector. B. - Page 15 EC - Declaration of Conformity We declare that our products (lighting equipments) comply with the following specification and bears CE mark in accordance with the provision of the Electromagnetic Compatibility (EMC) Directive 89/336/EEC. EN55014-2: 1997 A1: 2001, EN61000-4-2: 1995; EN61000-4-3: 2002; EN61000-4-4: 1995;...
- Page 16 Innovation, Quality, Performance...
Need help?
Do you have a question about the LP-1600 BD30 and is the answer not in the manual?
Questions and answers