Appendix; Troubleshooting; Troubleshooting Digital Broadcasting - Sharp 60X50H Operation Manual

Appendix

Troubleshooting

The problems described below are not always caused by malfunctions. Check the TV again before having the TV
serviced.
Problem
• No power.
• Unit cannot be operated.
• Remote control unit does not
operate.
• Picture is cut off.
• Strange colour, light colour, or
dark, or colour misalignment.
• Power is suddenly turned off.
• No picture.
• No sound.
• The TV sometimes makes a
cracking noise.
• Cannot select the desired channel. • Switch between Digital TV and Analogue TV modes. (See page 43.)
Troubleshooting
Problem
• No picture or no sound.
• Block noise appears on the screen.
• D-TV broadcasts cannot be received.
• A specifi c channel cannot be received.
• No broadcast now
Cautions regarding use in high and low temperature environments
• When the unit is used in a low temperature space (e.g. room, offi ce), the picture may leave trails or appear slightly delayed.
This is not a malfunction, and the unit will recover when the temperature returns to normal.
• Do not leave the unit in a hot or cold location. Also, do not leave the unit in a location exposed to direct sunlight or near a
heater, as this may cause the cabinet to deform and the LCD panel to malfunction.
Storage temperature: f20°C to e60°C.
84
60X50H_en_ID5.indd 84 60X50H_en_ID5.indd 84
• Is the AC cord disconnected? (See page 15.)
• Has the power been turned on? (See page 19.)
• When the power switch does not work, remove the power plug and insert it again,
and press POWER a on the TV after waiting more than fi ve seconds.
• External infl uences such as lightning, static electricity, etc., may cause improper
operation. In this case, operate the unit after fi rst turning the power off the TV or
unplugging the AC cord and re-plugging it in after 1 or 2 minutes.
• Are batteries inserted with polarity (e, f) aligned? (See page 18.)
• Are batteries worn out? (Replace with new batteries.)
• Are you using it under strong or fl uorescent lighting?
• Is a fl uorescent light shining on the remote control sensor?
• Is the image position correct? (See page 39.)
• Are screen mode adjustments such as picture size made correctly? (See pages 34,
35, 68 and 82.)
• Adjust the picture tone. (See pages 37 to 39.)
• Is the room too bright? The picture may look dark in a room that is too bright.
• Check the colour system setting. (See pages 25 and 59.)
• Check the "HDMI auto view" setting. (See page 57.)
• The unit's internal temperature has increased.
Remove any objects blocking the vent or clean.
• Check the "ECO" setting. (See pages 33 and 34.)
• Is the sleep timer set? (See page 33.)
• Is the connection to external equipment correct? (See pages 16 and 17.)
• Is the correct input selected? (See page 58.)
• Is the picture adjustment correct? (See pages 37 to 39.)
• Is the antenna connected properly? (See page 15.)
• Is "On" selected in "Audio only"? (See page 28.)
• Is the volume too low? (See page 23.)
• Make sure that headphones are not connected. (See page 13.)
• This is not a malfunction. This happens when the cabinet slightly expands and
contracts according to changes in temperature. This does not affect the TV's
performance.
Digital broadcasting
–
Error code
—
E202
—
E203
Possible solution
Possible solution
• Is the correct Input source selected? (See page 58.)
• Is the antenna pointing in the correct direction?
• Check the "Signal strength" and "Quality". (See page 20.)
• Are physical objects blocking the antenna?
• Is the antenna or antenna cable compatible with D-TV broadcast?
• Is the D-TV antenna set up properly?
• Is the antenna cable connected properly? (See page 15.)
• Is the channel settings correct? (See page 20.)
• Check the "Signal strength" and "Quality". (See page 20.)
• Check the current broadcast.
2011-6-13 17:20:21 2011-6-13 17:20:21