Section 3-3-2: Venting Components - Montigo H38DF PRC Installation & Maintenance Manual

Section 3-3-2:
VENTING COMPONENTS
The following components and associated Montigo part num-
bers for installation of a roof or wall mounted termination. Use
only Montigo Vent Components. Use of non-Montigo parts will
VOID the warranty and may impede operation of the fireplace..
Connection and installation of the vent components
should adhere to the following guidelines:
Use any combination of rigid and flex pipe as required and in
„
any orientation (Male connectors can face in any direction).
Flex sections may be stretched up to 50% of their total length
„
(e.g. a 24" section maybe stretched to 36").
Connect all vent sections using a minimum of three sheet
„
metal screws on the outer pipe flue.
Ensure the pipe ends male to female slide in a minimum of
„
1 1/2" of overlap.
Ensure all horizontal runs are supported with a minimum
„
of 3 supports per 10' of venting.
When hanging/ supporting venting, ensure that 1" clearance
„
is maintained on sides and bottom of vent runs and 2" above
horizontal vent runs to any combustible material.
Rigid pipe may be cut less than half way from the female
„
end only.
Ensure when cutting sections of rigid pipe to maintain
„
integrity of internal supports.
Place the springs, supplied with the pipe kit, between the
„
outer and inner pipes to keep the pipes separate and avoid
any possible hot spots.
Montigo recommends the use of a flex section for the final
„
pipe connected directly to the fireplace offering greater
flexibility of installation and absorption of movement.
Firestops must be installed as required by National & local
„
codes .
Montigo recommends that all exterior corners and joints be
„
sealed with exterior caulking. However, we encourage you to
consult your Building Envelope Engineer or Waterproofing
Consultant for further recommendations.
IMPORTANT:
Please Refer to your Building Envelope
Engineer or Waterproofing Consultant
for a review of ALL penetrations through
exterior walls or the roof.
XG0211 - 151126
Installation
A - Termination
B - Frame Kits
C - Flex Sections
D - Rigid Sections
E - Elbows
F - Support Ring & Plate PSPXT-8
G - Firestop
H - Roof Flashing
I - Heat Shield
J - Heat Guard
H*38DF PRC Panorama Indoor Gas Fireplace
PTO4 (3" Length)
PTO4F (3" Length)
PVTK1SS
MSR (Stucco Frame)
MOSR (Stucco Frame)
BSR-4 (4" Brick Frame)
BSR-6 (6" Brick Frame)
PFL - 1 (12" f/f Section)
PFL - 18 (18" f/f Section)
PFL - 2 (24" f/f Section)
PFL - 3 (36" f/f Section)
PFL - 4 (48" f/f Section)
PFL - 6 (72" f/f Section)
PXT - 5 (5" f/f Section)
PXT - 10 (10" f/f Section)
PXT - 20 (20" f/f Section)
PEXT - 1 (12" f/m Section)
PEXT - 2 (24" f/m Section)
PEXT - 3 (36" f/m Section)
PEXT - 4 (48" f/m Section)
PEXT - 6 (72" f/m Section)
PEL-90MM (m/m 90º Elbow)
PEL-90FF ( f/f 90º Elbow)
PEL-90FM ( f/m 90º Elbow)
PEL-45FM ( f/m 45º Elbow)
FS-8
PRF-7 (1/12 - 7/12 pt.)
PRF-12 (7/12 - 12/12 pt.)
RHS101
MTKOG
Page 17