Montigo H38DF PRC Installation & Maintenance Manual
Montigo H38DF PRC Installation & Maintenance Manual

Montigo H38DF PRC Installation & Maintenance Manual

Panorama indoor residential gas fireplace
Table of Contents

Advertisement

Installation & Maintenance Manual
DANGER
Read and understand this manual. Improper installation, adjustment, alteration,
service or maintenance can cause serious injury, property damage or even death.
For assistance or additional information consult a qualified installer, service
agency or the gas supplier.
Glass doors on gas fireplaces are extremely hot while the fireplace is on and
remain hot even after the fireplace has been turned off. Safety screens are
available and can reduce the risks of severe burns. Please keep children away
from the fireplace at all times.
XG0211
CAUTION
®
C
US
Canadian Heating Products Inc. Langley, BC V4W 4A1 | Montigo Del Ray Corp. Ferndale, WA 98248
H38DF PRC
HL38DF PRC
HP38DF PRC
Panorama
Indoor
Residential
Gas Fireplace
WARNING
Do not store or use gasoline or any other flammable vapors and liquids in the vicinity of
this or any other gas burning appliance. A fire or explosion my occur causing serious
injury, property damage or even death.
NOTICE
Installer: Leave this manual with the appliance. Do not remove.
Consumer: Retain this manual for maintenance and future reference. Do not Discard.
DANGER
Blank
IF YOU SMELL GAS
Blank
Flammable materials
Explosion risk
Toxic
Corrosive
Danger overhead crane
Fork lift trucks
High voltage
Do not try to light any appliance.
Blank
Flammable materials
Explosion risk
Toxic
Corrosive
Danger overhead crane
Fork lift trucks
High voltage
Do not touch any electrical switch; do not use any phone in your building.
General Warning
Laser Radiation
Biohazard
Oxidising
Hot surface
Danger of entrapment
Danger of death
Flammable materials
Explosion risk
Immediately call your gas supplier from a neighbor's phone. Follow the gas
Toxic
Corrosive
Danger overhead crane
Fork lift trucks
High voltage
General Warning
Laser Radiation
Biohazard
Oxidising
Hot surface
Danger of entrapment
Danger of death
Irritant
Slippery floor
Watch your step
Cutting
High temperatures
Glass hazard
Danger of suffocation
Blank
supplier's instructions.
General Warning
Laser Radiation
Biohazard
Oxidising
Hot surface
Danger of entrapment
Danger of death
Irritant
Slippery floor
Watch your step
Cutting
High temperatures
Glass hazard
Danger of suffocation
Gas bottles
Watch for
Electricity
Danger for cutter
Entrapment hazard
Battery hazard
Rotating parts
Flammable materials
falling objects
Explosion risk
Toxic
Corrosive
Danger overhead crane
Fork lift trucks
High voltage
If you cannot reach your gas supplier, call the fire department.
Irritant
Slippery floor
Watch your step
Cutting
High temperatures
Glass hazard
Danger of suffocation
Gas bottles
Watch for
Electricity
Danger for cutter
Entrapment hazard
Battery hazard
Rotating parts
Low temperature
Strong magnetic field
falling objects
Optical radiation
Non ionizing
Radiation
Hazardous to the
Danger of harming
radiation
Environment
your hands
General Warning
Laser Radiation
Biohazard
Oxidising
Hot surface
Danger of entrapment
Danger of death
Gas bottles
Watch for
Electricity
Danger for cutter
Entrapment hazard
Battery hazard
Rotating parts
Low temperature
Strong magnetic field
falling objects
Optical radiation
Non ionizing
Radiation
Hazardous to the
Danger of harming
radiation
Environment
your hands
Irritant
Slippery floor
Watch your step
Cutting
High temperatures
Glass hazard
Danger of suffocation
Low temperature
Strong magnetic field
Optical radiation
Non ionizing
Radiation
Hazardous to the
Danger of harming
radiation
Environment
your hands
Gas bottles
Watch for
Electricity
Danger for cutter
Entrapment hazard
Battery hazard
Rotating parts
falling objects
040912.1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the H38DF PRC and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Montigo H38DF PRC

  • Page 1 Danger of harming radiation Environment your hands Gas bottles Watch for Electricity Danger for cutter Entrapment hazard Battery hazard Rotating parts falling objects XG0211 040912.1 Canadian Heating Products Inc. Langley, BC V4W 4A1 | Montigo Del Ray Corp. Ferndale, WA 98248...
  • Page 2: Table Of Contents

    H*38DF PRC Panorama Indoor Gas Fireplace NOTICE You must read and understand this manual prior to installation, operation or troubleshooting this appliance. Please retain this owner’s manual for furure reference and maintenance. Table of Contents INTRODUCTION .................3 Section 4: Wiring ................18 BEFORE YOU START: ...............4 ▪...
  • Page 3: Introduction

    Refer to your rating plate to Congratulations on your purchase of a Montigo Fireplace. verify included options. Throughout this manual instructions With over 30 years of experience, Montigo is committed to providing H*38PR* are applicable to all models designated as...
  • Page 4: Before You Start

    Should it be impossible to meet the venting requirements laid „ BEFORE YOU START: out in Section 3: Venting, please contact a local Montigo dealer regarding the use of a Montigo Power Vent. Lay out the Vent run; calculating the required elbows and straight „...
  • Page 5: Section 1: Installation Overview And Product Dimensions

    H*38DF PRC Panorama Indoor Gas Fireplace Installation Section 1: Installation Overview and Product Dimensions Safety, as well as efficiency of operation, should be considered when Please review the Pre-Installation Checklist on Page 4 for general selecting the fireplace location. Select a location that does not interfere information on preparing for a successful installation of your fireplace.
  • Page 6: Section 2: Framing The Fireplace

    H*38DF PRC Panorama Indoor Gas Fireplace Installation Section 2: Framing Frame in the enclosure for the unit with framing materials. The Top Vent framed opening for the assembled fireplace is 40 3/4" wide, x 44" Ceiling level high x 24 1/2" deep, see Figure 2 Non-Combustible materials.
  • Page 7: Clearances

    H*38DF PRC Panorama Indoor Gas Fireplace Installation Nailing Flange Extension Clearances When installing a shelf over the top of the fireplaces, the following The 4" nailing flange extension is shipped attached to the top edge of guidelines must be adhered to: the fireplace, see Figure 1.
  • Page 8: Section 3: The Direct Vent System

    H*38DF PRC Panorama Indoor Gas Fireplace Installation Section 3: Venting Montigo supplies a variety of direct venting and termination options. 3. Install the (removed) Rear flue cover and gasket material, to the The direct vent termination location MUST be selected such that Top vent outlet.
  • Page 9: Installing A Roof Mounted Termination

    H*38DF PRC Panorama Indoor Gas Fireplace Installation Section 3-2: INSTALLING A ROOF MOUNTED DIRECT VENT TERMINATION (PVTK-1) PVTK1 Termination This section applies to installations where the direct vent termi- 2’ min. nation will be roof mounted. Section 3-2-1: VENTING LAYOUT Support ring Selection of components and details of venting lay out should adhere to the following guidelines:...
  • Page 10: Standard Roof Vent (One Elbows No Offsets)

    H*38DF PRC Panorama Indoor Gas Fireplace Installation PVTK1 Termination Storm Collar Support plate 32’ M a. x Support ring 12” Max. Figure 9c. Rear vent, Roof mounted venting (1 = 90° bend). Page 10 XG0211 - 040912.1...
  • Page 11: Installing A Wall Mounted Termination

    H*38DF PRC Panorama Indoor Gas Fireplace Installation 4). Installation of termination from inside structure Section 3-3: INSTALLING A WALL MOUNTED DIRECT VENT A Termination with a MOSR Frame is installed from the inside of the TERMINATION structure. These are commonly used in high-rise construction. This section applies to installations where the direct vent termi- nation will be wall mounted.
  • Page 12: Venting Layout

    If your installation does not fall with in the venting graph parameters, Venting runs must fall within the limits set by the venting graphs, „ please contact a local Montigo see Figure 12 or 12a. dealer for Power Venting options. The Venting Graph Measure the vertical height from the fireplace hearth to the centre of Figure 12a.
  • Page 13: Top Vent, Wall Mounted Hp38Pr* Graph

    H*38DF PRC Panorama Indoor Gas Fireplace Installation 150”max. Heat Shield Termination Solid Section Flex Section Exterior Wall Hearth Figure 13b. H38PR*, HL38PR*, or HP3PR* Top Vented, wall mounted Multi- elbow installation. See Venting Graph for Top vent, wall mounted terminations, Figure 12 or 12a.
  • Page 14: Rear Vent, Wall Mounted Graph, H*38Pr

    Plot on the Venting Graph Figure 14 please contact a local Montigo or 14a with an 'X'. dealer for Power Venting options.
  • Page 15: Rear Vent, Wall Mounted Graph, Hp38Pr

    H*38DF PRC Panorama Indoor Gas Fireplace Installation 46” Max. Flex or Rigid Section 26” Min. 59” Min. 12” Max. 33” Figure 15a. H38PR* or HL38PR* Rear Vented, wall mounted Multi-elbow termination installation. The vent run must comply with the Venting Graph for Rear vent, wall mounted terminations, Figure 14.
  • Page 16: Venting Components

    FS-8 possible hot spots. H - Roof Flashing PRF-7 (1/12 - 7/12 pt.) Montigo recommends the use of a flex section for the final pipe „ PRF-12 (7/12 - 12/12 pt.) connected directly to the fireplace offering greater flexibility of installation and absorption of movement.
  • Page 17: Heat Shields

    H*38DF PRC Panorama Indoor Gas Fireplace Installation Section 3-3-3: Heat Shields Installing a Wall Mounted RHS101 Heat shield. Installing a Wall Mounted RHS8 Heat shield The RHS101 Heat shield MUST be used where the RHS8 Termination The RHS8 Heat shield CANNOT be used when the Termination is WITHIN (Figure 16 and 16a) CANNOT be used.
  • Page 18: Section 4: Wiring

    H*38DF PRC Panorama Indoor Gas Fireplace Installation Section 4: Wiring Models H38DFPRCN-F HL38DFPRCN-F HPDFPRCN-F H38DFPRCL-F HL38DFPRCL-F HP38DFPRCL-F Receiver 14 Battery Holder w/ Switch REMOTE ON/REMONTE/OFF Orange Green Pilot Receiver 14 Receiver 14 Pin Connector Battery Holder Top View (Not Used) RECEIVER 885 Valve SPLIT FLOW...
  • Page 19: Section 5: Installing The Gas Line

    To check pressures, control valves have a provision to remove „ a 1/8” N.PT. plug to be fitted with a hose barb. Montigo requires a service shut off valve be located in an „ accessible location to isolate the gas supply.
  • Page 20: Section 6: Finishing

    H*38DF PRC Panorama Indoor Gas Fireplace Installation Section 6: Finishing Finishing Around the Fireplace Mantels & Surrounds NOTE: National Canadian Gas Association mantel test requirements Combustible mantels and mouldings may be safely installed over the are for fire hazard prevention to combustible materials. top and on the front of the fireplace provided that they do not project beyond shaded area shown in Figure 22.
  • Page 21: Section 7: Installing & Removing The Door

    H*38DF PRC Panorama Indoor Gas Fireplace Installation Section 7: Installing & Removing the Door Removing the door: The H*38PR* doors are removed in a few simple steps. Follow these Step 5: instructions below to remove the Horizontal access panel, unlatch the Ensure the tool is firmly door buckles and, remove the door.
  • Page 22: Section 8: Installing The Accessories

    H*38DF PRC Panorama Indoor Gas Fireplace Installation Section 8: Installing the Accessories Installing the H38PR* Logset The H38PR* is supplied with eight (8) fibre logs. The two small bottom Log C logs ("A" ) are mounted on the burner grate by placing them diagonally onto the supplied Log stands.
  • Page 23: Installing The Hp38Pr* Logset

    H*38DF PRC Panorama Indoor Gas Fireplace Installation Installing the HP38PR* Logs and Embers Log E Bottom Logs The HP38PR* is supplied with seven (7) fibre logs. The two bottom logs ("A" & "B") are mounted on the burner grate as shown in Figure 26a. Top Logs Place logs "C"...
  • Page 24: Installing Firestones

    These may be spaced at random or in a visual pattern of your Figure 28a. Ensure ONLY one layer of firestones cover the preference in the burner tray. See the Montigo web site for photographs burner and no firestones cover the pilot.
  • Page 25: Section 9: Operation

    H*38DF PRC Panorama Indoor Gas Fireplace Operation Section 9: Start up Sequence Standing (Continuous) Pilot Ignition (SIT NOVA 820) with American Flame Electronic Ignition For Your Safety - READ BEFORE LIGHTING: WARNING If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury or death.
  • Page 26: Start-Up Sequence Sit Proflame Gas Valve

    H*38DF PRC Panorama Indoor Gas Fireplace Operation SIT Proflame Electronic Ignition with American Flame Electronic Ignition For Your Safety - READ BEFORE LIGHTING: WARNING If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury or death. A.
  • Page 27: Start-Up Sequence With Honeywell Electronic Ignition

    H*38DF PRC Panorama Indoor Gas Fireplace Operation Honeywell Electronic Ignition with American Flame Electronic Ignition For Your Safety - READ BEFORE LIGHTING: WARNING If the information in these instructions is not followed exactly, a fire or explosion may result causing property damage, personal injury or death. A.
  • Page 28: Maintenance

    H*38DF PRC Panorama Indoor Gas Fireplace Maintenance Hi-Lo Burner Adjustment: (SIT Nova 820). Lighting Instructions The H*38PR* is equipped with an adjustable burner, allowing you to See pages 25 to 27. raise or lower the flames. To adjust the flames, locate the black knob marked 'Hi-Lo', in the centre of the gas control valve (See Figure 29).
  • Page 29: Troubleshooting

    If your fireplace still does not operate correctly, consult your local Montigo dealer. All service and repairs should be performed by a qualified Technician. All spare parts, optional fans, and optional trim finishes are available from your local Montigo dealer. Page 29...
  • Page 30: Replacement Parts

    Contact your local Montigo Dealer Burner Assembly LPG RLG547 RLG547 Logs All service and repairs should be performed by a qualified Technician. All spare parts, optional fans, and optional trim finishes are available from your local Montigo dealer. Page 30 XG0211 - 040912.1...
  • Page 31: Appendix

    H*38DF PRC Panorama Indoor Gas Fireplace Appendix Appendix A: Venting Terminations Location Canada* USA** clearance to the termination frame above grade, veranda, porch, deck, or balcony 12 inches 12 inches clearance to top of doors or operable windows 12 inches 12 inches 9 inches 12 inches...
  • Page 32: Warranty

    The duration of any implied warranty with respect to this Montigo Gas Appliance is limited to the duration of the foregoing warranty. Some states do not allow limitation on how long an implied warranty lasts, so the above may not apply to you.
  • Page 33: State Of Massachusetts

    H*38DF PRC Panorama Indoor Gas Fireplace Appendix Appendix C: State of Massachusetts Amendment (Gas Fireplace / Equipment sold in the State of Massachusetts) 5.08: Modifications to NFPA-54, Chapter 10 (1) Revise NFPA-54 section 10.5.4.2 by adding a second exception as follows: Existing chimneys shall be permitted to have their use continued when a gas conversion burner is installed, and shall be equipped with a manually reset device that will automatically shut off the gas to the burner in the event of a sustained back-draft (2) Revise 10.8.3 by...
  • Page 34 H38DF PRC Panorama Gas Fireplace Ferndale, Washington Langley, British Columbia TF: 1.800.789.6236 TF: 1.800.378.3115 FX: 1.866.3000.0927 FX: 1.604.607.6462 XG0211 - 040912.1...

Table of Contents