GigE FC11000GE Instruction Manual page 27

(27) Command "WMG"
Function: Command for writing MGC gain (Write MGC GAIN)
Transmission from host: STX: "WMG": MGC setting value: MGCB setting (right screen): ETX
Return by camera:
A 2 digit ASCII code from "80" to "7F" in the hexadecimal system (-128 to +127 decimal) is used for the MGCB setting
value.
Example) If level -1 (decimal) is set:
Example) If level 90 (decimal) is set as a MGC setting value, and level -1 (decimal) is set as a MGCB setting value
STX: "WMG": "5A": "FF": ETX
(28) Command "ROF"
Function: Command for reading offset (Read OFFSET)
Transmission from host: STX: "ROF": ETX
Return by camera:
(29) Command "WOF"
Function: Command for writing offset (Write OFFSET)
Transmission from host: STX: "WMG": OFFSET setting value: OFFSETB setting (right screen): ETX
Return by camera:
A 2 digit ASCII code from "20" to "E0" (32 to 224; decimal) in the hexadecimal system is used for the OFFSET setting
value.
Example) If level 100 (decimal) is set:
A 2 digit ASCII code from "80" to "7F" (-128 to +127; decimal) in the hexadecimal system is used for the OFFSETB setting
value.
Example) If level +5 (decimal) is set:
Example) If level 100 (decimal) is set as an OFFSET setting value and level +5 (decimal) is set as an OFFSETB setting
value:
STX: "WOF": "64": "05": ETX
(30) Command "RPS"
Function: Command for reading preset (Read PRESET)
Transmission from host: STX: "RPS": ETX
Return by camera:
When gain & offset set value coincides with preset value (four levels of preset value), corresponding preset No. is
read. When it does not coincide with preset value, "0" is returned.
(31) Command "WPS"
Function: Command for writing preset (Write PRESET)
Transmission from host: STX: "WPS": "PRESET No.": ETX
Return by camera:
It is able to read out and use PRESET (four levels of gain preset value ) set before shipment.
The following commands are used exclusively for FS11000GE.
(32) Command "RCG"
Function: Command for reading color gain (Read COLOR GAIN)
Transmission from host: STX: "RCG": "A" or "B": ETX
Return by camera:
(33) Command "WCG"
Function: Command for writing color gain (Write COLOR GAIN)
Transmission from host: STX: "WCG": "A" or "B": RED setting value: GREEN setting value: BLUE setting value: ETX
Return by camera:
The transmitting command has the following meanings:
STX: "WCG": "A" or "B": RED setting value: GREEN setting value: BLUE setting value: ETX
*1
*1 A: The image on the left side (DUAL scan), Full image (SINGLE scan)
B: The image on the right side (DUAL scan)
*2 GAIN set value for each color (red, green, blue)
STX: ACK: ETX (transaction completion), or STX: NAK: ETX (transaction rejection)
"FF"
STX: ACK: "RMG": OFFSET setting value: OFFSETB setting (right screen): ETX
STX: ACK: ETX (transaction completion), or STX: NAK: ETX (transaction rejection)
"64"
"05"
STX: ACK: "RPS": PRESET No.: ETX
STX: ACK: ETX (transaction completion), or STX: NAK: ETX (transaction rejection)
STX: ACK: "RCG": "A" or "B": RED setting value: GREEN setting value: BLUE setting value: ETX
STX: ACK: ETX (transaction completion), or STX: NAK: ETX(transaction rejection)
*2
- 27 -
K09821;27/37