Table of Contents
Advertisement
Table 6-2 Setting manipulation for Operation Mode Setting [Group 1]
Position of
mode switch
0
Change of gain
1
Menu display
2
Selection of preset 1 or 2
3
Selection of preset 3 or 4
4
All pixels
・
5
Shutter – continuous/asynchronous (S.FORM / front) Continuous(NORMAL) Asynchronous(ASYNC)
6
Shutter – high speed/low speed (S.TIME / rear)
7
Change of shutter speed (S.TIME / front)
8
Digital offset
9
Not used
A to F
Program pages from A to F
(Note) Decibel value in "Selection of preset" is a rough value.
(Note) The shutter speed can be changed only when the shutter switch is currently set at any other positions than "0".
When the shutter switch is positioned at "0", the shutter speed cannot be changed even if the mode switch is set to
the position "7" and the UP/DOWN switch is manipulated. (The shutter is always OFF where shutter switch = "0".)
Table 6-3 Setting manipulation for Operation Mode Setting [Group 2]
Position of
mode switch
1
Menu display
2 to 3
Not used
4
Enabled/disabled for pulse width control (PWC) (!)
A to F
Program pages from A to F
(!)
When the setting of " Enabled/disabled for pulse width control" is not set to be "ENABLED", the pulse width control is
not effective even if the shutter switch is set to the position "9" for the asynchronous shutter operation. In this case, the
preset shutter asynchronous shutter is effective.
Table 6-4 Setting manipulation for Operation Mode Setting [Group 3]
Position of
mode switch
1
Menu display
2
Operation confirmation buzzer
3
Serial communication baud rate
4 to 5
<Not used>
6
Polarity setting for Vinit2
7
Strobe signal output
Table 6-5 Setting manipulation for Operation Mode Setting [Group 4]
Position of
mode switch
1
Menu display
2
Test pattern
3
Output bit
4
Output form
5
Enabled/disabled for automatic correction
6
<Not used>
7
Vsub voltage
[Explanation] Vsub voltage
Vsub voltage is the bias voltage (substrate voltage) that serves to control the blooming effect (resulting in blur or running
image at a saturating area) that arises from excessive light getting into CCD.
If a high Vsub voltage is set, the blooming effect can be reduced, although an excessively high voltage leads to a
narrower operation range of CCD because it is associated with a decrease in the saturating voltage of the CCD output.
It is appropriately set before shipment because the optimum Vsub voltage varies by CCD.
*
Notes in common with all setting groups
(Note) The standard factory mode (default) is underlined.
(Note) The default value of output bit is 8 bit. It is changed to 10 bit at first UP operation and 12 bit at second UP operation.
(Note) The default value of strobe signal output is OFF. It is changed to exposure timing signal at first UP operation and
busy signal at second UP operation.
(Note) The items marked with <* C> in the table (configuration items) are automatically stored in EEPROM whenever they
are changed.
(Note) The new settings of the other items than the configuration items are lost at the time of power-off unless they are
manually saved in the program pages after changing them.
Item to be changed
(MENU)
Double speed scanning mode(SCAN / front) All pixels (NORMAL)
(OFFSET)
Item to be changed
(MENU)
(-)
Item to be changed
Item to be changed
Increase in gain
<* C>
ON
Preset 2 (+19db)
Preset 4 (+25db)
High speed (HIGH)
Shorter
Increase in offset
Write
<* C>
ON
ENABLED
Write
(MENU) <* C>
ON
(BZ)
<* C>
ON
(BAUDP) <* C>
19200 bps
(-)
-
(Vinit2)
<* C>
Positive logic
(POSITIVE)
(STRB0,1) <* C>
Switching
(MENU) <* C>
ON
(PATTERN) <* C> ON
(BIT)
<* C>
Increase in bit
(FORM) <* C>
DUAL
ENABLED
(ATCR) <* C>
(-)
-
(VSUB)
<* C>
Increase in voltage
- 15 -
UP/DOWN switch
UP position
DOWN position
Decrease in gain
OFF
Preset 1 (+16db)
Preset 3 (+22db)
Double speed (DOUBLE)
Low speed (LOW)
Longer
Decrease in offset
Readout
UP/DOWN switch
UP position
DOWN position
OFF
DISABLED
Readout
UP/DOWN switch
UP position
DOWN position
OFF
OFF
9600 bps
-
Negative logic
(NEGATIVE)
Switching
UP/DOWN switch
UP position
DOWN position
OFF
OFF
Decrease in bit
SINGLE
DISABLED
-
Decrease in voltage
K09821;15/37
Advertisement
Table of Contents
