Table of Contents
Advertisement
● In the case where the exposure time is set by the shutter SW number on the connector panel:
Example) If the shutter SW is set to "4":
STX: "S": ".": ".": ".": "S4..": ETX
● In the case where the exposure time is set to 3Hs in the asynchronous/high speed shutter mode:
STX: "S": "A": "H": ".": "0003": ETX
● In the case where the control is returned to the setting by the shutter switch on the rear panel.:
STX: "S": ".": ".": ".": "0000": ETX
(Note)
In the case where the exposure time is externally set using S command, the exposure time is locked finally to the
position designated by S command or directly designated value. The locked state is released by setting the
exposure time to "0000" using RS-232C as described above. To release the locked state without the use of
RS-232C after setting the exposure time by RS232C, execute "Read-out of Factory Default" operation
(Note) The allowable range of number is as follows when in directly setting the exposure time. The operation out of
the range is not guaranteed.
Normal scan
Double speed scan: H'0000 to H'0551 (D' 0 to 1361) (where "0" is used only when cancelling the external time setting )
(9) Command "E"
Function: Command for editing shutter menu
Transmission from host: STX: "E": "H" : SW0: SW1: SW2: SW3: SW4: SW5: SW6: SW7: SW8: SW9: ETX
Return by camera:
The exposure time (H) to be allocated to the shutter SW number is expressed in 4 digits in the hexadecimal system for
※
SW0 to SW9.
The exposure time for SW0 can not be changed.
※
Example) If only the exposure time of SW5 for the high speed shutter operation is changed to 88 (decimal):
STX: "E": "H": ".": ".": ".": ".": "."
: "0058": ".": ".": ".": ".": ETX
(10) Command "W"
Function: Command for saving operation mode (Write into page memory)
Transmission from host: STX: "W": memory page ("A" to "F"): ETX
Return by camera:
The current setting can be written and saved in the EEPROM of the specified page number.
(11)
Command "L"
Function: Command for reading out operation mode (Load)
Transmission from host: STX: "L": reading page ("A" to "H"): ETX
Return by camera :
*
The factory default is stored in the Page H, which will be used when restoring to the default setting.
(12)
Command "WMC"
Function: Command for writing in configuration flag register (CR) (Write Mode Configuration)
Transmission from host: STX: "WMC": flag set value: ETX
Return by camera:
The content of "flag set value" (2 bytes/4 characters) can be written in the configuration register.
(Note) This command does not execute the writing in EEPROM, and the setting by this command is lost when the power
is turned off. To save the setting value in EEPROM, use another command, "SMC".
(13) Command "WMF"
Function: Command for writing in mode flag register (FR) (Write Mode Flag)
Transmission from host: STX: "WMF": flag set value: ETX
Return by camera :
The content of "flag set value" (2 bytes/4 characters) can be written in the flag register.
(Note) This command does not execute the writing in EEPROM, and the setting by this command is lost when the power
is turned off. To save the set value in EEPROM, use other commands, "WA to WF", to save in the specified pages.
(14) Command "RMC"
Function: Command for reading configuration flag register (CR) (Read Mode Configuration)
Transmission from host: STX: "RMC": ETX
Return by camera:
: H'0000 to H'087B (D' 0 to 2171) (where "0" is used only when cancelling the external time setting )
STX: ACK: ETX (transaction completion), or STX: NAK: ETX (transaction rejection)
STX: ACK: ETX (transaction completion), or STX: NAK: ETX (transaction rejection)
STX: ACK: ETX (transaction completion), or STX: NAK: ETX (transaction rejection)
STX: ACK: ETX (transaction completion), or STX: NAK: ETX (transaction rejection)
STX: ACK: ETX (transaction completion) or STX: NAK: ETX (transaction rejection)
STX: ACK: "RMC": flag set value: ETX (transaction completion), or STX: NAK: ETX (transaction
rejection)
- 24 -
K09821;24/37
Advertisement
Table of Contents
