Table of Contents
Advertisement
(Note) When the pulse width control mode is set for the asynchronous shutter operation or when a shutter setting value is
out of the predetermined range in the partial scan or other operation, the actual time is displayed as "--.-".
S.FORM:
The current shutter system is displayed. The left is either continuous (NORMAL) or asynchronous
(ASYNC), and the right is either high speed (HIGH) or low speed (LOW).
SCAN:
The current scanning system is displayed. It is either all pixel readout scan (NORMAL) or partial scan
(PARTIAL). ( → See "Priority relationship among scan mode setting items" described in another section)
MENU2
●
GAIN B:
The gain correction value for the image on the right side is set.
OFFSET B:
The offset correction value for the image on the right side is set.
PWC:
Whether the pulse width operation mode is ENABLED or
DISABLED in the asynchronous shutter mode when the
shutter switch is positioned at "9" , is selected.
MENU3
●
BZ:
This is to switch between (ON) and (OFF) for the confirmation
sound to be activated when switch manipulation is made.
BAUD:
The baud rate used for RS-232C communication is displayed.
Vinit2:
The polarity of the trigger signal via CC1 of Camera Link is set.
The factory default is negative logic (NORMAL). When
(INVERTED) is selected, positive logic input is used.
STRB:
The signal (OFF/Exposure timing signal/Busy signal) of STRB
output terminal is set.
MENU4
●
PATTERN:
This is to switch between (ON) and (OFF) for the test pattern
output.
bit:
This is to switch between (8bits),(10bits) and (12bits) for the bit
number of the image output.
FORM.:
This is to switch between (DUAL) and (SINGLE) for the CCD
output form.
ALC(Automatic Level Correction):
This is to switch between (ON) and (OFF) for the Automatic
correction function.
VSUB:
The setting value of Vsub voltage (substrate voltage of CCD
element) is displayed.
Since the value is optimally set before shipment, the user is
not required to change it as a general rule.
*
The following items are for display only; they cannot be directly changed
on the menu. These are automatically updated when a corresponding
change is made using the switches:
MS=
The current position of the mode switch is displayed.
SS=
The current position of the shutter setting switch (EXP.) is
displayed.
MF=
The information (16 bits x 2 sets) of the internal mode flags
of the camera (internal flags to determine operation) is displayed in
the hexadecimal system. The details of the internal flags are
described later.
Tc=
The current internal temperature of the camera is displayed in
Celsius. The temperature data are refreshed every 0.4 seconds.
[ID information display]
The ID code and other information set by the user for each camera can be saved in the camera (via serial communication).
The settable maximum number of characters are 15, and alphabets (both upper and lower cases), numbers and some
special symbols such as"+" and "-" excluding the control codes are used.
( → Refer to the section of "Serial Communication Control" for the details.)
The ID code set by the user is displayed on the lower left of the "Menu Display of Setting Group 1" by the OSD function;
this allows the user to confirm the setting content (ID: onward).
(If the ID code is not set, the camera type is displayed instead.)
The right figure shows an example where "CAMERA-1" is set as the ID information.
- 18 -
K09821;18/37
MENU2
MENU
: ON
GAINB
:
+1
OFFSTB :
-4
PWC
: DISABLED
MS=A SS=7
MF=0008.0000
Camera type
Menu display of Se tting Gr oup 2
MENU 3
MENU
: ON
BZ
: ON
BAUD
: 9600bps
-
: (Reserved)
: (Reserved)
Vinit 2
: NORMAL
STRB
: OFF
MS=CSS=7
MF=0008.0000
Camera type
Menu disp la y of Setting Group 3
MENU 4
MENU
: ON
PATTERN : OFF
bit
: 10bit
FORM.
: DUAL
ALC
: ON
VSUB
: 115=H'73
MS=C SS=7
MF=0008.0000
Camera type
Menu disp la y of Setting Group 4
MS=1 SS=7
MS=1 SS=7
Camera type
ID: CAMERA-1
ID not specified
ID speci fied
[V.X.XX]
[V.X.XX]
[V.X.XX]
Advertisement
Table of Contents
