Table of Contents
Advertisement
6. How to Change Settings
(6-1) How to set shutter speed
The shutter speed is determined mainly by the setting positions of the shutter switch from "0" to "9".
Table 6-1 Setting value of shutter speed
Position
of
High speed shutter (continuous/asynchronous)
shutter switch
DUAL output
0
1/
5 second
1
1/ 2000 second
2
1/ 1000 second
3
1/ 500 second
4
1/ 250 second
5
1/ 120 second
6
1/
60 second
7
1/
30 second
8
1/
15 second
1/ 7.5 second
9
Pulse width control /asynchronous (!)
(Note) (H) and (V) in the table represent the horizontal time unit and the vertical time (frame duration) unit respectively.
(Note) The values in the table are the shutter speed in all pixels scanning, they get longer in 2 lines binning scanning.
Confirm it in OSD(On screen display) for details.
(Note) "No shutter" in the table means the continuous shutter mode with exposure time = 1 frame duration.
(Note) The value of the each shutter speed is the factory default value. The shutter speed of each position (excluding
shutter position = 0) is possible to change by the user in the operation mode [Group 1].
(!) As for this camera, "Pulse width control time/asynchronous" must be set to be "Pulse width control (PWC) =
ENABLED". When it is set to be "Pulse width control (PWC) = DISABLED" (default), the selection can be made out of
the 9 levels not only for the continuous shutter operation but also for the asynchronous shutter operation.
(6-2) How to set operation mode
The setting items of the operation modes are divided into 4 groups of Group 1, Group 2, Group 3 and Group 4 as follows:
Group 1 ············ Group1 is mainly used for setting the basic operation (Shutter speed, Gain etc.). After start-up, set the
mode switch to the position corresponding to the item to be changed and then manipulate the
UP/DOWN switch to change the setting.
Group 2 ············ Group2 is mainly used for setting
After start-up, set the mode switch to the position corresponding to the item to be changed and then
manipulate the UP/DOWN switch to change the setting.
Group 3 and 4 ···· These are mainly used for setting the configuration items (Terminology below).
After start-up, set the mode switch to the position corresponding to the item to be changed and then
manipulate the UP/DOWN switch to change the setting.
(Note) When any setting item is changed, it must be saved in one of the program pages from "A" to "F" before turning off
the power to store the data in the memory of the camera. Carefully note that the new setting is not automatically
saved and that the prior setting will be effective at the next time of power-on if the power is turned off before storing
it. The configuration items, however, are automatically saved whenever they are changed.
[Terminology] Configuration items ···· They are the common setting items that are independent of the program pages.
M enu 1
L ED
Fig. 6-1 Operation mode flow diagram
SINGLE output
1/ 2.7 second
1/ 1200 second (
1/ 530 second ( 13H)
1/ 260 second ( 28H)
1/ 130 second ( 56H)
1/
60 second ( 117H)
1/
32 second ( 237H)
1/
16 second ( 475H)
1/
8 second ( 952H)
1/
4 second (1906H)
These items are automatically saved in the internal EEPROM at the same time as
they are changed by manipulating the switches on the rear panel.
＝
＝
G roup 1
：
D is pla y O F F
：
Fla s hing in gre e n
： 「 １」
M ode sw itc h
Ｕ Ｐ
ＤＯ ＷＮ
：Ｄ Ｏ ＷＮ
/
sw itc h
Me nu
hidde n
Low speed shutter (continuous)
DUAL output
No shutter (continuous)
1/ 5 second
5H)
1/ 2.6 second
1/ 1.7 second
1/ 1.3 second
1/ 1.0 second
1/ 0.86 second
1/ 0.74 second
1/ 0.65 second
1/ 0.57 second
1/ 0.52 second
the auxiliary function (Gain correction etc.)
＝
＝
G roup 1
：
Me nu 1
D ispla y ON
：
LED
Fl ash ing in g reen
M ode sw itch
U P /DOW N sw itc h
＝
＝
Gr oup 2
：
Me nu 2
D is pla y O N
：
LED
Fl ash in g in g reen
(q u i c k )
M ode sw itch
U P /DOW N sw itc h
＝
＝
G roup C
：
M enu 3
D ispla y ON
：
LED
F la shing in ora nge
M ode sw itch
U P /DOW N sw itc h
＝
＝
G r oup D
：
M e nu 4
D ispla y ON
： Flashing in orange(quick)
LED
M ode sw itch
U P /DOW N sw itc h
＝
Fac tory de fa ult
：
LED
Fl ash ing in red
M ode sw itc h
- 14 -
U P /DOW N sw itch
SINGLE output
1/ 2.7 second
1/ 1.35 second ( 2V)
1/ 0.90 second ( 3V)
1/ 0.68 second ( 4V)
1/ 0.54 second ( 5V)
1/ 0.45 second ( 6V)
1/ 0.39 second ( 7V)
1/ 0.34 second ( 8V)
1/ 0.30 second ( 9V)
1/ 0.27 second ( 10V)
：「 １」
：Ｕ Ｐ
： 「１ 」
：Ｕ Ｐ
： 「１ 」
：Ｕ Ｐ
：「 １」
：Ｕ Ｐ
：「 １ 」
：ＵＰ
K09821;14/37
Advertisement
Table of Contents
