Table of Contents
Advertisement
Section 2
EXPANDED VIEW OF MIG TORCH
3
2
1
1 7
NO.
PARTS
1
Diffuser D.12 14-15AK
2
Contact Tip 0.8/M6*25
IFT0063
14
3
15AK Goose gun neck assy.
IHJ0645
13
IHJ0028
12
4
Adapter for goose neck
ICN0663
11
5
Plastic adapter
IHJ0782
10
IHJ0715
9
6
MIG gun handle
IFT0874
8
IHQ0070
7
7
Torch switch 21.8mm
ICV0685
6
8
Screw D.3*10
IHJ0030
5
IZH0667
4
9
Handle locking ring
ICZ0087
3.1
10
Articulating joint 15AK
ICZ6087
3
ICU0003-08
2
11
Coaxial cable assy /16mmq/3m
1
ICS0063
序号
图
号
12
Cable thimble 12-16-25 MMQ
13
CO
Euro-rear connector handle
2
14
Retaining Screw M4*6 UNI 6107
15
Knurled locking nut
16
Euro-main connector
17
Securing nut for gas input
18
Insulating feed pipe 0.6-0.8 3m, Blue
19
Contact Tip Wrench
NOTE: Over time, pressure on the drive rolls causes metal fragments from the filler wire's surface to find its way
to the gun cable liner. If the wire guide is not cleaned, it can gradually clog up and causes wire feed malfunctions.
If feeding difficulty is observed, clean the liner in the following manner：
1) Remove the welding gun's gas nozzle, contact tip and contact tip's adapter.
2) With an air nozzle below compressed air through the wire guide. Wear eye protection!
3) Blow the wire feed mechanism and reel housing out with dry compressed air.
4) Reassemble components. Tighten the contact tip and contact tip's adapter to spanner tightness.
The liner may eventually become worn and will need to be replaced. When welding aluminum, a Teflon or special
liner must be used, necessitating a liner change. To change the liner:
1) Remove the securing nut of the liner (#17) which exposes the end of the wire guide.
2) Straighten the gun cable and withdraw the liner from the gun.
3) Carefully push a new wire guide in to the gun. Make sure that the wire guide travels all the way to the contact tip.
4) Make sure the O-ring at the machine-end of the gun is installed
5) Tighten the wire guide in place.
6) Cut the liner 2mm from the mounting nut and file the sharp edge of the liner.
7) Reattach the gun and tighten all parts.
8) Re-thread wire.
Setup Guide and component Identification
4
5
6
3.1
8
7
1 9
1 6
1 5
1 3
QTY
1 4
1
1
1
螺丝 M4X6 UNI 6107
1
1
二氧化碳欧式后把套
1
电缆护套 12-16-25 MMQ
1
1
同轴电缆组/16mmq/3米
1
1
电缆支撑用球节 15AK
1
手柄锁紧环
1
3
螺丝 D.3x10
1
1
焊枪用开关 21.8mm
1
MIG蓝色手柄
3
1
塑料适配器
1
六角适配器
1
1
15AK 枪颈
1
1
15AK 枪颈(包括六角适配器和塑料适配器)
1
导电嘴 0.8/M6*25
1
1
喷嘴 D.12 14-15AK
描
述
数量
1
1
1
1
1
1
1
1
9
10
1 8
1 2
NOTE: Some components may appear slightly different as
design/supplier changes are made from time to time. At time of
ICG6000
19
IIC0500
18
publication, the standard torch provided with MTS 160/200S is
IZT0071
17
the Trafimet Ergoplus 15, which interchanges consumables with
16
ITB0059
IHJ0063
15
the Binzel MB15ak torch used elsewhere in the Everlast I-MIG
序号
图
号
line. The widely used Euro-connecter on the MTS series MIG
torches allows the customer to select and install about any
更改文件号
签字
标记
处数
brand after-market torch desired.
设计
标准化
制图
工艺
校对
批准
审合
日期
备
注
TO INSTALL MIG GUN/TORCH:
A.
Align pins on #16 with the feeder receptacle.
B.
Fully engage the connector into the receptacle.
C.
Twist knurled nut (#15) on connector until the nut is snug.
DO NOT OVERTIGHTEN! USE HAND PRESSURE ONLY.
21
11
1
导电嘴扳手
1
带绝缘层送丝管0.6-0.8 3米 蓝色
1
送丝管锁紧螺母
1
欧式中央插头/弹性针
1
焊枪锁紧螺母/塑料螺纹
描
述
数量
ICT2098
日期
零部件描述
参考编号
焊枪15/3米/弹性针/蓝色手柄
上海亿诺科技有限公司
备
注
公差选择范围
材料
重量(g)
外形尺寸
-------
共
页
共
页
上海市顾戴路2535弄99号3号楼2楼
Advertisement
Table of Contents
