8Topping Your Dryer; Pausing Or Restarting; Control Locked; Loading - Kenmore Elite HE4 110.8508 Series Use & Care Manual
Electric
Hide thumbs
Also See for Elite HE4 110.8508 Series:
- Use and care manual (57 pages) ,
- Use and care manual (56 pages) ,
- Use and care manual (60 pages)
Table of Contents
Advertisement
To use a Manual Cycle
•
Select a Manual Cycle.
•
Press MORE TIME or LESS TIME until the desired drying
!me is displayed. Tap MORE TIME or LESS TIME and the
time will change by 1-minute intervals. Press and hold
MORE TIME or LESS TIME and the time will change by
5--minute intervals.
NOTE: The More TIme and Less TIme features can be
used only wrth Manual Cycles.
OMOll!TI~E
OUSSTIME
•
Press TEMPERATURE until the desired temperature
glows.
NOTE: During a Manual Cycle, you can change the settings
for TIme. Temperature. WRINKLE GUARD" and End of Cycle
Signal. Press PAUSE/CANCEL twice to stop the dryer and
clear the settings. Selec1 another cycle or option.
(OPTIONAL STEP) If desired, select OPTIONS. For more
details, see "Options."
(OPTIONAL STEP) If desired, set the END of CYCLE SIGNAL.
Select HIGH or LOW to alert you when a cycle ends.
Press and hold START for approximately
3 seconds until
dryer starts. Be sure the door is closed.
•
If you do not press Start wrthin 5 minutes of selecting the
cycle, the dryer automatically
shuts off.
•
If you wish to end your drying cycle after pressing Start,
press PAUSE/CANCEL twice.
Stopping Your Dryer
stop your dryer at any lime
I
'ess PAUSE/CANCEL twice or open the door.
Pausing or Restarting
pause the dryer at any lime
I
pen the door or press PAUSE/CANCEL once.
restart the dryer
I
ose the door. Press and hold START until dryer starts.
DTE: Drying will continue from where the cycle was interrupted
~ou close the door and press Start within 5 minutes. If the cycle
interrupted for more than 5 minutes. the dryer will shut off.
llect new cycle settings before restarting the dryer.
Control Locked
,is feature allows you to lock your settings to prevent
,intended use of the dryer. You can also use Ihe Control Locked
ature to prevent unintended cycle or option changes during
yer operation.
, enable the Control
Locked feature:
ess and hold AUTO DRY LEVEL for 3 seconds. Control Locked
)ws and a single beep tone is heard. To unlock, press and hold
JTO DRY LEVEL for 3 seconds. The indicator light turns off.
Loading
Property loading your dryer can lower your utility bill and prolong
the life of your gannents.
Loading suggestions
•
Load the dryer by the amount of space items take up. not by
their weight.
'
•
Do not overload the dryer. This causes uneven drying and
wrinkling.
Super Capacity Dryers
Heavy Wor!< Clothes
4 jeans
2 sweatpants
4 workpants
2 sweatshirts
4 workshirts
Towels
10 bath towels
14 washcloths
10 hand towels
Mixed Load
3 sheets (1 king, 2 twin)
9 T-shirts
4 pillowcases
9 shorts
3 shirts
10 handkerchiefs
3 blouses
Drying and Cycle Tips
Select the correct cycle and dryness level or temperature for your
load. If an Auto Dry Cycle is running. the display shows the
your
estimated cycle time when
dryer is automatically
sensing
the dryness level of your load. If a Manual Cycle is running, the
display shows the exact number of minutes remaining in the
cycle.
.
Coel Down tumbles the load without heat during the last few
minutes of all cycles. Coel Down makes the loads easier to
handle and reduces wrinkling. The length of the Cool Down
depends on the load size and dryness level.
Drying lips
•
Follow care label directions when they are available.
add
•
If desired,
a fabric softener sheet. Follow package
instructions.
I
I
•
To reduce wrinkling, remove the load from the dryer as soon
as tumbling stops. This is especially important for pennanent
press, knits. and synthetic fabrics.
•
Avoid drying heavy work clothes together wrth lighter fabrics.
This could cause overdrying of lighter fabrics and lead to
increased shrinkage or wrinkling.
Cycle lips
•
Dry most loads using the preset cycle settings.
•
Refer to the Auto Dry chart or Manual Preset Cycle Settings
chart (in the 'Cycles" section) for a guide 10 drying various
loads.
•
Drying temperature and Auto Dry Level are preset when
you choose an Auto Dry Cycle. You can select a different
dryness level, depending on your load, by pressing Auto
Dry Level and choosing More or Less.
Cycle,
•
If you wish to adjust the cycle length of a Manual
press More Time or Less TIme. Adjust the temperature of
a Manual Cycle by pressing Temperature until the desired
temperature is selected.
NOTE: You cannot choose an Auto Dry Level with Manual
Cycles.
- Quick Links:
- Tools and Parts
- Troubleshooting
Hide quick links:
Advertisement
Table of Contents
