Blastrac BG-250E Operating Manual
Hide thumbs Also See for BG-250E:

Advertisement

OPERATING MANUAL BG-250E & BG-250P
VERSION 2.0

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BG-250E and is the answer not in the manual?

Questions and answers

Summary of Contents for Blastrac BG-250E

  • Page 1 OPERATING MANUAL BG-250E & BG-250P VERSION 2.0...
  • Page 2: Ec Declaration Of Conformity

    Conforms with the Health and Safety requirements of the European Directive of the machine Safety. In case of changes to the machine without our written authorization this declaration loses its validity. Model: BLASTRAC BG-250E Serial number: xxxxB BLASTRAC BG-250P Serial number: xxxxB 1.
  • Page 3: Table Of Contents

    4. Initial operation Checkpoints of electrical safety Checkpoints of machine safety Removing the diamond disc Mounting the diamond disc 5. Operating Switch on the BG-250E Switch off the BG-250E Switch on the BG-250P Switch off the BG-250P Operating during grinding 6. Maintenance Replacing the flexible coupling 7.
  • Page 4: Introduction

    The machine has a rotating adapter plate where the diamond disc can be fixed on The rotating parts are covered by a protection cap with a connection for a dust hose. With a suitable Blastrac dust collector you can work without causing dust. Application The BG-250 can be used on almost any floor to plane, to remove coatings or glue residues or to make ready for coatings.
  • Page 5: Safety

    3. Safety Before operating the machine, the personnel must be familiar with the safety instructions given in this manual. Keep this manual near to the machine, so it can always be consulted. Safety precautions The surface to be treated must be swept clean to remove stones, screws etc. ...
  • Page 6: Safety Instructions

    Safety instructions Do not stand the machine on the diamond disc or coupling when it is not in use, this will cause  deformation to the flexible coupling. Put the machine always on the machine support which is made for this reason.
  • Page 7: Initial Operation

    4. Initial operations Before using the machine it is committed to inspect the machine. It is not permitted to use the machine if the machine safety is not according the checkpoints below. Checkpoints for electrical safety Use only extension cables for extending the main cable that are sized and marked in accordance with ...
  • Page 8: Operating

    5. Operating During operating the BG-250, the following additional safety instructions must be followed closely. Switch on the BG-250E Turn on the dust collector before switching on the machine.  Connect the dust hose with the machine  Stand behind the machine ...
  • Page 9: Switch Off The Bg-250P

    Switch off the BG-250P Push the gas throttle (4) to the front.  Push the red button (6)  Wait until the machine stops rotating before you set the machine on the support with the lever handle  Pull out the power supply and the key of the deadman switch (2) ...
  • Page 10: Maintenance

    Protect the electrical motor from moisture, heat, dust and shocks. All repair work must to be done by qualified Blastrac personnel, this to guarantee a safe and reliable machine. Any guarantee on the machine is expired when: Non original Blastrac parts and diamond discs have been used ...
  • Page 11: Technical Data

    Dust hose connection 75 mm Ø 75 mm Ø 75 mm Ø 75 mm Ø Contact Blastrac BV Suitable filter unit We will assist you with a good advice Design and specifications are subject to change without notice by Blastrac BV...
  • Page 12: Info@Blastrac.com.es

    Headquarter Blastrac Poland Blastrac Italy Blastrac The Netherlands Golina, Dworcowa 47a S.S. 10 Padana Inferiore, 41 Utrechthaven 12 PL – 63-200 Jarocin IT – 29012 Caorso (PC) NL – 3433 PN Nieuwegein Tel – 0048 627 40 41 50 Tel – 0039 0523 81 42 41 Tel –...

This manual is also suitable for:

Bg-250p

Table of Contents