Blastrac BGS-250 Operating Manual
Hide thumbs Also See for BGS-250:

Advertisement

Quick Links

Operating manual BGS-250
BGS-250
Version 1.1
info@blastrac.eu

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BGS-250 and is the answer not in the manual?

Questions and answers

Summary of Contents for Blastrac BGS-250

  • Page 1 Operating manual BGS-250 BGS-250 Version 1.1 info@blastrac.eu...
  • Page 2: Ec Declaration Of Conformity

    Operating manual BGS-250 2/11 EC DECLARATION OF CONFORMITY in accordance with Appendix II sub A of Directive 98/37/EC BLASTRAC B.V. Utrechthaven 12 NL - 3433 PN NIEUWEGEIN Tel: 0031 (0)30 601 88 66 Fax: 0031 (0)30 601 83 33 Info@Blastrac.nl...
  • Page 3: Table Of Contents

    Operating manual BGS-250 3/11 Table of contents EC Declaration of Conformity 1. Introduction 2. Machinedescription Application Accessory’s 3. Safety Safety precautions Safety regulations Safety instructions 4. Initial operation Checkpoints of electrical safety Checkpoints of machine safety Removing the diamond disc Mounting the diamond disc 5.
  • Page 4: Introduction

    With a suitable Blastrac dust collector you can work without causing dust. The machine can be leveled by turning the height adjustment handle. Application The BGS-250 can be used on almost any floor to plane, to make ready for coatings, or to remove coatings or glue residues. Height adjustment...
  • Page 5: Safety

    Operating manual BGS-250 5/11 3. Safety Before operating the machine, the personnel must be familiar with the safety instructions given in this manual. Keep this manual near to the machine, so it can always be consulted. Safety precautions The surface to be treated must be swept clean to remove stones, screws etc.
  • Page 6: Safety Instructions

    Pull out the main plug when changing the disc or flexible coupling. ▪ The BGS-250 weights 70 kilogram. It is not allowed to lift this machine with 2 ▪ persons. Use preferably appropriate appliances as a lift or crane.
  • Page 7: Initial Operation

    Operating manual BGS-250 7/11 4. Initial operation Before using the machine it is committed to inspect the machine. It is not permitted to use the machine if the machine safety is not according the checkpoints below. Checkpoints of electrical safety Use only extension cables for extending the main cable that are sized and marked ▪...
  • Page 8: Operating

    Operating manual BGS-250 8/11 5. Operating During operating the BGS-250, the following additional safety instructions must be followed closely. Switch on the machine Level the machine with the height adjustment handle ▪ Turn on the dust collector before switching on the ▪...
  • Page 9: Maintenance

    Store the cleaned and dry machine in a dry and humid free room. Protect the electrical motor from moisture, heat, dust and shocks. All repair work must to be done by qualified Blastrac personnel, this to guarantee a safe and reliable machine.
  • Page 10: Technical Data

    Contact Blastrac BV unit We will assist you We will assist you We will assist you with a good advice with a good advice with a good advice Design and specifications are subject to change without notice by Blastrac BV info@blastrac.eu...
  • Page 11 Operating manual BGS-250 11/11 HEADQUARTER Blastrac BV The Netherlands Utrechthaven 12 NL - 3433 PN Nieuwegein Tel: 0031 (0)30 601 88 66 Fax: 0031 (0)30 601 83 33 info@blastrac.nl Blastrac United Kingdom Unit 2, Outgang Lane, Dinnington Sheffield, South Yorkshire GB –...

This manual is also suitable for:

Bgs-250/0000Bgs-250/0003Bgs-250/0004Bgs-250/2002

Table of Contents