Subscribe to Our Youtube Channel
Related Manuals for Kirisun PT6700
Summary of Contents for Kirisun PT6700
-
Page 1: Instruction Manual
INSTRUCTION MANUAL PT6700 FM TRANSCEIVER Kirisun Communications Co.,Ltd. http://en.kirisun.com... - Page 2 NOTE： INSTRUCTION MANUAL PT6700 FM TRANSCEIVER We are very grateful for your purchasing brand two-way radios produced by Kirisun Communica- tions Co.,Ltd. We believe two-way radio, which always incorporates the latest technology, can bring great convenience to your life and work.
- Page 3 Kirisun or its authorized parities. Due to the update or modification of the product, Kirisun owns the right to change the specifications of software and hardware described in this manual without further notice.
- Page 4 To realize the best performance of the battery, change the Make sure the antenna is correctly installed when using. The battery once a year. radio without antenna may cause damage in the process of transmission. Kirisun Communications Co.,Ltd.
-
Page 5: Table Of Contents
Unpacking and Checking CONTENT Unpack the radio carefully. We recommend that you check the Unpacking and Checking radio and the supplied accessories listed in the following table Preparation before discarding the packing material. If any damage or loss has occurred during shipment, please contact the dealer without delay. Charging the Battery Supplied Accessories Installing/Removing the Battery... -
Page 6: Preparation
Charging the Battery initial use, please charge the new battery. * KB-78B Li-poly battery of Kirisun is applicable to this radio. Plug the adapter into an applicable AC * When charging the battery for the first time after purchase or long-... -
Page 7: Installing The Antenna
I n s t a l l i n g t h e B e l t C l i p Removing the battery Match the two holes of the belt clip Press down the battery latch, and with those on the rear of the radio, push the battery pack downwards until and then fix the belt clip to the radio it separates from the radio. -
Page 8: Basic Operation
Basic Operation LED Indicator Lights up red while transmitting; lights up green while receiving; flashes red when the radio is in low voltage. Switch On Switch on the radio by turning the On/Off/ Volume On/Off/Volume Control Knob control knob clockwise until a click is heard. If Turn clockwise until you hear a click to turn the radio power on. -
Page 9: Functions Of Programmable Buttons
Emergency Press the preprogrammed “Emergency Alarm Receive a Call Off” button to quit the Emergency Alarm Mode. Alarm Off Release the PTT button to receive a call. Press the preprogrammed “Scan” button to Scan Your dealer can set QT/DQT signaling on your radio channels start/stop scanning. -
Page 10: Auxiliary Functions
Auxiliary Functions Battery Saving The dealer can set the power saving mode by programming. TOT (Time-Out-Timer) If this function is enabled, and the radio hasn’t receive any signal or 1) TOT Function no operation is being acted for 10 seconds, the radio will enter a) The time-out-timer can prevent the user from continuously talking Battery Saving Mode. - Page 11 you to ignore (not hear) calls from other irrelevant parties who are on which a signal is detected until that signal disappears. If interval using the same channel. When you receive a signal that has a tone between signal disappearing and continuing scanning has been different from the one set on your radio, you will not hear the signal.
- Page 12 the scan list when pressing the PTT button. Lone Worker Priority Channel + Currently Working Channel: When pressing If lone worker function is enabled by PC software, you can press the the PTT button during scanning, the radio will always transmit from button set as lone worker to start lone working.
-
Page 13: Wired Clone Mode
Troubleshooting Wired Clone Mode If the wired clone function is enabled by PC software, after entering the Wired Clone Mode, the radio needs to be restart to return to user Problem Causes and Solutions mode. The radio A. The battery and the radio are not reliably The operating steps go as follows: cannot be connected. -
Page 14: Specifications
Specifications General Specification PT6700 Problem Causes and Solutions Frequency 136~174MHz, No signal A. The antenna is in poor contact. Please fasten the antenna head. 400~470MHz, B. The HF amplifier is broken, please change it. Number of channels C. The squelch level is so high that the squelch Channel spacing 25kHz(W) /12.5kHz(N) -
Page 15: Fcc Notice
ALWAYS keep the antenna at least 2.5 cm (1 inch) away from the American National Standards Institute (C95.1-1992), IEEE Standard body when transmitting and only use the KIRISUN belt-clip which is for Safety Levels with Respect to Human Exposure to Radio listed in instructions when attaching the radio to your belt, etc., to... - Page 16 Electromagnetic Interference/Compatibility During transmissions, OPERATING NOTES your KIRISUN radio generates RF energy that can possibly cause When transmitting with a portable radio, hold the radio in a vertical interference with other devices or systems. To avoid such position with its microphone 5 to 10 cm (2 to 4 inches) away from interference, turn off the radio in areas where signs are posted to do your mouth.
- Page 17 Exposing the inside of the transceiver to water will result in serious damage to the transceiver. FCC CAUTION: Changes or modifications to this device, not expressly approved by KIRISUN, could void your authority to operate this transceiver under FCC regulations.
Need help?
Do you have a question about the PT6700 and is the answer not in the manual?
Questions and answers