Related Manuals for Jet 505710
Summary of Contents for Jet 505710
- Page 1 Orbital (Jitterbug) Sander #505710, JAT-710 Operation & Parts Manual M-505710 Edition 1 02/2015 427 New Sanford Road LaVergne, TN 37086 Ph.: 800-274-6848 www.jettools.com Copyright © 2015 JET...
-
Page 2: Warranty And Service
Accessories; Shop Tools; Warehouse & Dock products; Hand Tools NOTE: JET is a division of JPW Industries, Inc. References in this document to JET also apply to JPW Industries, Inc., or any of its successors in interest to the JET brand. -
Page 3: Safety Warnings
10. The air tool must be properly lubricated before operating. Do not use this tool for other than its intended use. If used for other purposes, JET disclaims 11. Never start a percussion type air tool (chipper, any real or implied warranty and holds itself breaker, buster, etc.) without securing the... - Page 4 33. Do not lubricate the tool with combustible or storing tool. liquids, such as kerosene, diesel or jet fuel. 23. Make sure tool is switched off, and your finger 34. Do not dispose of this tool with normal off the trigger, before connecting to air supply.
-
Page 5: About This Manual
As with any tool operation, safety of operator and bystanders should be first priority. If there are questions or comments, please contact your local supplier or JET. JET can also be reached at our web site: www.jettools.com. -
Page 6: Tool Specifications
Specifications were current at time of publication, but because of our policy of continuous improvement, JET reserves the right to change specifications at any time and without prior notice, without incurring obligations. -
Page 7: Setup And Assembly
Any missing parts or damage should be reported Place sander on workpiece, and press down ® immediately to your JET distributor. Do not use a on operating lever with palm while grasping damaged tool. Read this instruction manual sander with your fingers. - Page 8 Contaminated air such as a dirty air system or water in the system. Use a light oil containing rust inhibitors, such as SAE #10. Many JET air tools have integral oil • Using wrong size tool for the job. reservoirs, which should be kept filled when in-line •...
- Page 9 Figure 2 Recommended arrangement of air piping and air line system ...
- Page 10 Troubleshooting JAT-710 Orbital (Jittebug) Sander Any disassembly of the tool should be done by qualified service personnel. For problems not addressed below, contact JET technical service at 800-274-6846. Problem Possible cause Remedy Tool will not start. Air valve closed or obstructed.
-
Page 11: Replacement Parts
Replacement parts To order parts or reach our service department, call 1-800-274-6848 Monday through Friday, 8:00 a.m. to 5:00 p.m. CST. Please have the stock number and serial number of your tool available when you call, so that we may serve you quickly and accurately. ... - Page 12 #505710, JAT-710, Orbital (Jitterbug) Sander – exploded view JAT-710 Orbital (Jitterbug) Sander ...
- Page 13 #505710, JAT-710, Orbital (Jitterbug) Sander – parts list Index Part No. Description Index Part No. Description JAT710-01 Operating Lever 24 JAT710-24 End plate JAT710-02 Lever pin 25 JAT710-25 Rotor shaft JAT710-03 Metal strip 26 JAT710-26 Key JAT710-04 Rubber grip 27 JAT710-27 Gasket...
- Page 14 This page intentionally left blank. JAT-710 Orbital (Jitterbug) Sander ...
- Page 15 This page intentionally left blank. ...
- Page 16 427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.jettools.com JAT-710 Orbital (Jitterbug) Sander ...