Jet JOVS-10 Owner's Manual
  1. Manuals
  2. Brands
  3. Jet Manuals
  4. Sander
  5. JOVS-10
  6. Owner's manual

Jet JOVS-10 Owner's Manual

Oscillating spindle sander
Hide thumbs Also See for JOVS-10:
Table of Contents

Advertisement

Quick Links

OWNER'S MANUAL
JOVS-10 Oscillating Spindle Sander
WMH TOOL GROUP
Consumer/Light Industrial Products Division
P.O. BOX 1349
Auburn, WA 98071-1349
Ph: 1-800-274-6848 Fax: 1-800-274-6840
E-mail: jet@wmhtoolgroup.com
www.wmhtoolgroup.com
M-708411 11/02
Copyright © WMH Tool Group

Advertisement

Table of Contents
loading

Related Manuals for Jet JOVS-10

Summary of Contents for Jet JOVS-10

  • Page 1 OWNER'S MANUAL JOVS-10 Oscillating Spindle Sander WMH TOOL GROUP Consumer/Light Industrial Products Division P.O. BOX 1349 Auburn, WA 98071-1349 Ph: 1-800-274-6848 Fax: 1-800-274-6840 E-mail: jet@wmhtoolgroup.com www.wmhtoolgroup.com M-708411 11/02 Copyright © WMH Tool Group...

  • Page 2: Warranty

    This manual has been prepared for the owner and operators of a JOVS-10 Sander. Its purpose, aside from machine operation, is to promote safety through the use of accepted correct operating and maintenance procedures. Completely read the safety and maintenance instructions before operating or servicing the machine.

  • Page 3: Warnings

    Always keep guards in place and in proper operating condition. Do not operate the machine This sander is intended to be used with wood and wood products only. Use of this sander and a dust collector with metal products is a potential fire hazard.
  • Page 4 ALWAYS DISCONNECT THE MACHINE FROM THE POWER SOURCE BEFORE SERVICING. REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure the switch is in the off position before plugging in. USE RECOMMENDED ACCESSORIES. The use of accessories and attachments not recommended by JET may cause hazards or risk of injury to persons. NEVER STAND ON A MACHINE.

  • Page 5: Grounding Instructions

    115 Volt Operation As received from the factory, your sander is ready to run at 115 volt operation. This sander, when wired for 115 volt, is intended for use on a circuit that has an outlet and a plug that looks like the one illustrated in (A).

  • Page 6: Table Of Contents

    Specifications JOVS-10 Stock Number... 708411 Table Size ...24”W x 24”L Table Tilt (down) ...45 Dust Chute Diameter ...4” Spindle Speed (RPM) ... 1,725 Oscillations Per Minute ... 75 Length of Oscillation ...1-1/2” Motor (TEFC)... 1HP, 1Ph ... 115V Only Net Weight (approx.)...298 Lbs.

  • Page 7: Contents Of The Shipping Container

    Note: Now is a perfect time to set your sander up on a mobile base. It will make life easier in the woodshop. JET has a Heavy Duty Universal Mobile Base that will fit this sander.

  • Page 8: Mounting Sanding Sleeves

    (C, Fig. 3) while turning the arbor nut (D, Fig. 3) clockwise. Removing Sanding Assemblies 1. Disconnect the sander form the power source, unplug. 2. Use the provided wrenches to hold the upper arbor housing nut (E, Fig. 3) while turning the arbor nut (D, Fig.

  • Page 9: Table Insert

    Table Insert 1. Disconnect the sander form the power source, unplug. 2. Choose the insert (A, Fig. 4) that most closely matches the diameter of the sanding drum. 3. Line up the notch in the insert with the spring pin in the table (B, Fig. 4), and press in place.

  • Page 10: Replacing Sanding Sleeves

    Contact your local JET Distributor for more information. Maintenance The manufacturer recommends replacing the 90 SAE gear lube at 800 hours of use.

  • Page 11: Troubleshooting

    Machine vibrates excessively Sanded edge not square Sanding marks on wood Troubleshooting Possible Cause 1. Sander unplugged from wall or motor 2. Fuse blown or circuit breaker tripped 3. Cord damaged 4. Starting capacitor bad 1. Extension cord too light or too long 2.

  • Page 12: Breakdown And Parts List

    Breakdown for the JET Oscillating Spindle Sander...
  • Page 13 147 ...JOVS10-147 ... Motor..1 ...JOVS10-147MF ... Motor Fan (not shown) ..1 ...JOVS10-147MFC... Motor Fan Cover (not shown)..1 ...JOVS10-147CC ... Capacitor Cover (not shown)..1 Parts List for the JET JOVS-10 Oscillating Spindle Sander Size Qty.
  • Page 14 Index Part ...JOVS10-147RC ... Running Capacitor (not shown) ...45uf, 250V ... 1 ...JOVS10-147SC... Starting Capacitor (not shown) ...300MFD, 125VAC ... 1 148 ...JOVS10-148 ... Strain Relief Bushing ..1 149 ...TS-0720081 ... Lock Washer...5/16” ... 20 151 ...JOVS10-151 ... Coupling Head..1 152 ...JOVS10-152 ...
  • Page 15 Sanding Assemblies...
  • Page 16 Index Part Description 93 ...OVS10-093 ... Wrench..2 94 ...OVS10-094A... Arbor ...3/4” ... 6 95 ...OVS10-095 ... Hex Nut ..6 96 ...OVS10-096 ... Spring Pin...3.5x25... 3 97 ...30105000J ... P.V.C...4” ... 1 98 ...OVS10-098 ... Washer...4” ... 2 99 ...OVS10-099 ...
  • Page 17 Index Part Description Size Qty. 130 ...575800... Sanding Sleeve (100 Grit)...1/4” ..575801... Sanding Sleeve (120 Grit)...1/4” ... 133 ...OVS10-133A... Spindle ..1 165 ...JOVS10-165 ... Table Insert (medium)..1 166 ...JOVS10-166 ... Table Insert (small) ..1 167 ...JOVS10-167 ...

  • Page 18: Wiring Diagram

    Wiring Diagram...

Table of Contents