Related Manuals for Jet JAT-741
Summary of Contents for Jet JAT-741
- Page 1 Pneumatic 7in. Angle Polisher #505741, JAT-741 Operation & Parts Manual M-505741 Edition 3 11/2018 427 New Sanford Road LaVergne, TN 37086 Ph.: 800-274-6848 www.jettools.com Copyright © 2015 JET...
-
Page 2: Warranty And Service
Shop Tools; Warehouse & Dock products; Hand Tools; Air Tools NOTE: JET is a division of JPW Industries, Inc. References in this document to JET also apply to JPW Industries, Inc., or any of its successors in interest to the JET brand. -
Page 3: Safety Warnings
15. Excessive air pressure and too much free Do not use this tool for other than its intended rotation may decrease life of the tool and may use. If used for other purposes, JET disclaims cause a hazardous situation. any real or implied warranty and holds itself 16. - Page 4 32. Do not lubricate the tool with combustible how often you do this type of work. To reduce liquids, such as kerosene, diesel or jet fuel. your exposure to these chemicals, work in a 33. Do not dispose of this tool with normal well-ventilated area and work with approved household waste.
-
Page 5: About This Manual
As with any tool operation, safety of operator and bystanders should be first priority. If there are questions or comments, please contact your local supplier or JET. JET can also be reached at our web site: www.jettools.com. -
Page 6: Tool Specifications
Specifications were current at time of publication, but because of our policy of continuous improvement, JET reserves the right to change specifications at any time and without prior notice, without incurring obligations. -
Page 7: Setup And Assembly
Setup and Assembly air inlet. Any missing parts or damage should be reported Blow out air line to remove any dirt or immediately to your JET ® distributor. Do not use a moisture, then connect air supply hose to damaged tool. Read this instruction manual tool. - Page 8 General Air Tool Use a light oil containing rust inhibitors, such as Information SAE #10. Many JET air tools have integral oil reservoirs, which should be kept filled when in-line If the air tool is not performing according to oilers are not used.
- Page 9 Recycling Protect the environment. Your tool contains materials which can be recovered or recycled. When its useful life has expired, please leave tool at a specialized facility. Figure 2 Recommended arrangement of air piping and air line system...
- Page 10 Troubleshooting JAT-741 Angle Polisher Any disassembly of the tool should be done by qualified service personnel. For problems not addressed below, contact JET technical service at 800-274-6846. Problem Possible cause Remedy Tool will not start. Air valve closed or obstructed.
-
Page 11: Replacement Parts
Replacement parts Replacement parts are listed on the following pages. To order parts or reach our service department, call 1-800-274-6848 Monday through Friday, 8:00 a.m. to 5:00 p.m. CST. Please have the stock number and serial number of your tool available when you call, so that we may serve you quickly and accurately. - Page 12 #505741, JAT-741, 7in. Angle Polisher – exploded view JAT-741 Angle Polisher...
- Page 13 #505741, JAT-741, 7in. Angle Polisher – parts list Index Part No. Description Index Part No. Description JAT741-01 Motor housing JAT741-25 Retaining ring STW-16 JAT741-02 Valve housing JAT741-26 Wave washer WW-16 JAT741-03 Air inlet JAT741-27 Pinion gear JAT452-04 Throttle lever JAT741-28...
- Page 14 This page intentionally left blank. JAT-741 Angle Polisher...
- Page 15 This page intentionally left blank.
- Page 16 427 New Sanford Road LaVergne, Tennessee 37086 Phone: 800-274-6848 www.jettools.com JAT-741 Angle Polisher...