SAFETY WARNING! NEVER operate the mower unless the discharge guard and either the deflector assembly or the vacuum collector adapter are fastened securely in place. WARNING! Do not work around the mower deck boot or the blower area until you are certain that the mower blades and the blower impeller have stopped rotating.
PECO elects, without charge if the defect appears within 90 days from the date of installation of such part or before the expiration of the original warranty period, whichever is later.
From the underside of the engine remove the bolt and 1-1 Introduction bushing from the electric clutch assembly. Replace these We are pleased to have you as a PECO customer. Your parts with the engine pulley assembly P#(A0419), 7/16” collection system has been designed to give you a low lock washer P#(K0053), and 7/16”-20 x 4”...
Drill (2) 13/32” Holes Loosen Bolt To Rotate Air Cleaner Figure 2-1d PER SIDE Figure 2-1b Air Cleaner In Rotated Position USE TEMPLATE ON PAGE 21 NOTE: If air cleaner still touches after installing box assembly P#(A0794), there is adjustabity designed into the frame legs.
2-3 Main Frame Leg Installation Main Frame Assy. Figure 2-4 Install the left lower frame leg assembly P#(A0681) to the rear left side of the chassis by using (2) 3/8”-16 x 1” HHCS P#(K1191), (2) 3/8”-16 flange nuts P#(K1215), and (1) nut and bolt previously removed from the mower. Refer to the figures below.
2-6 Aluminum Grass Container 2-8 Belt Installation Installation Loosen the (2) bolts that secure the gear box assembly P#(A0429) to the pto mount plate (Figure 2-8a). Loosen NOTE: It is recommended that (3) people assist in the adjustment bolt P#(K0348) until the gear box mounting the container.
Page 11
MODEL#: 23621209 MOWER NAME: BOB-CAT MOWER MODEL: ZT-200 SERIES, PREDATOR PRO MOWER DECK SIZE: 61”, 52” & 48” DECK VAC NAME: 12 CUBIC FOOT BOX FOR YEAR: 2006 - BELOW PTO DRIVEN BILL OF MATERIAL: B0M0273 REVISED: NOTE: NOTE: A0685 UNIT ASSY.
Page 12
MODEL#: 23621212 MOWER NAME: BOB-CAT MOWER MODEL: ZT-200 SERIES (2007), PROCAT, PREDATOR PRO MOWER DECK SIZE: 61”, 52” & 48” DECK VAC NAME: 12 CUBIC FOOT BOX FOR YEAR: 2009 - 2007 PTO DRIVEN BILL OF MATERIAL: B0M0316 REVISED: NOTE: NOTE: A0988 UNIT ASSY.
Page 13
AIR CLEANER RELOCATION FOR BOB-CAT PREDATOR PRO Step 1 : Remove air cleaner end cap and remove filter (#1). Step 2: Remove hoses from air cleaner and intake (#2). Remove air cleaner. Step 3: Remove (4) bolts from intake (#3). Remove intake and all existing mounting bracket hardware. Step 4: Mount air cleaner mount plate P#(B0275) to intake using (4) original bolts (#4).
2-9 Dump Mechanism Adjustment 2-11 Boot Installation To mount the boot plate P#(B0079) to the boot The linkage may be adjusted in two places, at the P#(E1030), use (2) 3/8”-16 x 1” carriage bolts P#(K1182) adjusting screw P#(K1435) and the latch assembly and (2) 3/8”-16 flange nuts P#(K1215).
2-12 Blower Cone Installation 2-13 Impeller Blade Removal/Replacement Thread (1) 5/16”-18 jam nut P#(K0120) onto each end of (2) 5/16”-18 x 2-1/2” HHCS P#(K0125). Now partially To Remove: First remove the center bolt (#1), washer thread the bolts into each of the two tabs located on the (#2) and spacer (#3) from the taper-lock bushing (#5).
2-14 Length Of Hose Adjustment 2-17 Lower Hose To Boot Installation Take the unattached end of the lower hose and slide it The hoses in steps 2-15 and 2-16 must be cut to fit your over the circular end of the boot. Use the lower hose machine.
If there are any portions of the hose that have handle towards the mower. been torn or worn through, replace with genuine PECO parts. WARNING: The blower will continue to spin. DO NOT TOUCH the blower, pulleys, or the belt until the tractor is After Each Use: turned off.
3. Check belt for proper tension. 5-1 Parts And Service Information 4-2 Lubrication PECO collection system owners should record the name and telephone number of their Service Center. Your Service Center will be happy to supply replacement NOTE: Use only white lithium based grease for parts, accessories, and do any service or repairs to your lubrication of the shaft on the blower assembly.
SAFETY DECALS To promote safe operation, PECO supplies safety decals on all products manufactured. Damage can occur to safety decals either through shipment, use or reconditioning. Contact your local Service Center for replacement decals. Part #: R4027 Part #: R1053...
Page 21
DRAWING IS FULL SCALE. MAY BE USED A S A T EMPLATE. 4.00" 0.75" DRILL T EMPLATE FOR T HE T EXTRON REAR CHASSIS...
Page 22
P P P PECO PECO PECO PECO PECO 100 AIRPORT ROAD ARDEN, NORTH CAROLINA 28704 (800) 438-5823 OR (828) 684-1234 FAX: (828) 684-0858 EMAIL: peco@lawnvac.com WEBSITE: www.lawnvac.com...