Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Peco PRO 22 DFS
Summary of Contents for Peco PRO 22 DFS
- Page 1 P P P P P P PTO DRIVEN GRASS PECO PECO PECO PECO PECO COLLECTION SYSTEM Model# 752201, 752201-AM, 752202 Briggs & Stratton 10HP Vanguard 00752201 & 00752201-AM Yanmar 7HP Diesel 00752202 OPERATOR’S MANUAL ASSEMBLY OPERATION MAINTENANCE Initial Release - Oct 2019...
-
Page 2: Table Of Contents
GRASS COLLECTION SYSTEM TABLE OF CONTENTS SECTION PAGE SECTION PAGE Safety - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Length of Hose Adjustment - - - - - - - - - - - - - - - - - 21 Safety Alert Symbols - - - - - - - - - - - - - - - - - - - - - - 3 Upper Hose Installation - - - - - - - - - - - - - - - - - - - - 21... -
Page 3: Safety Alert Symbols
SAFETY WARNING! NEVER operate the mower unless the discharge guard and either the deflector assembly or the vacuum collector adapter are fastened securely in place. WARNING! Do not work around the mower deck boot or the blower area until you are certain that the mower blades and the blower impeller have stopped rotating. -
Page 4: Warranty
1. NO SERVICE CENTER WARRANTY The selling Service Center makes no warranty on his own on any item warranted by New PECO, Inc. unless he delivers to purchaser a separate written warranty certificate specifically warranting the item. The dealer has no authority to make any representation or promise on behalf of PECO or to modify the terms of this warranty in any way. -
Page 5: Introduction And Description
Section I - INTRODUCTION AND DESCRIPTION Introduction Description We are pleased to have you as a PECO customer. Your The grass collection system is designed for turf collection system has been designed to give you a low maintenance where there is a need to collect the grass maintenance, simple, and effective way to collect the clippings as the mower cuts the turf. -
Page 6: Installation For Use
Section II - INSTALLATION FOR USE Mower Preparations Lastly, install (2) Mounting Brackets to the top link arm and lower lift arms. Refer to Figure A for the positioning of the Mounting Brackets. Secure the Mounting Brackets to the top link arm by using (1) 3/4”-10 x 6” HHCS (Item #2) and (1) 3/4”... -
Page 7: Link Plates Assy & Installation
Link Plates Assembly & Installation To accommodate the Grass Collection System, adjust the lower lift arms of the three-point hitch. Viewing from the rear, measure from left to left of the Base Frame Brackets or right to right of the Base Frame Brackets to find the center of distance. -
Page 8: Base Frame 3-Pt Hitch Installation
Base Frame 3-Pt Hitch Installation Raise the Box and Main Frame Assembly until the Mounting Bracket of the Base Frame Assembly aligns with the top link hitch socket. Secure the top link hitch socket using (1) 3/4” x 3” Clevis Pin (Item #1) and (1) 7/16” x 1-3/4” Lynch Pin (Item #2). -
Page 9: Engine Mount Arm Assy Installation
Engine Mount Arm Assembly Installation Place the Engine Mount Arm Assembly (Item #1) up under the Right side of the Base Frame Leg. Align the hole of the Base Bracket to the hole on the Engine Mount Arm Assembly. Loosely secure using (1) 1/2”-13 x 3” HHCS (Item #2.1) and (1) 1/2”-13 Flange Nut (Item #2.4). -
Page 10: Engine / Blower / Blade Assy Installation
Engine/ Blower/ Blade Assembly Installation First position and place (2) Rubber Shock Absorbers (Item #3.1) on top of the Engine Mount Arm Assembly (Item #2). Next, Position the B&S 10HP Vanguard Blower/ Blade Assembly (Item #1) on top of the Rubber Shock Absorbers with the Blower facing towards the front of the tractor. -
Page 11: Throttle Kit Assy & Installation
Throttle Kit Assembly Installation To install the Throttle Cable Assembly (Item #2), locate the mounting slots on the Switch Plate of the Throttle Cable Assembly, refer to Figure A. Align the mounting slots of the Switch Plate to the holes located on the Upper Crossbar - Base Frame Assembly. Secure the Switch Plate using (2) 1/4”-20 x 2-1/4”... - Page 12 Throttle Kit Assembly Installation (Continued) For the B&S 10HP Vanguard To fasten the throttle cable end to the engine, place the throttle control lever into the “slow” position. Rotate the engine throttle lever to the “slow” position. Remove the screw on the engine next to the “fast” position of the throttle lever. Attach (1) Throttle Cable Sleeve Clamp, oriented with bent tab up and facing the engine, using the 10-32 x 3/4”...
-
Page 13: Wiring Kit Assy & Installation
Wiring Kit Assembly Installation To connect the Wiring Kit (P#A2152), connect the 4 gage Red Wire (P#P0620) to the positive (+) terminal of the starter solenoid on the engine. Route the Red Wire from the solenoid to the positive (+) terminal of the battery. Connect the 4 gage Black Wire (P#P0621) to one of the mounting bolt holes located on the bottom of the engine. - Page 14 Wiring Kit Assembly Installation (Continued) Figure B...
-
Page 15: Door Rod Pivot Assy & Installation
Door Rod Pivot Assembly & Installation Install the Door Rod Assembly (Item #2) to the Door Assembly (Item #1) by inserting the top end of the Door Rod Assy into the hole of the Door Support of the Door Assy. Secure the Door Rod Assy by using (1) Rue Ring Cotter Pin (Item #3) and (1) 1/2”... - Page 16 Door Rod Pivot Assembly & Installation (Continued) Next, assemble the Door Rod Pivot to the Base Frame Assembly by placing the straight end of the Door Rod Assembly (Item #1) through the Door Rod Pivot (Item #2). Secure each Door Rod Assy to the Door Rod Pivot with (1) 1/8”...
-
Page 17: Latch Handle Assy Installation
Latch Handle Assembly Installation Align and set the Latch Hook of the Latch Assembly (Item #2) to the Pivot Pin of the Box Base Frame Assembly. Refer to Figure A. Note: Some part features have been hidden from view for visual clarity. Figure A Latch Hook Pivot Pin... -
Page 18: Latch Rod Assy & Installation
Latch Rod Assembly & Installation Align and position the Latch Rod Assembly (Item #3) into the Handle of the Latch Assembly (Item #2). Secure the Latch Rod Assy by using (1) Rue Ring Cotter Pin (Item #7) and (1) 1/2” Flat Washer (Item #6). Next, position the Latch Release Lever through the of the Base Frame Assembly (Item #1) and over the Pivot Pin of the Door Assy. -
Page 19: Inlet, Inlet Ring & Debris Deflector Installation
Inlet, Inlet Ring & Debris Deflector Installation Open box door. From inside box, slide Inlet (Item #4) halfway into inlet hole (See Figure A). Take each half of the Inlet Ring (Item #2) and attach around matching groove in Inlet (Item #4). Slide Inlet (Item #4) & Inlet Ring (Item #2) against inlet hole and align four holes. -
Page 20: Sight Glass Kit Installation
Sight Glass Kit Installation Refer to Figure A for the complete breakdown of the Sight Glass Kit Part#(A2229). Figure A Open the Aluminum Box door. From inside of the Box, slide the assembled Sight Glass Kit into the window in the rear. Align the 8 screw holes of the Sight Glass Kit to those on the Aluminum Box and fasten the Sight Glass Kit to the Aluminum Box by using (8) #10-12 x 3/4”... -
Page 21: Length Of Hose Adjustment
Length Of Hose Adjustment Lower Hose To Blower Cone Installation The hoses in the following steps must be cut to fit your machine. Do not cut the hoses until you have tried to fit Slide a Hose Clamp P#(J0080) over both ends of the 8” them on your machine. -
Page 22: Impeller Blade Removal/Replacement
Impeller Blade Removal/Replacement To Remove: First remove the 7/16”-20 x 1” HHCS P#(K1394) (#1), 7/16” Double Indented Washer P#(K0278) (#3), (1) Tapered Washer P#(K0277) (#4) and (1) 3/8” Flat Washer P#(K0047) (#5) from the Taper-Lock Bushing P#(S4302) (#6). Next remove the (2) 1/4”-20 x 1” HHCS (#2) and place them into the threaded holes of the Taper- Lock Bushing (#6). -
Page 23: Exploded Views & Parts List
A7501 Pro22 DFS Exploded View... - Page 24 A7503 Pro22 DFS Exploded View...
- Page 25 A7500 Pro22 DFS / Base Model Exploded View...
- Page 26 A7500 Pro22 DFS / Base Model Exploded Parts List...
- Page 27 A0191 Door Assembly Exploded View...
- Page 28 A2236 Base Frame Assy / Pro 22 Exploded View...
- Page 29 A2234 Base Frame Assy / 3-Pt Hitch Exploded View...
- Page 30 A1212 Throttle Plate Assembly Exploded View...
-
Page 34: Safety Decals
SAFETY DECALS To promote safe operation, New PECO, Inc. supplies safety decals on all products manufactured. Damage can occur to safety decals either through shipment, use or reconditioning. Contact your local Service Center for replacement decals. P P P Part# R0022... -
Page 35: Operating Instructions
SECTION III OPERATING INSTRUCTIONS General Safety Unloading The Collection System Only qualified people familiar with this operator’s manual NOTE: Collection system blower will have an audible and the mower’s operator’s manual should operate this change in tone when the collection system is full. machine. -
Page 36: Lubrication
New PECO, Inc. and include 3. Under normal usage, the collection unit is subject to the following information on the chart below. -
Page 38: Troubleshooting
Troubleshooting 2017 (v1.0) Collection System Performance Problem Possible Cause Corrective Action — Cutting blades are bent or — Install new cutting blade unbalanced — Loose blower pulley or pulley Abnormal Vibration — Tighten the pulley assembly — Contact dealer to replace —... - Page 39 Notes...
- Page 40 P P P PECO PECO PECO PECO PECO New PECO, Inc. 10 Walden Dr | Arden, North Carolina 28704 Phone: 1-800-438-5823 | 828-684-1234 Fax: 828-684-0858 Email: peco@lawnvac.com Website: www.lawnvac.com...