1. Manuals
  2. Brands
  3. Peco Manuals
  4. Lawn Mower
  5. PTO3B
  6. Operator's manual

Peco PTO3B Operator's Manual

Driven grass collection system
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
P P P P P P
P P
P
P P
PECO
PECO
PECO
PECO
PECO
MANUAL PART#: Q0555
PTO DRIVEN GRASS
R
R R
COLLECTION SYSTEM
Model# 751501
Universal Category 1 - 3Pt Hitch Pro3 Bagger
OPERATOR'S MANUAL
ASSEMBLY
OPERATION
MAINTENANCE
Rev. 0 - Feb 2020

Advertisement

Table of Contents
loading

Related Manuals for Peco PTO3B

Summary of Contents for Peco PTO3B

  • Page 1 P P P P P P PTO DRIVEN GRASS PECO PECO PECO PECO PECO COLLECTION SYSTEM Model# 751501 Universal Category 1 - 3Pt Hitch Pro3 Bagger OPERATOR’S MANUAL ASSEMBLY OPERATION MAINTENANCE MANUAL PART#: Q0555 Rev. 0 - Feb 2020...

  • Page 2: Table Of Contents

    GRASS COLLECTION SYSTEM TABLE OF CONTENTS SECTION PAGE SECTION PAGE Safety - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Bag Assembly - - - - - - - - - - - - - - - - - - - - - - - - - 21 Safety Alert Symbols - - - - - - - - - - - - - - - - - - - - - - 3 Bag Assembly Installation - - - - - - - - - - - - - - - - - - 21...

  • Page 3: Safety Alert Symbols

    SAFETY WARNING! NEVER operate the mower unless the discharge guard and either the deflector assembly or the vacuum collector adapter are fastened securely in place. WARNING! Do not work around the mower deck boot or the blower area until you are certain that the mower blades and the blower impeller have stopped rotating.

  • Page 4: Warranty

    6. REMEDIED EXCLUSIVE: The only remedies the purchaser has in connection with the breach or performance of any warranty on New PECO, Inc. consumer products are set forth above. In no event will New PECO, Inc. be liable for special incidental or consequential damages.

  • Page 5: Introduction And Description

    Section I - INTRODUCTION AND DESCRIPTION Introduction Description We are pleased to have you as a PECO customer. Your The grass collection system is designed for turf collection system has been designed to give you a low maintenance where there is a need to collect the grass maintenance, simple, and effective way to collect the clippings as the mower cuts the turf.

  • Page 6: Installation For Use

    Section II - INSTALLATION FOR USE Mower Preparations Note: Read and review each step of this manual thoroughly. Review the instructions on Pg.15 carefully and be sure to understand the steps to properly adjust and run the PTO Slip Clutch to help prevent any damage. Before the installation of your unit, if applicable, prepare your tractor by removing the PTO Shroud from the rear of the tractor.

  • Page 7: Mower Preparations

    Mower Preparations (Continued) Lastly, install (2) Mounting Brackets to the top link arm and lower lift arms. Refer to Figure A for the positioning of the Mounting Brackets. Secure the Mounting Brackets to the top link arm by using (1) 3/4”-10 x 6” HHCS (Item #2) and (1) 3/4”...

  • Page 8: Link Plates Assy & Installation

    Link Plates Assembly & Installation To accommodate the Grass Collection System, adjust the lower lift arms of the three-point hitch. Viewing from the rear, measure either from the left to left of the Base Frame Brackets or the right to right of the Base Frame Brackets to find the center of distance.

  • Page 9: Base Frame 3-Pt Hitch Installation

    Base Frame 3-Pt Hitch Installation Raise the Main Frame Assembly until the Mounting Bracket of the Main Frame Assembly aligns with the top link arm. Secure the top link hitch socket using (1) 3/4” x 3” Clevis Pin (Item #1) and (1) 7/16” x 1-3/4” Lynch Pin (Item #2). Refer to Figure A.
  • Page 10 Base Frame 3-Pt Hitch Installation (Continued) Once the Top Link Arm and Lower Lift Arms have been secured, check the positioning of the unit and make adjustments as needed to ensure the unit is correctly positioned. Refer to Figure C for correct unit position. NOTE: Some part features have been hidden from view for visual clarity.

  • Page 11: Pto Drive Assy & Installation

    PTO Drive Assembly & Installation Position the PTO Drive Assy (Item #2) under the Base Frame Assy (Item #1) and align the mounting holes of the Drive Mount Brackets to those of the front set, outermost Base Frame Bracket. Refer to Figure A & Figure B. NOTE: Some part features have been hidden from view for visual clarity.

  • Page 12: Pto Drive Stand & Stand Foot Assy

    PTO Drive Stand & Stand Foot Assembly Install the Stand Foot Sub Assembly (Item #2) to the PTO Drive Stand Assembly (Item #1) by securing the Stand Foot (Item #2.1) to the Stand Pivot Assembly by using (2) 5/16” U-Bolt (Item #2.2) and (4) 5/16” Ny-flange Lock Nuts (Item #2.3).
  • Page 13 Jack Stand Assembly & Installation Your Collection Unit will include an A-Frame Jack (Item #1) with a Jack Foot (Item #2) and a separate Jack Stand Bracket (Item #3). Assemble the A-Frame Jack to the Jack Stand Bracket by using (2) 3/8”-16 x 1” GR5 HHCS (Item #4.1), (2) 3/8”...

  • Page 14: Jack Stand Assy & Installation

    Jack Stand Assembly & Installation (Cont.) While not in use or being stored, turn the Jack Stand Assy horizontal and secure the Jack Stand Assy to the PTO Drive Assy using (1) Detent Pin (Item #4.4, Fig. A, Pg. 13) and (1) Hair Pin Clip (Item #4.5, Fig.

  • Page 15: Pto Driveshaft Assy Installation

    PTO Driveshaft Assembly Installation It is recommended to lubricate the sliding members of the PTO Driveshaft and universal joints before assembly and installation. The universal joints can be found in between the Quick Connect Yoke as well as the Driveshaft Yoke. Refer to the Lubrication Instructions on page 43.

  • Page 16: Pto Slip Clutch Adjustments

    PTO Driveshaft Assembly Installation (continued) Install the PTO Slip Clutch P#(M0006) onto the tractor’s PTO and tighten the shaft clamping bolts to 75 ft/lbs to secure the PTO Slip Clutch. Next, Connect the Driveshaft from the PTO Drive Assy to the PTO Slip Clutch using the Quick Connect Yoke to secure the Driveshaft to the Slip Clutch.

  • Page 17: Mount Tube Installation

    Mount Tube Installation Position (1) Tube Mount Bracket (Item# 3) to the top frame of the Base Frame Assy (Item# 1) either to the far right or left of the Base Frame Assy. Refer to Figure A. Secure the Tube Mount Bracket relatively loose by using (2) 5/16”-18 U-Bolts (Item# 4) and (2) 5/16”-18 Ny-Flange Lock Nuts (Item# 5) on to the (2) lower set of bolt holes, refer to Figure B for visual clarity.

  • Page 18: Upper Frame Assy Installation

    Upper Frame Assembly Installation Position the Upper Frame Assembly (Item #1) above the Lower Mount Tubes as shown in Figure A. Slide the Upper Frame Assembly down onto the Lower Mount Tubes and secure using (2) Clevis Pins (Item #2) and (2) Rue Ring Cotter Pin Clips (Item #3).

  • Page 19: Top Assy To Upper Frame Assy Installation

    Top Assembly To Upper Frame Assembly Installation Align the Top Assembly Pivot Holes to the Upper Frame Assembly. See Figure A below. Before fastening, pull Rubber Dust Guard outward to seal against Upper Frame Assembly (towards the mower’s operator seat). Fasten the Top Assembly to the Upper Frame Assembly using (2) 5/16”-18 x 2-1/2”...

  • Page 20: Hinge Kit Assy Installation

    Hinge Kit Assembly Installation Assemble the Hinge Kit using (1) Latch Plate P#(B0884), (1) 5/16”-18 x 1-1/4” HHCS P#(K1156), (1) 5/16”-18 Ny- Flange Lock Nut P#(K2516), (3) 5/16” Flat Washers P#(K0042), (1) Latch Spacer P#(S0006), (2) Extra Heavy 5/16” Fender Washers P#(K0505) and (1) 5/16”-18 Lock Nut P#(K0506). Leave the nuts loose enough to allow fluid movement of the top when opening and closing.

  • Page 21: Bag Assembly

    Bag Assembly First, take one of the Bag Ring Split Ends and insert it through the Bag Seam Opening. Next, rotate the Bag around the Bag Ring (1) full turn (360 degrees) until the Bag Ring Split Ends and the Bag Seam Opening are positioned on the same side.

  • Page 22: Slow Moving Vehicle Label Installation

    Slow Moving Vehicle Label Installation The Slow Moving Vehicle (SMV) Label will need to be visible from the back of your tractor if you’re required to have one. If the Collection Unit is obstructing the SMV Label from view, the SMV Label will need to be repositioned. To reposition the SMV Label that came with your tractor, first, install the SMV Sign Mount (Item #1) to the base of the Main Frame Assy of your grass collection unit.

  • Page 23: Length Of Hose Adjustment

    Length Of Hose Adjustment Lower Hose To Blower Cone Installation The hoses in the following steps must be cut to fit your machine. Do not cut the hoses until you have tried to fit Slide a Hose Clamp over both ends of the your Lower them on your machine.

  • Page 24: Impeller Blade Removal/Replacement

    Impeller Blade Removal/Replacement To Remove: First remove the 7/16”-20 x 1” HHCS P#(K1394) (#1), 7/16” Double Indented Washer P#(K0278) (#2) and (2) 3/8” x 15/16” Bushing P#(S0159) (#4) from the Taper-Lock Bushing P#(S4302) (#5). Next remove the (2) 1/4”- 20 x 1” HHCS (#3) and place them into the threaded holes of the Taper-Lock Bushing (#5). Gradually thread each bolt evenly into the Taper-Lock Bushing, forcing the blade to break-away from the Taper-Lock Bushing.

  • Page 25: Pto Drive System Diagram

    PTO Drive System Diagram Never engage the PTO unit at full speed. The PTO unit should only be engaged at idle speeds, then gradually increased to the desired speed. Refer to Figure A for the PTO Drive System Diagram and Figure B for the directional rotation of each gearbox shaft.

  • Page 26: Exploded Views & Parts List

    A1157 Pro3B Standard Top Exploded View...
  • Page 27 A2223 Top Assy / Base Model Exploded View...
  • Page 28 A2280 5-Blade Impeller Drive Assy Exploded View...
  • Page 29 A2279 PTO Drive Assy Exploded View...
  • Page 30 A2238 PTO Inter Connect Shaft Sub Assy Exploded View...
  • Page 31 A2237 PTO Drive Stand Assy Exploded View...
  • Page 32 A2263 Stand Foot Sub-Assy Exploded View...
  • Page 33 A2236 Base Frame Assy / Pro 22 Exploded View...
  • Page 34 A2234 Base Frame Assy / 3-Pt Hitch Exploded View...
  • Page 35 A2257 PTO Drive Shaft Assy Exploded View...

  • Page 39: Safety Decals

    SAFETY DECALS To promote safe operation, New PECO, Inc. supplies safety decals on all products manufactured. Damage can occur to safety decals either through shipment, use or reconditioning. Contact your local Service Center for replacement decals. P P P PECO...

  • Page 40: Operating Instructions

    SECTION III OPERATING INSTRUCTIONS General Safety Disengagement Of The PTO Assembly Only qualified people familiar with this operator’s manual A. To disengage the PTO assembly, move the tractor’s and the mower’s operator’s manual should operate this PTO switch to the off position. machine.

  • Page 41: Lubrication

    If for any reason your Service Center is unable to service your collection system or supply replacement parts, contact New PECO, Inc. and include the following information on the chart below. DOCUMENT THE FOLLOWING INFORMATION FOR FUTURE REFERENCE...

  • Page 43: Troubleshooting

    Troubleshooting 2017 (v1.0) Collection System Performance Problem Possible Cause Corrective Action — Cutting blades are bent or — Install new cutting blade unbalanced — Loose blower pulley or pulley Abnormal Vibration — Tighten the pulley assembly — Contact dealer to replace —...
  • Page 44 P P P P P P PECO PECO PECO PECO PECO New PECO, Inc. 10 Walden Dr | Arden, North Carolina 28704 Phone: 1-800-438-5823 | 828-684-1234 Fax: 828-684-0858 Email: peco@lawnvac.com Website: www.lawnvac.com...

Table of Contents