Related Manuals for Peco GRAVELY-200 12621214
Summary of Contents for Peco GRAVELY-200 12621214
- Page 1 P P P GRASS COLLECTION PECO PECO PECO PECO PECO SYSTEM DESIGNED FOR: MODEL 12621214 GRAVELY 200 SERIES MOWER OPERATOR’S MANUAL ASSEMBLY OPERATION MAINTENANCE MANUAL PART#: Q0339 $4.00 REV: 1...
-
Page 2: Table Of Contents
PTO GRASS COLLECTION SYSTEM TABLE OF CONTENTS SECTION PAGE SECTION PAGE Safety - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 2-12 The Length Of Hose Adustment - - - - - - - - - - - 16 Safety Alert Symbols - - - - - - - - - - - - - - - - - - - - - - 3 2-13 Upper Hose Installation - - - - - - - - - - - - - - - - 16... -
Page 3: Safety Alert Symbols
SAFETY WARNING! NEVER operate the unit unless the discharge guard and either the deflector assembly or the vacuum collector adapter are fastened securely in place. WARNING! Do not work around the mower deck boot or the blower area until you are certain that the mower blades and the blower impeller have stopped rotating. -
Page 4: Warranty
PECO elects, without charge if the defect appears within 90 days from the date of installation of such part or before the expiration of the original warranty period, whichever is later. -
Page 5: Introduction And Description
1-1 Introduction Section II INSTALLATION FOR USE We are pleased to have you as a PECO customer. Your collection system has been designed to give you a low 2-1 Preparation Of Mower maintenance, simple, and effective way to collect the grass clippings from your mower. -
Page 6: Lower Frame Leg Installation
2-2 Lower Frame Leg Installation Remove the (3) bolts (Figure 2-2a) from each side of the rear of the mower. Keep the bolt, from each side, that Figure 2-2b threads through the mower’s rear frame. Place the left lower main frame leg assembly P#(A0511) onto the rear of the mower and fasten by using (2) 3/8”-16 x 3”... -
Page 7: Top Main Frame Assembly Installation
Figure 2-2d RED/VIOLET PECO BAGGER SWITCH BRN/YELLOW 2-3 Top Main Frame Assembly 2-4 Lift Handle Installation Installation The various parts of the box handle assembly P#(A0614) must be attached to the container frame. Place the top main frame assembly P#(A0944) (Figure... -
Page 8: Aluminum Grass Container Installation
2-5 Aluminum Grass Container 2-6 Aluminum Grass Container Inlet Installation Attachment NOTE: It is recommended that (3) people assist in The inlet will need to be attached to the container (See mounting the container. page 9). Open the container, push the inlet from the inside of the container through the hole in the container With three people available, two can lower the container to the outside. -
Page 9: Exploded Parts Views And Assemblies
Lift Handle Assembly Aluminum Grass Container Assembly Aluminum Grass Container With Handle Attached Latch Hook Mechanism Assembly... - Page 10 Aluminum Grass Container Exploded View (1) C0025 (1) B8113 Box Top (1) C0029 Screen Screen Support (1) C0023 (4) B1668 Box Back & Inlet Clamp Sides (1) A0614 (1) C1184 (1) V1054 (1) A0938 Box Handle Fill Gage Inlet Box/Door Frame (1) J0522 (1) B1730...
- Page 11 Exploded Parts View...
- Page 12 PTO Parts List...
- Page 13 A0633 UNIT ASSY. V1054 6” PLASTIC HB0235 J6006 INLET HARDWARE 7” - 8” HOSE CLAMP A0794 12 CU. FT. BOX ASSY. HB0237 8" x 38” ENGINE PULLEY LWR. HARDWARE HOSE 6” x 36” UPR. HOSE A0603 PTO HANDLE ASSY. A0944 A0614 E6009 BOX HANDLE...
-
Page 14: Universal Pto Installation
2-9 Belt Installation 2-8 Universal PTO Installation Loosen the (4) bolts P#(K1191), (2) on each side, that To mount the PTO assembly, insert the mount rod on the secure the gear box assembly to the PTO assembly PTO assembly P#(A0623) into the mounting slots P#(A0423) (Figure 2-9a). -
Page 15: Cam Assembly Adjustment
Figure 2-11a (1) 3/8”-16 x 3/4” HHCS 2-10 Cam Assembly Adjustment (1) 3/8” Lock Washer The cam assembly P#(A0422), which controls the blower belt tension, comes from the factory pre-adjusted. If the belt is too tight or becomes too loose, remove the hair pin clip P#(K0099) from the belt tension rod P#(K0326) and pull the “L”... -
Page 16: The Length Of Hose Adustment
2-12 The Length Of The Hose 2-14 Lower Hose To Blower Cone Adjustment Installation The hoses in steps 2-13 and 2-14 must be cut to fit your Slide a 7”-8” hose clamp P#(J6006) over both ends of machine. Follow steps 2-13 and 2-14. Do not cut the the lower hose. -
Page 17: Blower Cone Installation
2-17 Blower Cone Installation 2-18 Impeller Blade Removal/Replacement Thread (1) 5/16”-18 jam nut P#(K0120) onto each end of (2) 5/16”-18 x 2-1/2” HHCS P#(K0125). Now partially To Remove: First remove the center bolt (#1), washer thread the bolts into each of the two tabs located on the (#2) and spacer (#3) from the taper-lock bushing (#5). -
Page 18: Final Checks
* Mow twice, at different height settings, (high, then low), 2-19 Final Checks if grass is extra tall. * Remember that horsepower requirements will vary with To check the operation of the safety interlock harness the mowing conditions such as type and height of turf perform the following: grass, moisture content, amount of leaves, whether the terrain is flat or hilly, etc. -
Page 19: Lubrication
Check the belt tension and inspect the pulley belt for cracks or tears. PECO collection system owners should record the name 7. Check for wear or deterioration of the upper or lower and telephone number of their Service Center. Your hoses. -
Page 20: Safety Decals
SAFETY DECALS To promote safe operation, PECO supplies safety decals on all products manufactured. Damage can occur to safety decals either through shipment, use or reconditioning. Contact your local Service Center for replacement decals. Part #: R4027 Part #: R1053... - Page 22 P P P PECO PECO PECO PECO PECO P.O. BOX 1197 ARDEN, NORTH CAROLINA 28704 (800) 438-5823 OR (828) 684-1234 FAX: (828) 684-0858 EMAIL: peco@lawnvac.com WEBSITE: www.lawnvac.com...