Furuno FR-8045 Installation Manual
  1. Manuals
  2. Brands
  3. Furuno Manuals
  4. Marine Radar
  5. FR-8045
  6. Installation manual
Furuno FR-8045 Installation Manual

Furuno FR-8045 Installation Manual

Hide thumbs Also See for FR-8045:
Table of Contents

Advertisement

Quick Links

See also: Operator's Manual
Installation Manual
MULTI-COLOR LCD RADAR
FR-8045/FR-8065/FR-8125/FR8255
Model
Product Name: MARINE RADAR
SAFETY INSTRUCTIONS ................................................................................................ i
SYSTEM CONFIGURATION ........................................................................................... ii
EQUIPMENT LISTS........................................................................................................ iii
1. HOW TO INSTALL THE SYSTEM ............................................................................. 1
1.1 Display Unit...........................................................................................................................1
1.2 Antenna Unit Installation .......................................................................................................5
1.3 Power Supply Unit ..............................................................................................................19
2. CABLE CONNECTION AND WIRING ..................................................................... 20
2.1 Standard Connection ..........................................................................................................20
2.2 Wiring the Power Supply Unit (FR-8255 only) ....................................................................21
2.3 Data Signals........................................................................................................................23
2.4 Input/Output Ports...............................................................................................................23
3. EQUIPMENT SETTINGS.......................................................................................... 25
3.1 Setting the Language..........................................................................................................25
3.2 How to Set the Purpose ......................................................................................................26
3.3 How to Enter Initial Settings................................................................................................27
4. OPTIONAL EQUIPMENT ......................................................................................... 31
4.1 ARP Kit ARP-11..................................................................................................................31
4.2 Connection of Buzzer and/or Remote Display ....................................................................33
PACKING LISTS ......................................................................................................... A-1
OUTLINE DRAWINGS ................................................................................................ D-1
INTERCONNECTION DIAGRAMS.............................................................................. S-1
www.furuno.com
All brand and product names are trademarks, registered trademarks or service marks of their respective holders.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FR-8045 and is the answer not in the manual?

Questions and answers

Related Manuals for Furuno FR-8045

Summary of Contents for Furuno FR-8045

  • Page 1: Table Of Contents

    Installation Manual MULTI-COLOR LCD RADAR FR-8045/FR-8065/FR-8125/FR8255 Model Product Name: MARINE RADAR SAFETY INSTRUCTIONS ....................i SYSTEM CONFIGURATION ................... ii EQUIPMENT LISTS......................iii 1. HOW TO INSTALL THE SYSTEM ................1 1.1 Display Unit...........................1 1.2 Antenna Unit Installation .......................5 1.3 Power Supply Unit ......................19 2.

  • Page 2: Safety Instructions

    Serious injury or death can result if someone falls within a certain sector of antenna revolution. This is from the radar mast. possible - Ask your FURUNO representative or Turn off the power at the mains switchboard dealer to provide this feature.

  • Page 3: System Configuration

    SYSTEM CONFIGURATION Model FR-8065 Model FR-8125 Model FR-8255 Antenna Unit Antenna Unit Antenna Unit Model FR-8045 XN-12A-RSB-0070-085A XN-12A-RSB-0070-086A XN-12A-RSB-0070-087A Antenna Unit XN-12A-RSB-0073-085A XN-12A-RSB-0073-086A XN-12A-RSB-0073-087A XN-12A-RSB-0073-088B XN-13A-RSB-0070-085A XN-13A-RSB-0070-086A XN-13A-RSB-0070-087A XN-13A-RSB-0073-088B XN-13A-RSB-0073-085A XN-13A-RSB-0073-086A XN-13A-RSB-0073-087A Antenna Power Supply PSU-008 Display unit 24 VDC...

  • Page 4: Equipment Lists

    CP03-33030 000-014-607 20m Cable CP03-33040 000-014-608 30m Cable For Antenna Unit: CP03-33801 001-141-670 FR-8065/FR-8125/FR-8255 CP03-18401 008-503-360 For Antenna Unit: FR-8045 CP03-22901 008-219-760 For Radiator CP03-30600 000-084-769 For PSU-008 Spare Parts SP03-17701 001-258-000 For Display Unit: Fuse (Code: 000-155-826-10, FGBO 125V 10A PBF)
  • Page 5 EQUIPMENT LISTS Optional supply Name Type Code No. Comments Auto Plotter ARP-11 008-523-050 External Alarm OP03-21 000-030-097 Buzzer MJ-B24LPF0010-100+R 000-147-880-12 MJ-B24LPF0010-200+R 000-147-881-12 For Remote Display Unit MJ-B24LPF0010-300+R 000-147-882-12 Signal Cable MJ-A7SPF0007-050C 000-154-028-10 For NMEA1/2 Assembly MJ-A6SPF0007-100C 000-159-695-10 For Heading Sensor MJ-A10SPFW0001+R 001-074-600-10 For Remote Display Unit/...

  • Page 6: How To Install The System

    Display Unit Select a location for the display unit by following the information shown below. • The unit is waterproof, but FURUNO recommends that you install the display unit in a cabinet. • Keep the unit away from direct sunlight.
  • Page 7 1. HOW TO INSTALL THE SYSTEM 1.1.1 How to install the display unit How to install the display unit on a desktop or overhead Follow the procedure shown below to install the display unit on a desktop or overhead. 1. Unfasten the knob bolts and remove the display unit from the hanger. 2.
  • Page 8 1. HOW TO INSTALL THE SYSTEM How to install the display unit in a console Note 1: Requires Flush Mount Kit OP03-228 (Option). Note 2: The unit must be installed in a flat area of the console. Ensure there is ample room behind the unit once installed to allow access for maintenance.
  • Page 9 1. HOW TO INSTALL THE SYSTEM 6. Adjust the flush-mounting fixture by loosening the wingnuts and wingscrews to al- low the bolt free movement. Use the figure below for reference. Flush-mounting fixture Minimal distance between protector and clamp. 7. Attach the flush-mounting fixture to the unit referring to the diagram below. Flush-mounting fixture Console M8×15 Bolt...

  • Page 10: Antenna Unit Installation

    1. HOW TO INSTALL THE SYSTEM Antenna Unit Installation How to select the location for the antenna unit • The antenna unit is installed either on top of the wheelhouse or a platform on the radar mast. Install the antenna unit where there is a good complete view. Any ob- struction causes blind sectors.

  • Page 11: Installation Procedure

    1. HOW TO INSTALL THE SYSTEM 1.2.1 Installation procedure Refer to the outline drawing at the back of this manual for the dimensions. Make five holes in the platform. Four holes to fasten the antenna unit and one hole for the signal cable.
  • Page 12 1. HOW TO INSTALL THE SYSTEM 1.2.2 How to install the antenna unit You can install the antenna unit by one of the two methods shown below. • Use the outside holes • Use the inside holes How to use outside holes of the antenna housing Use the hex head bolts (supplied) to install the antenna unit as shown in the illustration below.
  • Page 13 1. HOW TO INSTALL THE SYSTEM 3. Set four hex head bolts (M12×60, supplied) and seal washers (supplied) from the top of the antenna housing, as shown below. Hex bolt Seal washer Flat washer Spring washer 4. Set the flat washers (M12, supplied), spring washers (supplied) and nuts (sup- plied) to the hex head bolts.
  • Page 14 1. HOW TO INSTALL THE SYSTEM 1.2.3 How to use the inside holes of the antenna housing (FR-8045) This method requires removal of the RF unit from the antenna unit to access the inside fixing holes. Use four hex head bolts, flat washers, spring washers and nuts (local sup- ply) to install the antenna unit.
  • Page 15 1. HOW TO INSTALL THE SYSTEM 1.2.4 How to connect the signal cable (FR-8045) The signal cable runs from the display unit to the antenna unit. To reduce the electrical interference, do not run the signal cable near other electrical equipment. Also do not run the cable in parallel to power cables.
  • Page 16 1. HOW TO INSTALL THE SYSTEM 5. Put the signal cable so that no more than 4 cm of the sheath is visible, as shown in the figure below. Tighten the fixing bolts. Taping Shield wire Sheath Bolt Within 4 cm Plate Gasket Flat...
  • Page 17 1. HOW TO INSTALL THE SYSTEM 9. Attach three EMI cores to the signal cable as shown below. RTB Board J821 VH9P J822 VH2P J824 NH13P Lead in J823 VH4P cable here. EMI core RFC-13 Clamp Run cable along here. 10.
  • Page 18 1. HOW TO INSTALL THE SYSTEM 1.2.5 How to use the inside holes of the antenna housing (FR-8065/FR-8125/FR-8255) This method requires removal of the RF unit in the antenna unit to access inside fixing holes. Use hex head bolts, flat washers, spring washers and nuts (local supply) to mount the antenna unit, confirming length of bolts.
  • Page 19 1. HOW TO INSTALL THE SYSTEM 1.2.6 How to connect the signal cable (FR-8065/FR-8125/FR-8255) Only the signal cable runs from the display unit (power supply unit in case of FR-8255) to the antenna unit. In order to minimize the chance of picking up electrical interfer- ence, avoid where possible routing the signal cable near other onboard electrical equipment.
  • Page 20 1. HOW TO INSTALL THE SYSTEM Connecting the signal cable 1. Open the antenna cover by loosening four bolts, and then fix the stay. Cable entry RTB board cover Antenna unit chassis, cover opened 2. Unfasten the cable gland assembly (plate, gasket, flat washer). The plate may be discarded.
  • Page 21 1. HOW TO INSTALL THE SYSTEM 5. Fasten the shielded part of the signal cable with shield clamp (installation materi- al) as shown below. Shield clamp Signal cable Fix shield wire with bolt. Gasket support Cable Entry How to fix signal cable in cable gland 6.
  • Page 22 1. HOW TO INSTALL THE SYSTEM 9. Attach three EMI cores to the signal cable as shown below. EMI Core RFC-13 (2 pcs) EMI Core RFC-H13 (1 pc) Antenna unit chassis, cover opened 10. Fix the signal cable with the cable clamp as follows. a) Dismount the cable clamp plate and remove clamp and gasket.
  • Page 23 1. HOW TO INSTALL THE SYSTEM b) Run the signal cable as shown below. c) Fix the signal cable with cable clamp as shown below. Cable clamp RTB board cover Top view 11. Release the stay and close the cover. Loosely fasten the antenna bolts; you will have to make some adjustments inside after completion of wiring.

  • Page 24: Power Supply Unit

    1. HOW TO INSTALL THE SYSTEM Power Supply Unit A power supply unit is shipped with the FR-8255, because of its high power consump- tion. The power supply unit can be installed almost anywhere provided the location is dry, well-ventilated, sufficient maintenance space is provided and is installed within 5 m (cable length) from the display unit.

  • Page 25: Cable Connection And Wiring

    Connect all necessary cables, using the figure and table below for reference. CAUTION Ground the equipment to prevent interference. Description Cable Required Antenna cable to antenna unit (FR-8045) MJ-B24LPF0005-*+R *: 50/100/150/200/300 MJ-B24LPF0012-*+R Antenna cable to antenna unit. (FR-8065/8125) *: 100/150/200/300 • MJ-B24LPF0011-050+R Antenna cable to antenna unit. (FR-8255) •...

  • Page 26: Wiring The Power Supply Unit (Fr-8255 Only)

    2. CABLE CONNECTION AND WIRING Wiring the Power Supply Unit (FR-8255 only) 2.2.1 Cabling 1. Unfasten four screws to remove the cable clamp. 2. Unfasten four screws to remove the cover. 3. Attach the connectors of three cables as shown in the figure below. POWER Board 03P9419 J1 3P Ground...
  • Page 27 2. CABLE CONNECTION AND WIRING 2.2.2 Jumper block, slide switch setting The jumper block JP1 and slide switch S112 on the PWR board (03P9419) must be set according to radar model. Open the unit, locate JP1 and S112 and set them as below.

  • Page 28: Data Signals

    2. CABLE CONNECTION AND WIRING Data Signals Position GNS>GGA>RMC> GLL Course true VTG>RMC Course magnetic VTG>RMC (true) Speed over the ground VTG>RMC Water speed and heading Distance to waypoint BWR>BWC>RMB Destination waypoint, true BWR>BWC>RMB Destination waypoint, magnetic BWR>BWC Heading (true) THS>HDT>VHW (true)>HDG>HDM>VHW (magnetic) Heading (magnetic) HDG>...
  • Page 29 2. CABLE CONNECTION AND WIRING 2.4.2 NMEA1 ports Transmitter This port complies with “IEC 61162-1 Ed4”. Parameter Rating Remarks Circuit Diagram “H” level -60mA Absolute Differential Driver output current Maximum “L” level 60mA Absolute TD1_A output current Maximum Differential 1.5V (MIN) Load 54Ω...

  • Page 30: Equipment Settings

    EQUIPMENT SETTINGS Setting the Language After installation, on first power-up, select a language as follows: 1. Press the /BRILL key to turn on the power. "Now Initializing" appears and after a short time the window below appears. 2. Use the CursorPad to select a language required and press the ENTER key. The window shown below appears.

  • Page 31: How To Set The Purpose

    10. Press the ENTER key to show the setting window. The default setting is [8065 RTR-085A]. Note: For FR-8045, the default is [8045 RTR-088A]. No adjustment is necessary, go to step 13. 11. Press  or  to select the appropriate model.

  • Page 32: How To Enter Initial Settings

    3. EQUIPMENT SETTINGS How to Enter Initial Settings After you complete setting the radar purpose, enter the Initial Settings as follows: 1. On the main menu, press to select [Installation]. Page 1 Menu Installation Input Source : Master ARPA ARPA QV Select : Off Demo Mode : Off...
  • Page 33 3. EQUIPMENT SETTINGS Basic settings [Input source]: Select the input source from [Master] and [Slave]. The default setting is [Master]. Master The display unit operates as the main radar. Slave The display unit operates as a remote display. For remote displays, adjust the [Video Init Adjust] and [Timing Adjust].
  • Page 34 3. EQUIPMENT SETTINGS How to automatically set the equipment The equipment can automatically adjust the tuning, timing and video. Note: Before you proceed, transmit the radar for more than 10 minutes on a long range and ensure [Sector Blank] is set to [OFF]. 1.
  • Page 35 3. EQUIPMENT SETTINGS Manual MBS adjustment Reduce the main bang (black hole), which appears at the display on short ranges, as follows: 1. Transmit the radar on the shortest range. 2. Open the [Installation] menu and select [MBS Adjust]. 3. Press ENTER to show the setting window. 4.

  • Page 36: Optional Equipment

    OPTIONAL EQUIPMENT ARP Kit ARP-11 The ARP kit provides automatic radar plotter functions to this radar. Necessary parts Name ARP kit Type ARP-11 Code No. 008-523-050 For the contents of the kit, see the packing list attached to the kit. 1.
  • Page 37 4. OPTIONAL EQUIPMENT 3. Mate P107 on the ARP Circuit-board with J214 on the 03P9586 Board and fasten with four screws. ARP board Confirm that the rubber gasket is set securely in the groove around the panel. 4. Reassemble the display unit, taking care not to exceed the torque requirements for each connector nut.

  • Page 38: Connection Of Buzzer And/Or Remote Display

    4. OPTIONAL EQUIPMENT Connection of Buzzer and/or Remote Display You will need the cables shown below to connect the optional external buzzer and re- mote display. • Two-way cable MJ-A10SPFW0001 +R • MJ-A7SPF0007-050C • MJ-B24LPF0010-xxx+R (000: 100, 200, or 300) MJ-A10SPFW0001+R * (0.2 m) Display unit RDP-154...
  • Page 48 ・FURUNO Authorized Distributor/Dealer 9-52 Ashihara-cho, Nishinomiya, 662-8580, JAPAN A : JAN 2014 Printed in Japan All rights reserved. B : AUG . 25, 2014 Pub. No. IME-36320-B ( AKMU ) FR-8045/8065/8125 0 0 0 1 7 8 5 0 7 1 1...

This manual is also suitable for:

Fr-8125Fr-8065Fr-8255

Table of Contents