Lighting Procedure; Manual Ignition - Jumbuck HS-UM006D Assembly & Operation Instructions

LIGHTING PROCEDURE

LIGHTING PROCEDURE
Lighting the barbecue is easy, but must be done with due care. Lighting the barbecue is easy, but must be done with due care.
Make sure that gas is turned on at the cylinder, or that gas is available to the barbecue.
Make sure the LPG cylinder is filled. Make sure the LPG cylinder is filled.
Check that the end of each burner tube is properly located over each valve orifice. Check that the end of each burner tube is properly located over each valve orifice. Check that the end of each burner tube is properly located over each valve orifice.
Make sure all gas connections are securely tightened. Make sure all gas connections are securely tightened.
Open the grill lid
Line the grease tray with "crumpled

MANUAL IGNITION

Place a lighted match or gas lighter (not provided). Keep your hand below the bottom of the Place a lighted match or gas lighter (not provided). Keep your hand below the bottom of the Place a lighted match or gas lighter (not provided). Keep your hand below the bottom of the
burner while doing this. Now turn the burner on. You should see the burner alight. burner while doing this. Now turn the burner on. You should see the burner alight. burner while doing this. Now turn the burner on. You should see the burner alight. Repeat to light
the other burners.
FLAME THROWER IGNITION FLAME THROWER IGNITION
These barbecues are equipped with automatic ignition, as indicated on the front face of the barbecue These barbecues are equipped with automatic ignition, as indicated on the front face of the barbecue These barbecues are equipped with automatic ignition, as indicated on the front face of the barbecue
frame. It works by throwing a flame to the side of the burner to light. Push the knob in and turn frame. It works by throwing a flame to the side of the burner to light. Push the knob in and tur frame. It works by throwing a flame to the side of the burner to light. Push the knob in and tur
anticlockwise to the high position. You should hear and feel a click from the knob. Hold the knob in anticlockwise to the high position. You should hear and feel a click from the knob. Hold the knob in anticlockwise to the high position. You should hear and feel a click from the knob. Hold the knob in
until the burner ignites.
If the burner doesn't light on the first attempt, return the knob to the "OFF" position and try a If the burner doesn't light on the first attempt, return the knob to the "OFF" position and try a If the burner doesn't light on the first attempt, return the knob to the "OFF" position and try a
couple more times. If the burner still does not light, wait a few minutes to allow the gas to disperse
before trying again.
CONTROLLING THE FLAMES CONTROLLING THE FLAMES
The knobs have three basic positions. You can achieve any flame height between low and high by The knobs have three basic positions. You can achieve any flame height between low and high by The knobs have three basic positions. You can achieve any flame height between low and high by
rotating the knob between these positions. rotating the knob between these positio
OFF
Note: 'Blowback' is a situation where the flame burns inside the burner, towards the front, : 'Blowback' is a situation where the flame burns inside the burner, towards the front, : 'Blowback' is a situation where the flame burns inside the burner, towards the front,
recognised by a sharp roaring sound coming from the burner. It is not dangerous unless allowed to recognised by a sharp roaring sound coming from the burner. It is not dangerous unless allowed to recognised by a sharp roaring sound coming from the burner. It is not dangerous unless allowed to
persist .If this occurs, simply turn the burner off, wait a few seconds, and then relight.
turned on at the cylinder, or that gas is available to the barbecue. turned on at the cylinder, or that gas is available to the barbecue.
with "crumpled" aluminium foil.
urner still does not light, wait a few minutes to allow the gas to disperse urner still does not light, wait a few minutes to allow the gas to disperse
High
turn the burner off, wait a few seconds, and then relight. turn the burner off, wait a few seconds, and then relight.
Low