Jumbuck Stardom HS-884302 Assembly & Operation Instructions

2 burner bbq with side burner
Hide thumbs Also See for Stardom HS-884302:

Advertisement

Quick Links

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Stardom HS-884302 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Jumbuck Stardom HS-884302

  • Page 2: For Outdoor Use Only

    BBQ ASSEMBLY & OPERATION INSTRUCTIONS 2 BURNER BBQ WITH SIDE BURNER – MODEL HS-884302 WARNING Important! Please read these instructions carefully before use! FOR OUTDOOR USE ONLY DO NOT OPERATE THIS APPLIANCE BEFORE READING THE INSTRUCTION BOOKLET DO NOT PLACE ARTICLES ON OR AGAINST THIS APPLIANCE DO NOT STORE CHEMICALS OR FLAMMABLE MATERIALS OR SPRAY AEROSOLS NEAR THIS APPLIANCE DO NOT OPERATE THIS APPLIANCE INDOORS...
  • Page 4: Important Safety Instructions

    SAFETY INSTRUCTIONS IMPORTANT: Read the assembly instructions of this booklet before removing the contents of the carton. IMPORTANT SAFETY INSTRUCTIONS 1. This BBQ is an OUTDOOR APPLIANCE ONLY. It should NOT be used indoors. 2. READ ALL OPERATING INSTRUCTION BEFORE LIGHTING. 3.
  • Page 5 FOR YOUR SAFETY FOR YOUR SAFETY If you smell gas: 1. Do not store or use gasoline or other 1. Shut off gas to the appliance at the cylinder. flammable vapors or liquids in the vicinity 2. Open hood. of this or any other appliance. 3.
  • Page 6 IMPORTANT This appliance shall only be used in an above ground open-air situation with natural ventilation, without stagnant areas, where gas leakage and products of combustion are rapidly dispersed by wind and natural convection. WARNING A strong gas smell or the hissing sound of gas indicates a serious problem with your BBQ or the LPG gas cylinder.
  • Page 7: Specification

    SPECIFICATION REGULATOR & HOSE ASSEMBLY: 2.75kPa, POL type regulator and 8mm ID, Class A hose with 3/8SAE Female outlet. AGA approved. Burner Configuration Table - Universal LPG BURNERS NOMINAL GAS TEST POINT INJECTOR CONSUMPTION PRESSURE SIZE 11MJ/h (per burner) ULPG @ 2.75kPa 0.90mm Side 10 .5MJ/h...
  • Page 8 Assembly instruction steps...
  • Page 9 1 Cooking grill 2 Hotplate 3 Warming rack 4 Firebox 5 Flame tamer 6 Left side table 7 Right side table 8 Trivet of side burner 9 Regulator and hose 10 Left side panel of 11 Crossbeam 12 Bottom panel cabinet 13 Back panel 14 Right side panel of...
  • Page 10 21 Door 22 Front panel of right side table Hardware Pack Bolt:M6*12 Washer:M6 Spring washers:M6 Bolt:M5*10 Screwdriver...
  • Page 11 STEP 1: Assemble the castor without lock (19) also castor with lock(20)on the bottom(12) panel by screws (A)(B)(C) each 16pcs STEP 2: Assemble the left side panel of cabinet(10) and the right side panel of cabinet(14) also back panel of cabinet(13) and door magnet panel (18) by screw (A) 12pcs and (D)
  • Page 12 STEP 3: Assemble the crossbeam (11) by screw(A) 4pcs STEP4: Assemble the separation panel of cabinet(15) by screw (A)4pcs...
  • Page 13 STEP 5: Assemble the door handle (17) on the door(21) by screw (A) 2pcs STEP 6: Assemble the door on the cabinet. First position the lower fixed locating PIN and then depress upper spring loaded PIN and move door into position.
  • Page 14 STEP 7: Assemble the firebox(4) on the cabinet by screw (A) 4pcs...
  • Page 15 STEP 8: Assemble the front panel of left side table(16) on the left side table(6) by screw (A) 3pcs, Assemble the front panel of right side table(22) on the right side table (7)by screw (A) 3pcs STEP 9: Assemble the complete left side table (6) and the complete right side table (7) on the firebox by screw (A) 10pcs as below.
  • Page 16 STEP 10: Assemble the side burner injector bracket on the right side shelf and ensure the brass injector is located inside the side burner tube. Fasten the bracket with screw D (2 pcs). Attach side burner ignition wire into the ignition electrode as shown. Side valve Ignition wire...
  • Page 17 STEP 11 Secure side burner hose to the underside hook to hide the hose from view. STEP 12 Insert the flame tamer (5) on the firebox...
  • Page 18 STEP 13 Insert the cooking grill(1) and hotplate(2) on the firebox STEP 14 Insert the warming rack (3) on the firebox...
  • Page 19 STEP 15: Insert the trivet of side burner (8) on the side burner Fully assembled...
  • Page 20 CONNECTION TO LPG CYLINDER LEAK TESTING This should be done the first time you connect up the BBQ, and again each use. Always inspect the hose before each use. Connect the regulator to the LPG cylinder and tighten the connection. Turn the gas on at the cylinder, or make sure gas is available to the BBQ, but do not turn the burners on.
  • Page 21: Lighting Procedure

    LIGHTING PROCEDURE  Lighting the BBQ is easy, but must be done with due care.  Make sure the LPG cylinder is filled.  Make sure that gas is turned on at the cylinder, or that gas is available to the BBQ. ...
  • Page 22 CONTROLLING THE FLAMES The knobs have three basic positions. You can achieve any flame height between low and high by rotating the knob between these positions. High High High High Note: „Light back‟ is a situation where the flame burns inside the burner, towards the front, recognized by a sharp roaring sound coming from the burner.
  • Page 23: After Use

    BBQ TIPS Before cooking, coat the hotplate with oil. This will prevent food from sticking. Light the burners and leave on high for about 3~5minutes to warm the BBQ up. Avoid continually turning the meat over. When cooking internal juices rise to the surface of the meat and then settle.
  • Page 24: Periodic Cleaning

    PERIODIC CLEANING Your BBQ will look better and last longer if you keep it clean. You should check the burners periodically for any sort of blockage. To do this, remove and inspect them. If any of the holes are clogged, gently tap the burner onto a hard surface to remove residue. Use a wire brush to unclog the holes.
  • Page 25 Use an air hose to force air through each burner tube. The forced air should pass debris or obstructions through the burner and out the ports. In addition please also complete the following steps to help prolong burner life. 1. Use a wire brush to clean the entire outer surface of each burner until free of food residue, and dirt 2.
  • Page 26: Care And Maintenance

    IMPORTANT  This product is for outdoor use only. Do not use indoors. Do not use below ground level.  Do not store gas cylinders below ground level. LP gas is heavier than air so if a leak occurs the gas will collect at a low level and could ignite in the presence of a flame or spark.
  • Page 27 Outdoor Areas BBQ LOCATION - Any enclosure in which the appliance is used shall comply with one of the following: An enclosure with walls on all sides, but at least one permanent opening at ground level and no overhead cover. Within a partial enclosure that includes an overhead cover and no more than two walls.
  • Page 28 Both ends open OUTDOOR AREA-EXAMPLE 3 Open sides at least 25% of total wall area 30% or more in total of the remaining wall area is open and unrestricted OUTDOOR AREA-EXAMPLE 4 Open sides at least 25% of total wall area 30% or more in total of the remaining wall area is open and unrestricted...
  • Page 29: Product Warranty

    PRODUCT WARRANTY Thank you for purchasing one of our quality Jumbuck products. Your Jumbuck product is covered against defects for a period of 12 months for parts and labour, repair or replacement. This warranty excludes surface rust and damage caused by abuse or neglect.
  • Page 30  Any repair does not extend the warranty Purchased from………………………………... period. Location………………………………………..  Any parts other than original Jumbuck parts will void this warranty. Model Name and Number…………………….. INSTALLATION CONDITIONS Date of Manufacture……………………………  All installations must conform to the Receipt number………………………………...

Table of Contents