Page 1
BARCO PROJECTION SYSTEMS CINE 6 R9002372 INSTALLATION MANUAL Date : 21112002 Rev : 05 Art. No. : R5975819...
Page 2
Produced by BARCO NV, Nov 2002. All rights reserved. Trademarks are the rights of their respective owners. BARCO n.v./Projection Systems Noordlaan 5 B-8520 Kuurne Belgium Tel : +32/56/368211 Fax : +32/56/351651 E-mail : sales.bps@barco.com Visit Barco at the web : http://www.barco.com Printed in Belgium...
INSTALLATION INSTRUCTIONS Before operating this equipment please read this manual thoroughly, and retain it for future reference. Instal- lation and preliminary adjustments should be performed by qualified BARCO personnel or by authorized BARCO service dealers. OWNER’ S RECORD The part number and serial number are located at the back side of the projector. Record these numbers in the spaces provided below.
This product should never be placed near or over a radiator or heat register. The projector should not be placed in a built-in installation or enclosure unless proper ventilation is provided. 1-2 ___________________________________________________________________________ R5975819.05 BARCO CINE 6 21112002...
Replacement parts - When replacement parts are required, be sure the service technician has used original BARCO replace- ment parts or authorized replacement parts which have the same characteristics as the BARCO original part.
- 1 BARCO CINE 6 - 1 remote control + batteries (2 x 1.5V) - 2 power cables with outlet plug type CEE7 and ANSI 73.11. - owner's manual. - installation manual. - ceiling mount R5975819.05 BARCO CINE 6 21112002 ____________________________________________________________________________ 2-1...
What image size? How big should the image be? The BARCO CINE 6 is designed for projecting an image width from 1.4m (4.6') to 7m (23') with an aspect ratio of 4 to 3. It leaves the BARCO factory, adjusted as a ceiling front projector for a screen width of 2.4m. Changing the image size from the factory preset requires a re-alignment of the projector.
To install the projector, apply always the BARCO kits which are specially designed for this function. BARCO ceiling support Always use the BARCO ceiling support to attach your projector to the ceiling. (BARCO order number : R9827990) The installation instruction for this support is enclosed in the packet of the set.
Page 13
Lift the projector and hook on the 2 screws M8 of the U plate mounted on the ceiling. Fix four M5 screws and nuts to L plate and U plate. Tighten the screws lightly. Align / adjust the picture on the screen and then tighten all (M5 & M8) screws. R5975819.05 BARCO CINE 6 21112002 ____________________________________________________________________________ 3-3...
• Repeat the same for the other side cover. Removing the second top cover : • Loosen the four M4 screws. • Slide the cover a few to the back and lift up. R5975819.05 BARCO CINE 6 21112002 ____________________________________________________________________________ 4-1...
Remarks : As per the factory setting, this photo is in Front / Ceilling position. Color of the wires is as follows : R = Red, B = Blue, Y = Yellow, G = Green 4-2 ____________________________________________________________________________ R5975819.05 BARCO CINE 6 21112002...
Page 17
The three convergence yoke connectors are mounted with the coloured dots on them facing the convergence heatsinks. For table / front mount The three connectors must be reversed so that the heatsinks faces the plane surface. Heatsink R5975819.05 BARCO CINE 6 21112002 ____________________________________________________________________________ 4-3...
Page 18
BARCO LOGO Select with then <ENTER> <EXIT> to return. CINE 6 Proj. address : 001 Soft. Version : 6.00 Config. : Ceiling Front Baudrate PC : 9600 Text : ON Serial No. : 103589552 4-4 ____________________________________________________________________________ R5975819.05 BARCO CINE 6 21112002...
This position of the strap is useful qualified service technicians because they do not need a password during service. Position of the strap (to gain access to the strap, see 'Access to Controls') : R5975819.05 BARCO CINE 6 21112002 ____________________________________________________________________________ 5-1...
Baud rate for communication with a computer Computer communication is only available when the optional RS232 communication port is installed. The communication speed between projector and computer, e.g. PC or MAC, is fixed at 9600 baud rate. 5-2 ___________________________________________________________________________ R5975819.05 BARCO CINE 6 21112002...
Hold Down EHT Input power (mains) voltage adaptation Attention The BARCO CINE 6 - R9002372 leaves the factory with a PFC module to operate on a mains (power) input from 110Vac to 230Vac. Fuses Warning : For continued protection against fire hazard :...
CRT surface. This menu is also displayed, once in red and once in blue. R5975819.05 BARCO CINE 6 21112002 ____________________________________________________________________________ 7-1...
If you are qualified installation or service personnel, press ENTER to start up the installation mode. When entering the installation mode, the projector will automatically switch to the internal pattern on 32 kHz/50 Hz. 7-2 ___________________________________________________________________________ R5975819.05 BARCO CINE 6 21112002...
Page 25
When your password is correct, you get access to the 'ADJUSTMENT MODE'. When the entered password is wrong, the message 'WRONG PASSWORD' will be displayed. COMPOSE PASSWORD ???? 7 8 9 4 5 6 1 2 3 Select with then <ENTER> <EXIT> to return. R5975819.05 BARCO CINE 6 21112002 ____________________________________________________________________________ 7-3...
- ensure the lenses are correctly focused. - open the top cover (see 'Access to Controls') - adjust separately the focus control for red, green and blue for the sharpest image on the screen. 7-4 ___________________________________________________________________________ R5975819.05 BARCO CINE 6 21112002...
Shift the blue raster with the control keys the raster is centered on the CRT faceplate. Press ENTER to continue with the CRT projection angle adjustment ENTER continues to CRT projection angle adjustment. EXIT returns to optical focusing. ADJUST returns to operational mode. R5975819.05 BARCO CINE 6 21112002 ____________________________________________________________________________ 7-5...
The same projection angle is mis- Projection angle correctly aligned aligned for new screen width SW2. for screen width SW1 Re-alignment is necessary. Each screen width change requires re- adjustment of the projection angle. 7-6 ___________________________________________________________________________ R5975819.05 BARCO CINE 6 21112002...
Page 29
Move the blue CRT green crosshair outside, CRT PROJECTION ANGLE away from ADJUSTMENT green CRT. Align cross hairs blue crosshair Move the blue CRT <ENTER> to continue towards the green green crosshair <EXIT> to return. CRT. R5975819.05 BARCO CINE 6 21112002 ____________________________________________________________________________ 7-7...
- vertical linearity adjustment then <ENTER> - vertical size adjustment <EXIT> to return. - horizontal phase adjustment Convergence adjustments - red on green - blue on green Blanking adjustment - top-bottom, left-right Color adjustments 7-8 ___________________________________________________________________________ R5975819.05 BARCO CINE 6 21112002...
PERFORMED ONLY BY QUALIFIED INSTALLATION OR SERVICE PERSONNEL. AS USER OR OPERATOR : PRESS <EXIT> NOW AS QUALIFIED PERSONNEL ABL : ON PRESS <ENTER> Select color with <ENTER> to toggle ABL <EXIT> to return. R5975819.05 BARCO CINE 6 21112002 ____________________________________________________________________________ A-1...