Related Manuals for Elation ELAR DW BRICK
Summary of Contents for Elation ELAR DW BRICK
- Page 1 Elation Professional™ 6122 S. Eastern Ave. Los Angeles, CA. 90040 www.elationlighting.com Rev. 01/06/2011 Version 1.3...
-
Page 2: Table Of Contents
ELAR DW BRICK ™ TABLE OF CONTENS CONTENTS General Information……………………………………………………………………… 2 a. Introduction………………………………………………………………………. 2 b. Unpacking………………………………………………………..…………..… 2 c. Customer Support…………………………………………….………………… 2 d. Warranty Registration……………………………………………………..…… 3 Safety Instructions………………………………………………………..…………. 4 Features……………………………………………………………………………………6 General Guidelines………………………………………………………………………. 7 Fixture Overview…………………………………………………………………………. 8 Mounting and Installation………………………………………………………….……. 10 Understanding DMX……………………………………………………………………... 12 a. -
Page 3: General Information
INTRODUCTION: Congratulations, you have just purchased one of the most innovative and reliable LED fixtures on the market today! The ELAR DW BRICK™ has been designed to perform reliably for years when the guidelines in this booklet are followed. Please read and understand the instructions in this manual carefully and thoroughly before attempting to operate this unit. -
Page 4: Warranty Registration
Please do not discard the shipping carton in the trash. Please recycle whenever possible. WARRANTY REGISTRATION: The ELAR DW BRICK™ carries a two year (730 days) limited warranty. Please fill out the enclosed warranty card to validate your purchase. All returned service items whether under warranty or not, must be freight pre-paid and accompany a return authorization (R.A.) number. -
Page 5: Safety Instructions
4. For safe operation, follow the Installation guide described in chapter two of this manual. Operating the ELAR DW BRICK™ without suited safety aids such as safety cables or clamps can increase the risk of damage and/or personal injury. - Page 6 ELAR DW BRICK ™ replace it immediately with a new one of similar power rating. 13. Always disconnect from main power before performing any type of service or any cleaning procedure. 14. Only handle the power cord by the plug. Never pull out the plug by tugging the wire portion of the cord.
-
Page 7: Features
ELAR DW BRICK ™ 3. FEATURES • Low power consumption • Minimal heat emission • Maintenance free operation • Equipped with 12 three-watt LEDS: (4 cool white, 8 warm white) • 100,000 hours rated LED life • Seamless white and warm color changing •... -
Page 8: General Guidelines
ELAR DW BRICK ™ 4. GENERAL GUIDELINES This fixture is a professional lighting effect designed for use on stage, in nightclubs, in theatres, and other types of architectural installations. Do not attempt operation or installation without a proper knowledge on how to do so. -
Page 9: Fixture Overview
ELAR DW BRICK ™ 5. FIXTURE OVERVIEW 1. LED Assembly –Cool white warm white LED assembly 3 watt LEDS 2. Bracket Locking Knob – This knob is used to secure the bracket in place after angle adjustments have been made. - Page 10 When jumping from fixture to fixture be sure to only use Elation IP rated power connectors to maintain the IP rating. 7. Power Output Jack – Use this jack to jump power to another ELAR DW BRICK™ 8. MENU BUTTON This button is used to access and exit the fixture’s on-board menu...
-
Page 11: Mounting And Installation
Mounting The ELAR DW BRICK™ is fully operational in three different mounting positions, hanging upside-down from a ceiling, side mounted, or set on a flat level surface. Be sure this fixture is kept at least 0.5m away from any flammable materials (decoration etc.). When clamp mounting;... - Page 12 Clamp Mounting The ELAR DW BRICK™ provides a unique mounting bracket assembly that allows the unit to stand on flat surface, hang on truss via a clamp, or be used in cluster allow multiple units to rigged together (see the illustration below).
-
Page 13: Understanding Dmx
ELAR DW BRICK ™ Securing the ELAR DW BRICK™ Always secure your fixture with a safety cable when suspend-ing the unit from truss or other means. The fixture provides a built-in rigging point for a safety cable as illustrated above. Be sure to only use the designated rigging point for a safety cable. -
Page 14: Dmx Terminator
XLR input and output connectors. Always be sure daisy chain your in and out data connections, never split or “Y” your DMX connections unless you are using an approved DMX splitter such as the Elation Opto Branch 4™ or DMX Branch/4™. -
Page 15: 3-Pin To 5-Pin Conversion
ELAR DW BRICK ™ 5-Pin XLR DMX Connectors. Some manufactures use 5-pin XLR connectors for DATA transmission in place of 3-pin. 5-pin XLR fixtures may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin XLR connectors in to a 3-pin line a cable adaptor must be used, these adaptors are readily available at most electric stores. - Page 16 That means changing the settings of one channel will only affect the selected fixture. In the case of the ELAR DW BRICK™, which is a 5 channel fixture (default), you should set the starting DMX address of the first unit to 1, the second unit to 6 (5 + 1), the third unit to 11 (6 + 5), and so on.
-
Page 17: Display Led Indicator
ELAR DW BRICK ™ 8. DISPLAY LED INDICATOR. The ELAR 108PAR RGBW ™ has a LED indicator on the display. This indicator is designed to give a quick visual indication of the fixtures’ DMX status. The illustration below details the functionality of the LED indicators. -
Page 18: Display Menu
ELAR DW BRICK ™ 9. DISPLAY MENU Default settings shaded. VALU A001~AXXX (AXXX) DMX address setting <ADDR> SLAV ON/OFF Set as Slave RDMX ON/OFF Change address via DMX <RUN> AUTO ALON/MAST Run Auto program VALU D-XX D-00(DXXX) Display DMX value... - Page 19 ELAR DW BRICK ™ 9.1 “MODE” - Function Mode: 9.1.1 <ADDR> - DMX address setting – This function is used to set or adjust the fixture’s starting DMX address. Every device controlled by DMX has to have a unique starting address. The addressing feature is what allows DMX to function properly. The DMX address of a fixture is what allows it to communicate with a controller properly.
- Page 20 ELAR DW BRICK ™ the number of steps under “Edit program”. You can edit the individual scenes under “Edit scenes”. With this function, you can run the individual scenes either automatically, i.e. with the adjusted Step-Time. 9.1.3 <DISP> - Menu Display Settings This function allows the internal programs to run in either stand-alone or master/salve DMX chain.
- Page 21 ELAR DW BRICK ™ 9.2 “SET” – Fixture Personality Settings: These functions set specific running modes and operating parameters. <CHAN> DMX Mode settings This function allows the fixture to run in different DMX channel modes. Two modes are available; 5 channel, 10 channel. See “DMX Traits” beginning on...
- Page 22 ELAR DW BRICK ™ 9.4 “TIME” – Operating Hours These functions will detail different time functions associated with the fixture. <LIFE> (0000~9999 Hours) This function tracks the running time of the fixture from the point it was last cleared. Where “XXXX ”represents the total number of running hours. This time is none destructive and will remain in the fixtures memory indefinitely.
- Page 23 ELAR DW BRICK ™ 9.5.5 CEDT - Edit program using a external controller. Editing procedure 1: Using the control board only. 1. Access the main menu. 2. Tap the UP button until “EDIT” is displayed and press ENTER. 3. The display will show “SC-01”, this stands for the scene number. For example, “SC-01”...
- Page 24 ELAR DW BRICK ™ 14. Press MODE/ESC to exit and save your edited scene into the fixtures internal memory. The number of steps can be defined under “EDIT” and the scenes can be called up under “Run.” To run the scenes see page 30.
-
Page 25: Dmx Traits
ELAR DW BRICK ™ 10. DMX CHANNEL TRAITS DMX Operation Notes: The fixture will function in DMX mode whenever the unit is receiving a DMX signal. Please note that this will override all manual settings regardless of dipswitch positions. This unit will keep and retain the last DMX command in the event of DMX signal failure. - Page 26 ELAR DW BRICK ™ 163-255 Color_temperature(5600K) Channel 4 - Strobe: No function (shutter open) Strobe effect slow to fast 1-95 No function (shutter open) 96-127 Pulse-effect in sequences 128-159 No function (shutter open) 160-191 Random strobe effect slow to fast...
- Page 27 ELAR DW BRICK ™ Cool-White ( group2) 0-255 Channel 4 - Warm-White: Warm-White ( group2) 0-255 Channel 5 - Cool-White: Cool-White ( group3) 0-255 Channel 6 - Warm-White: Warm-White ( group3) 0-255 Channel 7 - Cool-White: Cool-White ( group4) 0-255...
-
Page 28: Cleaning And Maintenance
ELAR DW BRICK ™ 11. CLEANING AND MAINTENANCE The consider the following point during normal service and inspection: 1. Be sure all screws and fasteners are securely tightened at all times. Lose screws may fall out during normal operation resulting in damage or injury as larger parts could fall. -
Page 29: Warranty
® defective parts at its expense, and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship. The sole responsibility of Elation Professional under this warranty shall be limited to the repair of the product, or replacement ®... - Page 30 The consumer’s and or Dealer’s sole remedy shall be such repair or replacement as is expressly provided above; and under no circumstances shall Elation Professional® be liable for any loss or damage, direct or consequential, arising out of the use of, or inability to use, this product.
-
Page 31: Photometric Data
ELAR DW BRICK ™ 13. PHOTOMETRIC DATA ©Elation Professional, Los Angeles Ca. www.ElationLighting.com... -
Page 32: Dimensional Drawings
ELAR DW BRICK ™ 14. DIMENSIONAL DRAWINGS ©Elation Professional, Los Angeles Ca. www.ElationLighting.com... -
Page 33: Change Lens To Get Different Beam Angles
ELAR DW BRICK ™ 15. CHANGE LENS TO GET DIFFERENT BEAM ANGLES ©Elation Professional, Los Angeles Ca. www.ElationLighting.com... -
Page 34: Circuit Schematic
ELAR DW BRICK ™ 16. CIRCUIT SCHEMATIC ©Elation Professional, Los Angeles Ca. www.ElationLighting.com... -
Page 35: Technical Specifications
ELAR DW BRICK ™ TECHNICAL SPECIFICATIONS Input voltage: AC 100V-240V~, 50Hz / 60Hz Power consumption: MAX 40W LED Configuration: 12 3Watt Units (4 x Cool white, 8 x Warm white) IP Rating: IP66 Weight: 4 Kgs / 8.8Lbs DMX Channels:... - Page 36 Elation Professional 6122 S. Eastern Ave. Los Angeles, CA. 90040 323-582-3322 / 323-832-9142 fax www.ElationLighting.com / Info@ElationLighitng.com Rev. 01/06/2011 Version 1.3...